Free generator · Runs in your browser

Trophy and medal generator Every winner, printed.

Make a trophy cup, a column award, a medal or a wall plaque: names on a tilted plaque, a star or laurel topper, a ribbon slot sized to your ribbon, a spinning medal centre, and gold, silver and bronze sets for a whole team.

  • Private by designNothing leaves this device
  • Four awardsCups, columns, medals, plaques
  • Honest overhangsSupports flagged when needed
  • Ready to sliceEvery colour its own part

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Award

Make
Cup profile

Tall and flute stretch the cup upwards; the bowl is wider and shallower.

70 mm
70 mm
2.4 mm
30 mm
Knot rings on the stem
Handles
Handles are
14 mm

Printed-on handles keep every slope at 50° or steeper, so they may reach less than this. Glue-on handles print flat and can reach further.

Print the cup

Halves lie flat on their cut face, so any profile prints without supports; glue them together. Upright cups need supports if the bowl is steeper than 45°.

Column
120 mm
110 mm
150 mm
Medal shape
70 mm
4.0 mm
22.0 mm

Measure your ribbon flat with a ruler. Ribbons sold as 7/8 inch are about 22 mm, 1 inch 25.4 mm and 1.5 inch 38 mm, but check yours.

1.0 mm

Added to the ribbon width, so the ribbon slides through without bunching.

Centre
34 mm

The emblem goes on the centre; the text runs around it.

0.35 mm

Raise it if the centre fuses to the medal; lower it if it wobbles. Our tolerance test finds your printer’s number.

0.10 mm

Added to the bearing’s outside diameter. Lower it for a tighter press fit.

0.10 mm

Taken off the cap stem, which presses into the bearing’s bore.

Three medals in gold, silver and bronze, each with its place on top of the text.

110 mm
140 mm

A keyhole slot on the back hangs it on one screw.

Base

90 mm
24 mm

The front plaque sits on this step.

Steps
20 °

Medals and wall plaques have no base. Set the text and emblem in the next steps.

Text

Each name replaces line 2; text after a | replaces line 3. With a medal set, every name gets gold, silver and bronze.

Make several of every item, such as spares or a whole plate of one name.

Check every name

    One per line, up to 60. Add | for a second line, and an order number in square brackets to name each object without printing it: [1042] Olivia | Class 3. Pick your printer below the preview to fill its plates.

    Typeface
    0.8 mm

    Topper and emblem

    On a cup it stands on a lid; on a star column it stands on top; on a plaque it sits above the text.

    50 mm

    Colours

    Preview

    Download

    Building the preview…

    Print it well

      Everything is built on this device. Nothing you type or upload is sent anywhere.

      Advertisement

      Shortcuts

      Start from your kind of project

      The same studio opens ready for each of these: Medal generator.

      The method

      How to make a trophy or medal

      Pick an award, type the event, the name and the year, and the generator builds every part ready to print: the cup and its base, the plaque, a topper on a peg, or a medal with a slot for your ribbon.

      1. Choose the award: a trophy cup, a column award, a medal or a wall plaque.
      2. Size it. For a medal, measure your ribbon’s width.
      3. Add the text and a topper or emblem. For a team, paste a list of names.
      4. Download and print. Each part is its own object, so the cup, base, plaque and text can each take their own filament.

      Options

      What each award is made of

      AwardPartsPrintsNotes
      Trophy cupBase, cup on a stem, plaque, optional lid and topperCup upright or in two halves; plaque flatHandles print with the cup or glue on
      Column awardBase, star column or upright plaque, topperColumn upright; plaque flatThe column fits a peg on the base; the plaque’s tab fits a slot
      MedalMedal, raised text, optional spinning centre or bearing capsFlat, face upRibbon slot = ribbon width + clearance
      Wall plaqueShield, raised text and rimFlat, face upKeyhole slot on the back for one screw

      Printing

      Printing tips

      • Overhangs: slopes of 45° or less from vertical print without supports on most printers. The classic, tall and flute cups stay within that; the bowl does not, so print it in halves or add supports under it.
      • Handles: printed-on handles keep every slope at 50° or steeper. For wide loops, choose glue-on handles, which print flat.
      • Two colours on one nozzle: add a colour change where the raised text starts on a plaque or medal, and at the top of the base on an upright cup.
      • Gold, silver and bronze: in a set, each medal colour is its own part in the 3MF.
      • Spinning centre: the printed-in-place centre needs the right spin gap for your printer. Free it with a twist after printing.

      Questions, answered

      Is it free to use?

      Yes. No account, no watermark, no limits.

      Will it fit my printer?

      Choose your printer below the preview. Parts that don’t fit one plate spread over as many plates as needed, and the download comes with a file per plate.

      Can I sell awards I print?

      The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Do not add logos or names you don’t have the right to use. Medals with spinning centres or bearings have small parts: not for children under 3.

      What ribbon width should I use?

      Measure the ribbon you have. Ribbons are sold in inch widths, such as 7/8 inch (about 22 mm), 1 inch (25.4 mm) and 1.5 inch (38 mm), and the slot adds your clearance on top.

      Sources

      Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

      1. The 45-degree rule in 3D printing Snapmaker
      2. Support material: overhang threshold Prusa Research
      3. Color change Prusa Research
      4. 608 high precision ball bearing data sheet GMN Bearing USA
      5. Ball bearing dimension table (608, 688, 626) igus
      6. R188 series ball bearings NSK
      7. Small parts for toys and children’s products US Consumer Product Safety Commission
      8. SIL Open Font License SIL International