Free generator · Runs in your browser

Deck box and card stand generator Sized to your deck.

Make a deck box from your card count and measured card thickness: flip-top with a print-in-place hinge, magnet lid, sleeve or drawer. Or a stand for a card, top loader or graded slab, a tiered riser, a wall frame or a bulk box.

  • Private by designNothing leaves this device
  • Boxes, stands, framesEight kinds of holder
  • No supportsEverything prints as laid out
  • Ready to sliceLids and letters their own objects

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

What to make

Make
Box
Stand
Holds

Top loaders differ a little between makers: measure yours with calipers.

77.0 mm
101.0 mm
1.60 mm

Measure across the middle, not at the open end.

Magnetic holders come in several thicknesses: measure yours with calipers.

85.0 mm
111.0 mm
6.0 mm

Graded slabs differ between grading companies: measure yours with calipers.

86.0 mm
140.0 mm
7.5 mm

Cards

Published card sizes. Pick Custom and measure for anything else.

63.0 mm
88.0 mm
3.0 mm

Measure a sleeve’s width and take away the card’s width. It adds the same to the height.

0.31 mm

Measure 20 cards pressed together with calipers and divide by 20.

0.30 mm

Measure 10 sleeved cards and divide by 10, then take away the card thickness. Double sleeves: measure them double sleeved.

100

The inside depth is this many cards times the thickness above, plus the clearance.

Fit and features

Decks
6 mm

The cards sit below the rim, so the lid swings clear of them. Extra depth leaves room for a few tokens.

30 mm

How much of the cards the lid covers.

Pockets are 0.3 mm wider and 0.2 mm deeper than the magnet. Measure yours if unsure.

0.30 mm

The gap between the hinge parts. If the hinge fuses, print again with 0.05 mm more.

22.0 mm

Measure your largest die across its widest point.

A name, or a symbol such as ★ ♦ ♣ or ☀. Short words print biggest.

Typeface
Letters

The letters become their own object for a multi-colour printer.

Lids print upside down, so their letters are always engraved. Raised letters go on the front of the sleeve and drawer boxes.

15 °
75 mm

Wider than the item by 6 mm or more and the groove closes at both ends.

3
22 mm

How much higher each row stands than the one in front.

2
2
300
2
4

Loose divider cards with a tab, printed flat.

0.40 mm

Added to the measured thickness. 0.4 mm holds most items snugly.

1.0 mm

Added to the deck’s width, height and depth (and the frame pockets’ size).

2.0 mm

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a deck box or card stand

    Measure your cards, pick what to make, and the generator sizes every pocket and groove from your numbers. A deck box is as deep as the card count times one card’s thickness (sleeve included), plus the clearance.

    1. Pick the card size and say whether the cards are sleeved.
    2. Measure the thickness: press 20 cards together with calipers and divide by 20; do the same with 10 sleeved cards for the sleeve.
    3. Choose a box, stand, frame or bulk box, and its features.
    4. Download and print. Each piece is its own object, so lids and letters can take their own filament.

    Card sizes

    Card sizes

    CardCard sizeSleeved (about)
    Standard63 × 88 mm66 × 91 mm (measure yours)
    Japanese small59 × 86 mm62 × 89 mm (measure yours)
    Poker63.5 × 88.9 mm66.5 × 91.9 mm (measure yours)
    Bridge57.15 × 88.9 mm60.15 × 91.9 mm (measure yours)
    Tarot70 × 120 mm73 × 123 mm (measure yours)
    Mini42 × 63.5 mm45 × 66.5 mm (measure yours)

    Card sizes are from a card printer’s published table. Sleeves, top loaders, magnetic holders and graded slabs vary between makers, so the generator asks you to measure them.

    Options

    What it makes

    MakeOptionsPrints
    Flip-top boxPrint-in-place hinge, lid depth, dice pocket, token trayIn one piece, the lid laid open flat
    Magnet-lid boxDisc magnets in the rim, one or two decks, dice pocketBox upright, lid upside down
    Slide-in sleeveThumb cut-out on both faces, one or two decksUpright
    Drawer boxCards lie flat, finger notch, letters on the frontShell on its back, drawer upright
    Card standCard, top loader, magnetic holder or graded slab, lean 0–30°On its base
    Tiered riser2 to 5 steps, each with a grooveOn its base
    Wall frame1 × 1 to 3 × 3, bevelled windows, keyhole hangersFrame face down, back plate flat
    Bulk boxUp to 1,500 cards in 1 to 4 rows, divider cardsUpright, dividers flat

    Printing

    Printing tips

    • Hinge: print the flip-top box as laid out with no supports, then open and close it gently a few times. Print a small test first if your printer is new to you.
    • Grooves: card grooves are under a millimetre wide. If a card won’t go in, raise the groove clearance by 0.1 mm.
    • Magnets: check the poles pull together before the glue sets.
    • Two colours: engraved letters filled with a second colour print face down on the first layers, for a sharp finish on a multi-colour printer.
    • Wall frame: press the back plate on; a drop of glue on each peg makes it permanent. Use screws with heads up to 8 mm across for the keyholes.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Pieces spread over as many plates as needed; a bulk box longer than the bed needs fewer cards per row or more rows.

    Can I sell boxes and stands I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Don’t put other companies’ logos or game names on things you sell. Magnets are small parts: not for children under 3.

    Why do I have to measure the thickness?

    Card stock and sleeves differ between makers, and a deck of 100 sleeved cards can vary by several millimetres. Measuring a stack and dividing gives a box that fits your deck.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Playing Card Dimensions PrintNinja
    2. Color change Prusa Research
    3. SIL Open Font License SIL International