Free generator · Runs in your browser

Box generator Print it or cut it.

Make a box to your exact size: a sliding, hinged, snap-fit, magnetic or screw-top lid, compartments and a label for your 3D printer, or finger-jointed panels for a laser cutter as SVG or DXF.

  • Private by designNothing leaves this device
  • Seven lidsIncluding a print-in-place hinge
  • No supportsEvery overhang 45° or less
  • STL, 3MF, SVG, DXFFor printers and laser cutters

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Box

Make it by
Sizes are

Inside sizes are the space you get. Outside sizes include the walls and, when closed, the lid.

80 mm

Left to right. A screw-top round box uses this as its diameter.

60 mm

Front to back.

40 mm
4.0 mm
2.0 mm

Multiples of your line width print best: 1.2, 1.6, 2 or 2.4 mm with a 0.4 mm nozzle.

1.6 mm

Lid and joints

Lid

A plate with a lip that pushes into the box.

The lid runs in 45° dovetail grooves in the side and back walls and slides out the front. A finger notch helps you open it.

Printed in one piece, lid and box together, laid open flat. The knuckles are printed apart by the clearance and turn on cone pins: no supports, no assembly.

Bumps on the lid’s lip click into a groove inside the walls.

Posts in the corners and the lid hold disc magnets: glue them in, checking that each pair attracts.

A round box with a screw-on cap. The width is its diameter; depth is not used.

0.30 mm

The gap between parts that move or fit together. Tight printers fit at 0.2 mm; print a tolerance test if unsure.

2.0 mm

Grows on its own when the lid needs room for magnets, a label or a stacking recess.

4.0 mm

How far the lip under the lid reaches into the box.

Measure your magnets: the pockets are 0.3 mm wider and 0.2 mm deeper.

3.0 mm

Measure your sheet with calipers: sheets sold as 3 mm are often a little thinner or thicker.

0.10 mm

The width your laser burns away. Cut a 20 mm square, measure it: kerf = 20 − what you measure. Every cut moves out by half of it.

10 mm

Each edge gets an odd number of equal fingers close to this width, at least twice the material thickness.

Top

Panels are packed onto as many sheets as they need, one file per sheet.

300 mm
200 mm

Inside

1
1

1 row and 1 column is an open box. More make a grid of compartments.

Dividers

Divider plates print flat and slide into slots in the walls; their half-depth notches interlock. Needs walls of 1.6 mm or more; about 2.4 mm with a snap-fit lid and 3.2 mm with a sliding lid.

1.6 mm
100 %

Of the inside height, kept below the lid’s lip.

Rounds the inside where the floor meets the walls, so small parts slide out with a finger.

A foot under the box drops into the box below, or into a matching recess on its lid. Not for sliding lids or round boxes.

Feet
10.0 mm

Measure your stick-on pads. Printed feet push into the pockets; print them in flexible filament for grip.

Label and colours

Label
Typeface
50 mm

Cut a card to this size: the slot fits card up to about 0.8 mm thick.

20 mm
Preview
Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a box

    Set the size you need, choose a lid, add dividers and a label, and download a file ready to print or cut. Everything is built on this device.

    1. Pick how you’ll make it: a 3D printer, or a laser cutter and flat sheet.
    2. Set the size by the inside (the space you need) or the outside (the space it fills).
    3. Choose a lid or, for laser cutting, a closed box, an open tray or a lift-off lid.
    4. Add compartments: rows and columns of dividers, fixed or removable.
    5. Download. STL or 3MF for printing, with the lid and dividers laid out beside the box; SVG or DXF for the laser, one file per sheet.

    Lids

    Which lid to choose

    LidHow it closesHow it printsGood for
    FrictionA lip pushes into the wallsBox upright, lid upside downEveryday storage
    SlidingRuns in 45° dovetail groovesBox upright, lid flatPencils, long thin things
    HingedKnuckles on cone pins, printed in placeOne piece, laid open flatTrinkets and gifts
    Snap-fitBumps click into a grooveBox upright, lid upside downBoxes that get carried
    MagneticDisc magnets in corner posts and lidBox upright, lid upside down; glue the magnetsGift boxes
    Screw-top roundA coarse thread on the neckJar upright, cap upside downJars and small parts
    NoneOpen trayUprightDrawer organisers and stacking trays

    Laser cutting

    Laser-cut finger-joint boxes

    Each edge is split into an odd number of equal fingers. Where two panels meet, one panel’s fingers fill the other’s gaps; the front and back own the corners. Dividers are an egg crate: plates with half-depth slots that slot together and stand on the bottom panel.

    • Kerf: the beam burns away a thin line. The generator moves every cut out by half the kerf, so each finger comes out full size and the joint is snug. Measure your kerf on a test square first.
    • Test a joint: cut one corner before the whole box. Too tight: lower the kerf a little. Too loose: raise it.
    • The files: red hairline cut paths in millimetres, every panel a named path, one file per sheet.
    • Assembly: the joints hold by friction; a little wood glue makes the box permanent. Leave the lift-off lid’s two plates to glue together.

    Options

    Sizes and options

    SettingRangeWhat it does
    Inside or outside size20–300 mm across, 8–200 mm highInside sizes are kept exactly; outside sizes take the walls, floor and lid off
    Wall1.2–5 mmSliding lids need 2 mm, snap-fit 1.6 mm; removable dividers need 1.6 mm, or more with those two lids
    Clearance0.1–0.6 mmThe gap at every lid, hinge, thread and divider fit
    DividersUp to 8 × 8Fixed bars, or removable plates in wall slots
    Magnets6–10 mm discsPockets 0.3 mm wider and 0.2 mm deeper than the magnet
    Laser material1–12 mmFinger width at least twice the thickness

    Printing

    Printing tips

    • No supports: every overhang is 45° or less, and the lid prints upside down so its top is on the bed.
    • Hinged lid: print as laid out, with the lid open flat behind the box. After printing, work the hinge gently a few times to free it.
    • Clearance: if a lid is tight, print again with 0.05 mm more; if it’s loose, with less.
    • Magnets: glue them in with the box and lid side by side, checking that each pair pulls together before the glue sets.
    • Engraved labels: a lid printed upside down has its letters on the bed side, so they come out crisp.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. The box, lid and dividers are laid out side by side, and spread over several plates if they need to. If the box itself is too big, make it smaller or cut it on a laser instead.

    Can I sell boxes I make?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Magnets and printed feet are small parts, so check toy-safety rules before selling boxes for children.

    Which file do I need for a laser cutter?

    SVG works in most laser software; DXF is for CAD and some cutting programs. Both are in millimetres with the kerf already applied, so don’t add a kerf offset in your software as well.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Modeling with 3D printing in mind Prusa Research
    2. Test kerf offset LightBurn Software
    3. Accounting for kerf: how much material is really removed by your cutter? Make:
    4. Birch plywood product datasheet (density for the weight estimate) Metsä Wood
    5. SIL Open Font License SIL International