Free generator · Runs in your browser

Wall clock generator Your dial, your movement.

Design a wall clock round the quartz movement you bought: raised numerals in a second colour, a name, an open skeleton or photo centre, matching hands, a keyhole hanger, a desk stand, and a split for small printers.

  • Private by designNothing leaves this device
  • Six dial shapesPlus your own outline
  • No supportsDial, hands and stand print flat
  • Ready to sliceNumerals their own colour

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Dial

Shape
250 mm

Across a round dial, the flats of a hexagon or octagon, or the longer side of your outline. Bigger than your bed? It splits into pieces (step 6).

5.0 mm

Thicker than your movement’s shaft allows? Turn on the back pocket in step 4.

Edge
4.0 mm
2.4 mm

Above the dial face. It stops the hands from catching on a wall frame.

Numerals

Most Roman clock dials use IIII instead of IV, which balances the VIII opposite.

14 %

Of the dial’s radius. Kids’ clocks read best at 20% or more.

Typeface

60 short marks, longer at each hour.

1.2 mm

Numerals, markers, ticks and the name stand this far above the face, as their own colour.

One or two lines: a name, family name or a date.

8 %

Of the dial’s radius. Shrinks to fit the width.

Centre

Centre

Cut right through, so the wall shows behind. The hub round the movement, the numeral ring and a plaque under any text stay solid, and the dial stays one connected piece.

20 mm
4

Each number gives a different arrangement.

24
3.5 mm

3 mm or more keeps a big dial stiff.

A lithophane shows the photo only with light behind it, so hang the clock in a window or put a light strip behind it. In room light it reads as a soft relief. The movement hides the middle.

0.8 mm
3.0 mm

Movement

Measure your movement. Sizes differ between makers; the values below are only common listings for a mini quartz movement with a 5/16 in threaded shaft.

The threaded part the nut screws onto. A 5/16 in shaft is 7.9 mm.

Added to the thread diameter. 1.6 mm makes the 3/8 in (9.5 mm) hole clock-part sellers suggest for a 5/16 in shaft.

Listed with the movement, often as “for dials up to 1/4 in” (6.4 mm). The dial is this thick at the movement.

Only cut when the dial is thicker than the shaft allows. The ceiling bridges like any flat overhang.

How far the movement stands off the back; the clock hangs this far from the wall.

Hang it from

Measure the screw in your wall. The keyhole needs a dial at least 5.6 mm thick.

Hands

Or use the metal hands that come with most movements.

Style

Measure the hand posts on your movement. Hand holes are not standardised between makers.

The round tube nearest the dial.

Set it equal to the one above for a round hole.

0.00 mm

Added to every hand hole. Raise it if hands will not press on; lower it if they slip.

1.6 mm

Stand, fit and colours

A base with a slot that holds the dial upright on a shelf or desk.

Pick your printer below the preview for the automatic split. Pieces join with printed peg plates and glue on the back.

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a wall clock

    Buy a battery quartz clock movement first, measure it, then design the dial round it. The generator sizes the shaft hole and the back pocket from your measurements, raises the numerals for a second colour, prints matching hands and splits a big dial to fit your printer.

    1. Pick the shape and size and the edge: plain, a raised rim or a wide frame.
    2. Choose numerals, ticks and any name or date.
    3. Pick a centre: solid, an open skeleton, or a photo lithophane.
    4. Enter your movement’s sizes: the shaft thread, the thickest dial it takes and the body.
    5. Add hands and a stand, pick your printer to check the split, and download.
    6. Assemble: push the shaft through from the back, add the washer and nut on the front, then press on the hour, minute and second hands, all pointing at 12.

    Movement

    Measuring the movement

    MeasureTypical listingWhy it matters
    Shaft thread5/16 in (7.9 mm) on many mini movementsSets the hole; 1.6 mm clearance gives the suggested 3/8 in hole
    Thickest dial1/8 to 3/4 in, by modelThe dial is cut to this at the movement, by the back pocket
    BodyAbout 2 1/8 in square, 5/8 in deepThe back pocket is 1 mm bigger each way
    Hand holesNot standardisedMeasure the hour tube, minute post and second pin
    Hand lengthUp to about 6 in (152 mm) on standard movementsLonger hands need a high-torque movement

    These are listings from clock-part sellers, not a standard. Calipers on your own movement beat any table.

    Options

    Dials, centres and pieces

    OptionChoicesNotes
    ShapeRound, square, rounded square, hexagon, octagon, your outlineSize is across the round, the flats, or your outline’s longer side
    NumeralsArabic, Roman, 12-3-6-9, dots, bars, noneRaised for a colour change, all the same height
    Skeleton centreVoronoi cells or sunburst raysCut through; the dial stays one piece
    Photo centreA lithophane round the shaftNeeds light behind it; prints in one piece only
    Pieces1, 2 or 4Seams run between the numerals; joiner plates glue across them

    Printing

    Printing tips

    • Dial face up, no supports. The back pocket and keyhole are flat overhangs that most printers bridge cleanly.
    • Two colours on one nozzle: add a colour change at the dial thickness shown under the preview; the numerals, ticks and rim print in the second colour.
    • Hands: print flat with 0.12–0.16 mm layers so the holes come out round, and test-fit one before printing the rest.
    • Photo centre: print it in white at 100% infill, the way lithophanes are printed.
    • Split dials: glue the pieces on a flat table, then glue the joiner plates over the seams on the back.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A dial bigger than the bed splits into two halves or four quarters with joiner plates; a photo dial is made smaller to fit instead.

    Which movement do I need?

    Any battery quartz movement with a threaded shaft and a nut. Check the thickest dial it takes against the dial thickness here, and measure its hand posts if you print the hands.

    Can I sell clocks I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Only upload outlines and photos you have the rights to use.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-11. Community posts are one maker's experience, not a specification.

    1. Mini quartz movements for dials up to 1/2 in thick Clockparts.com
    2. Mini quartz clock movement S&T Supply
    3. Clock parts FAQ Clockparts.com
    4. Color change Prusa Research
    5. SIL Open Font License SIL International