Free generator · Runs in your browser

Pet bowl stand generator Sized to your bowls.

Make a raised feeder that fits the bowls you already have: measured holes, the height you choose, an optional tilt, your pet’s name on the front, plus a slow-feeder insert and a mat edge.

  • Private by designNothing leaves this device
  • Your bowlsHoles sized to your measurements
  • No supportsThe top prints on the bed
  • Fits your printerSplit with dovetails

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Make

What to make
Bowls
120 mm

From the floor to the top of the stand. Measure your pet and ask your vet what height suits them; we don’t suggest one.

Tilted stands are popular for cats. The bowl centre stays at the height above.

15 °

A maze that sits on the floor of the bowl you already have, for dry food. Measure the bowl in the next step.

A tray with a raised edge that catches spills around the stand. Lay a washable mat inside.

Measure the bowl

160 mm

The widest part at the top, over the lip.

135 mm

Where the bowl meets the stand: the hole is this plus the clearance. It must be smaller than the rim so the lip rests on the stand.

50 mm

From the top of the rim to the bottom of the bowl.

1.0 mm

Bowls sized to the measurements above. For water and wet food, use a stainless steel or ceramic bowl.

150 mm

Across the flat bottom inside the bowl, where the sides start to curve up.

20 mm

Keep it below the rim of the bowl.

Pattern
520 mm

The stand footprint shows in the readout of the stand; add 60–100 mm.

320 mm
10 mm

Style

Sides
Pattern

The legs push into sockets under the top and print lying down, so a tall stand still fits your printer.

Typeface
1.2 mm

Shallow round recesses for stick-on rubber or felt pads.

20 mm
1.5 mm

No style options for this part.

Colours

Stand, mat and legs
Name
Bowls and insert
Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a raised feeder that fits your bowls

    Bought raised feeders come in fixed sizes. Here you measure the bowls you already have and set the height you want, and the generator builds a stand with holes that fit, split to your printer’s bed.

    1. Measure your bowl: across the rim, across the body just under the lip, and its depth.
    2. Set the height from the floor to the top of the stand. Ask your vet what height suits your pet.
    3. Pick a style: solid sides, a cut-out pattern or legs, and add your pet’s name.
    4. Download and print. The top prints on the bed, so no supports are needed.

    Measuring

    What to measure

    MeasurementWhereUsed for
    Rim diameterAcross the top, over the lipThe lip must be wider than the hole so the bowl hangs from it
    Just under the lipAcross the bowl body, right under the lipThe hole: this plus the clearance each side
    DepthRim to the bottom of the bowlThe stand is never lower than the bowl, so it stays off the floor
    Inside floor (insert)Across the flat bottom insideThe slow-feeder insert, 3 mm smaller

    Options

    Styles and extras

    OptionWhat it isPrints
    Solid sidesFour walls, pad recesses under the cornersUpside down, one piece per bed
    Cut-out patternPaw prints, bones or fish cut through the sidesUpside down; the cut-outs bridge short gaps
    LegsA top with a 40 mm apron and push-in square legsTop upside down; legs lying on a side, in sections if long
    TiltThe top leans 5–20° towards the frontUpside down, the same way
    Printed bowlA bowl sized to your measurements, with a 45° lipUpright, no supports. Dry food only
    Slow-feeder insertMaze rings or spokes on a disc that sits in your bowlFlat. Dry food only, supervised
    Feeding mat edgeA tray with a raised edge, split to your bedFlat, pieces joined by dovetails

    Food and safety

    Food, cleaning and height

    • Printed parts are for dry food. Printed plastic has layer lines and small gaps that trap food and are hard to clean. Use a stainless steel or ceramic bowl in the stand for water and wet food.
    • Clean regularly: wash the bowls every day and wipe the stand top and insert often.
    • Ask your vet about height. We found no published veterinary formula for feeder height, so we don’t suggest one. A veterinary evidence review found that the studies on raised bowls and bloat (gastric dilatation-volvulus) in large and giant breed dogs disagree; one linked raised bowls to a higher risk. If your dog is a large or deep-chested breed, ask your vet first.
    • Supervise pets with the slow-feeder insert, and take it out if it gets chewed.

    Printing

    Printing tips

    • Material: PETG copes with water and knocks better than PLA.
    • Strength: 4 or more walls and 25% infill. Glue dovetails and legs for a stiff stand.
    • Build height: a solid stand prints as tall as it stands. For tall stands, choose Legs.
    • Name in a second colour: the name is its own part in the 3MF for a multi-material printer, or paint it.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A wide stand splits between the bowls into pieces that fit the bed, and long legs split into sections. A solid stand needs as much build height as it is tall.

    What height should I use?

    Ask your vet. We found no published veterinary guideline for raised feeder height, so the height is yours to set.

    Can I sell stands I print?

    The designs you make are yours, and the typefaces are open-licensed, which allows making physical products. We make no claims about load, food safety or pet health, so don’t promise any.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Are dogs that are fed from a raised bowl at an increased risk of gastric dilation volvulus compared with floor-fed dogs? Veterinary Evidence (RCVS Knowledge)
    2. Food safe FDM printing Prusa Research
    3. PETG Prusa Research
    4. SIL Open Font License SIL International