Free generator · Runs in your browser

Headphone stand and charging station generator Sized to your gear.

Make a weighted headphone stand with a cradle sized to your headband, in four styles, or a desk charging station with slots for your phone, watch puck, earbuds case, tablet, controller and headphones, with the cables run under the base.

  • Private by designNothing leaves this device
  • Stands and stationsFour stands, six holders
  • No supportsEvery part prints as is
  • Ready to sliceSplit to fit your bed

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Make

Make
Style
250 mm

From the desk to where the headband rests. Measure from the top of your headband to the bottom of the ear cups, and add 30 mm or more.

3

They are set out in a row and spaced to fit. Headphone hangers go to the ends so the ear cups hang clear.

Slot 1

Measure with the case on. Width across, and thickness front to back.

15 °

0° stands it upright, like an earbuds case in a pocket.

60 mm

How far up the back of the device the holder reaches.

Cable

Measure your charging puck with calipers: across, and its thickness.

A post and cradle that slot into the base, like the T stand.

Measure across the padding where it rests.

Across the outside of both ear cups. Keeps the other holders clear of them.

Slot 2

Measure with the case on. Width across, and thickness front to back.

15 °

0° stands it upright, like an earbuds case in a pocket.

60 mm

How far up the back of the device the holder reaches.

Cable

Measure your charging puck with calipers: across, and its thickness.

A post and cradle that slot into the base, like the T stand.

Measure across the padding where it rests.

Across the outside of both ear cups. Keeps the other holders clear of them.

Slot 3

Measure with the case on. Width across, and thickness front to back.

0 °

0° stands it upright, like an earbuds case in a pocket.

15 mm

How far up the back of the device the holder reaches.

Cable

Measure your charging puck with calipers: across, and its thickness.

A post and cradle that slot into the base, like the T stand.

Measure across the padding where it rests.

Across the outside of both ear cups. Keeps the other holders clear of them.

Slot 4

Measure with the case on. Width across, and thickness front to back.

15 °

0° stands it upright, like an earbuds case in a pocket.

40 mm

How far up the back of the device the holder reaches.

Cable

Measure your charging puck with calipers: across, and its thickness.

A post and cradle that slot into the base, like the T stand.

Measure across the padding where it rests.

Across the outside of both ear cups. Keeps the other holders clear of them.

Slot 5

Measure with the case on. Width across, and thickness front to back.

15 °

0° stands it upright, like an earbuds case in a pocket.

60 mm

How far up the back of the device the holder reaches.

Cable

Measure your charging puck with calipers: across, and its thickness.

A post and cradle that slot into the base, like the T stand.

Measure across the padding where it rests.

Across the outside of both ear cups. Keeps the other holders clear of them.

Fit

Measure your headband with calipers or a ruler.

Across the padding, where it rests on the stand.

2.0 mm
90 mm

Along the headband’s curve. Longer spreads the weight over more of the padding.

100 mm

Match the inside curve of your headband; larger is flatter.

6.0 mm

Makes the channel deeper for a strip of self-adhesive felt or foam.

3.0 mm
1.0 mm

Added on each side of every pocket.

Measure the hard part of your biggest plug, from its tip to where the cable can bend. The far end of each cable has to pass through its hole.

Sets how high a device that plugs in from below sits.

8 mm

Below each plug, before the cable turns into its channel. More is gentler on the cable.

7.0 mm

Base and post

120 mm
130 mm

The tree widens its base to reach under both arms.

14.0 mm

Made thicker if the weights need it.

Pockets under the base for stacks of weights, glued in.

Mint sizes. Coins wear, so measure one if the fit matters.

4
4
0.30 mm

Added to the weight’s size.

12.0 mm
30 mm
80 mm
Cable holder

Sizes the cable hook or notch on a stand, and the channels under a charging station.

0.20 mm

Gap on each side of every tab, socket and dovetail. Raise it if parts are tight.

6.0 mm

Name and text

Raised on the base in front of the post. Leave it blank for none.

10.0 mm

Long names shrink to fit.

1.0 mm

Add a colour change at the top of the base for two colours.

Typeface

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a headphone stand or charging station

    Measure your headband or your devices, and the generator sizes the cradle or every pocket to them, adds the base, the joints and the cable paths, and lays the parts out on your printer’s plates.

    1. Pick a stand or a station.
    2. Enter your measurements: the headband width, or each device with its case on.
    3. Add the extras: weights, a cable hook, a name, slot labels.
    4. Download and print. Every part prints without supports.

    Options

    Stands and holders

    MakeWhat it isParts
    Arc standA curved post that sweeps forward to the cradleBase, post, cradle
    T standA straight post with the cradle across the topBase, post, cradle
    Minimalist slabA wide flat slab that tapers up to the cradleBase, slab, cradle
    TreeTwo arms at different heights, one headset eachBase, post, two cradles
    Phone, tablet, controllerA pocket that leans back, the plug from below or the cable from behindPart of the base
    Earbuds caseAn upright pocket, the plug from belowPart of the base
    Watch puckA ring that holds a flat charging puck, with a gap for its cablePart of the base
    Headphone hangerA post and cradle that slot into the basePost, cradle

    Measuring

    What to measure

    MeasurementHowUsed for
    Headband widthAcross the padding where it restsThe cradle channel, plus room each side
    Device width and thicknessWith the case on, at the widest pointThe pocket, plus room each side
    Watch puckIts diameter and thicknessA ring 0.5 mm shallower than the puck, so it sits proud
    PlugWidth, thickness and length of the hard partThe passage through the floor, the cable holes and how high the device sits
    CableIts thicknessThe channels under the base
    Coins or nutsMint sizes are built in; measure worn or other coinsThe weight pockets

    Cases, pucks and plugs differ a lot between makers, so the generator uses your measurements instead of assumed sizes.

    Printing

    Printing tips

    • No supports: posts print lying flat, cradles on their flat bottoms, and pockets and channels open underneath have short bridged roofs.
    • Joints: tabs, sockets and dovetails have the joint clearance on every side. Print a tolerance test if you are unsure, and add glue for a firm joint.
    • Weights: glue the stacks into their pockets, then cover the bottom with felt or rubber feet.
    • Two colours on one nozzle: a colour change at the top of the base raises the name or labels in a second colour.
    • Cables: thread the far end of each cable down its hole, press it into its channel from below, and check that it bends gently with nothing pinched.
    • Chargers: leave power adapters in the open, not covered or boxed in.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A post too long for the bed is cut into parts with sliding dovetails, and a station base too wide is cut between holders and joined with bow-tie keys underneath.

    How much weight will it hold?

    It depends on your material, walls, infill and how well the joints are glued, so we don’t give a figure. Headphones are light, but test the stand before you trust it with an expensive headset, and add the weights so it doesn’t tip.

    Does it charge my devices?

    No: it holds your own chargers and cables. Pockets are sized to your measurements, and the plugs and pucks must line up with your devices, so test before you glue anything.

    Can I sell stands I print?

    The designs you make are yours, and the typefaces are open-licensed, which allows making physical products.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Coin specifications United States Mint
    2. Common sides of euro coins European Commission
    3. DIN EN ISO 4032 hexagon nuts fasten.it
    4. Support structures: overhang angles and bridging Polymaker Wiki
    5. Lithium-ion batteries: charging safely West Yorkshire Fire and Rescue Service
    6. SIL Open Font License SIL International