Free generator · Runs in your browser

Worry stone generator Smooth, calm, yours.

Make a smooth worry stone with a thumb dip: a pebble, a heart or your own shape, with sensory textures and a word or name engraved. It prints as two flat halves with no supports, and a classroom set packs onto your printer’s plates.

  • Private by designWords stay on this device
  • Five shapesOr your own outline
  • No supportsTwo flat halves, glued
  • Ready to sliceSTL and 3MF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Shape

Shape
6

Rounds off corners and small bumps.

40 mm

The long way across, seen from above. Many worry stones are about 3 cm; a little bigger is easier to hold. For your own outline, this is its longer side.

30 mm
12.0 mm
0.45

Low gives a slim, lens-like stone; high a fuller one with rounder sides.

Thumb dip

Thumb dip
3.0 mm

Kept shallow enough to leave at least 1.6 mm of stone each side of the middle.

22 mm

About the size of the pad of your thumb: press it on a ruler to measure.

16 mm
0.0 mm
0.0 mm
0 °

Texture

Carved gently into the surface, for fingers to explore.

Where
0.5 mm
3.0 mm

2.5 mm and up stays crisp at a 0.4 mm nozzle.

Engraving

Engrave

One stone per line: a list of words makes a set, such as a calm-down set for a classroom.

Make several of every item, such as spares or a whole plate of one name.

Check every stone

    One per line, up to 30. Add | for a second line, and an order number in square brackets to name each object without printing it: [1042] Olivia | Class 3. Pick your printer below the preview to fill its plates.

    Typeface
    Symbol
    Engrave on

    On a face with a dip, it goes in the dip.

    7.0 mm

    Long words shrink to fit the stone.

    0.6 mm

    Print and colours

    Print as

    Split flat at the widest line. Each half prints flat with no supports; glue them together.

    Short pieces of 1.75 mm filament line the halves up while the glue sets.

    One piece with a flat cut on the bottom. Honest warning: the curve below the widest line overhangs, so the lower edge prints a little rough without supports.

    2.0 mm

    More gives a bigger, steadier base and less overhang.

    Each stone takes the next colour: jade, grey, sand, rose and marble white.

    Lists the heights to change filament at, for stripes like a banded stone.

    Preview

    Download

    Building the preview…

    Print it well

      Everything is built on this device. Nothing you type or upload is sent anywhere.

      Advertisement

      The method

      How to make a 3D printed worry stone

      A worry stone is a smooth stone with a dip for your thumb. Pick a shape and size, set the dip, add a texture or a word if you like, and the generator builds a fully rounded stone, split into two halves that print flat with no supports.

      1. Pick a shape: a pebble, a heart, a round or rounded-square stone, or your own outline.
      2. Set the thumb dip: its depth, size and place, on one side or both.
      3. Add a texture or a word: ripples, dots or a spiral for restless fingers; a name, a calming word or a small symbol.
      4. Print the halves flat face down, glue them together with filament pins to line them up, and sand lightly.

      Options

      Shapes, dips and textures

      SettingDefaultWhat it does
      Size40 × 30 × 12 mmMost worry stones are about 3 cm across; a bit bigger is easier to hold and harder to lose
      Plumpness0.45Low makes a slim lens; high gives fuller, rounder sides
      Thumb dip22 × 16 mm, 3 mm deepA smooth oval hollow, deepest in the middle, blending into the stone with no edge
      TexturesOffRipples, dots, waves, ridges, a spiral or knurl, carved 0.2–1.2 mm deep
      Engraving0.6 mm deepA word or symbol, in the dip on a face that has one
      Two halvesWith pin holes2 mm holes, 3 mm deep, for 1.75 mm filament pins
      Whole2 mm flat baseOne piece; the lower curve overhangs, so expect a rougher lower edge

      Printing

      Printing and finishing tips

      • Halves: print flat face down; each is a low dome that needs no supports. Glue the faces with super glue or two-part epoxy and clamp gently.
      • Pins: cut two pieces of 1.75 mm filament about 5.5 mm long and push them into one half before gluing, so the halves line up.
      • Smooth: a fine layer height (0.12–0.16 mm) shows fewer layer lines on the dome. Sand lightly with 400 then 800 grit; wet sanding keeps the dust down.
      • Weight: 100% infill makes the stone feel solid. PLA and PETG both work; PETG is tougher if it gets dropped.
      • Layered look: turn on the layered colour option for the heights to change filament at.
      • Whole stones: the curve under the widest line overhangs. A bigger flat base helps; supports give the cleanest result.

      Good to know

      What people use them for

      People hold a worry stone and rub the dip with their thumb to keep their hands busy, during a test, a meeting or before sleep. Classrooms and calm-down corners use sets of stones with words like “breathe” and “brave”. A worry stone is not a medical device, and we make no health claims.

      Questions, answered

      Is it free to use?

      Yes. No account, no watermark, no limits.

      Will it fit my printer?

      Choose your printer below the preview. One stone and its halves fit any printer; a set fills as many plates as it needs, one file per plate.

      Why print it in two halves?

      A rounded stone printed whole has a curve under its widest line that leans outward, which prints rough without supports. Split flat at the widest line, each half is a dome that prints cleanly with no supports, and the glue line sits right on the edge.

      Can I make a set for a class?

      Yes. Choose A word or name and put one word per line (up to 30), or import a CSV. Each stone gets its own word, and the set is packed onto your printer’s plates. In the 3MF every stone is its own object, named after its word.

      Is it safe for small children?

      Small stones are a choking hazard and glued halves can come apart: not for children under 3. We make no toy-safety or health claims.

      Can I sell stones I print?

      The designs you make are yours, and the shapes, textures and symbols here are drawn for this generator. The typefaces are open-licensed, which allows making physical products. Use only outlines you have the rights to. No claims beyond that.

      Sources

      Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

      1. Worry stone Wikipedia
      2. Small parts ban and choking hazard labeling US Consumer Product Safety Commission
      3. Color change Prusa Research
      4. SIL Open Font License SIL International