Free generator · Runs in your browser

Phone stand generator Made to measure.

Make a phone or tablet stand from your own measurements: a solid wedge, an open frame, a folding travel stand, a charging dock with a slot for your plug, or a stand for two or three devices. It checks the balance with your device in it.

  • Private by designNothing leaves this device
  • Five stylesFrom pocket stand to dock
  • No supportsEvery style prints as is
  • Ready to sliceSTL or 3MF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Style

Stand

A solid wedge. Sturdy and simple; prints standing, with no supports.

A back rest on an upright leg, open in the middle. Uses less filament; prints standing, with no supports.

Two flat parts that slot together and come apart for travel. Both print flat, with no supports.

A raised seat with a slot for the charging plug, so the cable plugs in while the device stands. Prints standing, with no supports.

Two or three devices side by side, with an optional dock for an earbud case. Prints standing, with no supports.

65 °

How far the screen stands up from the desk: 90° would be upright. 60–70° suits a desk; lower angles lean further back.

Your device

Measure your device with its case on. Calipers are best; a ruler works.

The thickest part, usually across the camera bump.

For a tablet in landscape, its short side.

From the maker’s specification sheet or a kitchen scale. Used only for the tipping check.

1.0 mm

Extra space so the device drops in easily.

Second device

A watch or a small player beside the two.

Stand

70 mm

It can be narrower than the device. Pick your printer below the preview to check it fits.

75 mm

How far up the back of the device the stand reaches, measured along the slope.

7.0 mm

The front lip that stops the device sliding off. Keep it below the screen if you use the bottom of the screen.

6.0 mm
5.0 mm
5.0 mm
0.25 mm

Gap on each side of the leg in the slot. Raise it if the parts are tight, lower it if they wobble.

70 mm

Front to back. Deeper is steadier.

Makes the base deep enough to lean 15° back before it would tip, with your device in it.

Charging and sound

Measure the plug’s hard body, from its tip to the end of the strain relief where the cable can bend.

A pocket in the back rest, open at the top so the pad drops in. Measure your pad.

The pocket is 0.5 mm shallower, so the pad stands proud and touches the device.

From the bottom edge of your device to the middle of its charging coil. If unsure, try charging on the pad and mark where it works.

Opens the lip and slopes the floor under the speaker holes in the bottom edge, so sound comes forward.

22 mm

From the middle of the device’s bottom edge to the middle of the speaker holes.

12 mm

The folding stand has no charging pocket or plug slot; the cable can run under the ledge beside the leg.

A pocket the case stands up in, beside the devices.

Name

Engraved into the front of the lip (the leg on the folding stand). Leave it blank for none.

Typeface
7.0 mm

Long names shrink to fit.

0.8 mm

Colours

A dark grey slab where your device sits, to check the fit. It is never in the download.

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a phone stand that fits

    Measure your device with its case, choose a style and a viewing angle, and the generator works out the groove, the lip, the back rest and the base. It then checks the balance with your device in it, and makes the base deeper if it could tip.

    1. Pick a style: wedge, open frame, folding, charging dock or multi-device.
    2. Enter your measurements with the case on, and the weight.
    3. Add what you need: a plug slot, a charging-pad pocket, sound channels, a name.
    4. Download and print. Every style prints without supports.

    Styles

    The five stands

    StandBest forPrintsOptions
    Solid wedgeDesks, heavy devicesStanding, no supportsPad pocket, sound channels, name
    Open frameTablets, saving filamentStanding, no supportsPad pocket, sound channels, name
    FoldingTravel; it comes apart flatBoth parts flat, no supportsSlot clearance, name on the leg
    Charging dockCharging by cable while standingStanding, no supports; the cable bay roof bridges the plug widthPlug slot, pad pocket, sound channels, name
    Multi-deviceBedside or a shared deskStanding, no supportsTwo or three devices, earbud case dock, pad pocket

    Measuring

    What to measure

    MeasurementHowUsed for
    ThicknessWith the case on, at the thickest pointThe groove width at your angle
    Width and heightHeight is the side that stands upThe device preview and balance
    WeightSpecification sheet or kitchen scaleThe tipping check
    PlugWidth, thickness and length of the hard bodyThe plug slot and seat height of the dock
    Charging padDiameter and thicknessThe pocket, 0.8 mm wider and 0.5 mm shallower
    Charging spotBottom edge of the device to the middle of its coilWhere the pad pocket sits

    Cases, plugs and pads differ a lot between makers, so the generator uses your measurements instead of assumed sizes.

    Balance

    Will it tip over?

    The generator finds the centre of mass of the stand and your device together, and works out how far the stand could lean back before that point passes the back edge of the base. It also gives the push at the top of the screen that would tip it backwards. A deeper base, a steeper angle or a heavier stand all help.

    The stand is counted at about a third of its solid weight, roughly what walls and sparse infill weigh, so a stand printed with more infill is steadier than the readout says. Tapping hard near the top of a tall tablet can still rock it: test it before you rely on it.

    Printing

    Printing tips

    • Standing stands print the way they stand. The back rest leans at your viewing angle, so its underside is never flatter than 40° from vertical, and needs no supports.
    • Charging dock: the bay where the cable bends is open underneath and at the back; its roof is a short bridge across the plug’s width.
    • Folding stand: both parts print flat. The lip has a 45° underside so it needs no supports. Print a tolerance test to choose the slot clearance.
    • Strength: three or four walls and 15–20% infill suit a phone; use more walls for a tablet.
    • Grip: a few small rubber feet stop it sliding on a smooth desk.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. If it is too big, make the stand narrower or the back support shorter; a stand can be narrower than the device.

    Will it hold my device with a thick case?

    Yes, if you measure with the case on. Add a little room in the groove for rugged or wallet cases.

    Will wireless charging work through the stand?

    The pocket holds your own pad level with the back rest, so the device rests on it. Whether it charges depends on the pad lining up with your device’s coil: measure the charging spot height, and test with your case on.

    Can I sell stands I print?

    The designs you make are yours, and the typefaces are open-licensed, which allows making physical products.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Support structures: overhang angles and bridging Polymaker Wiki
    2. Center of mass and stability (Physics, section 12.1) OpenStax
    3. SIL Open Font License SIL International