The method
How to make a printable mandala
A mandala is a design that repeats round its centre. Draw in one wedge and the pad repeats every stroke round the circle as you go, or press Make me one for a layered mandala built from rings of motifs. Both can be combined.
- Draw or generate. Pick the symmetry (3 to 24), mirror on or off, and draw with lines, arcs, rings, dots and stamps.
- Edit the rings. Change any ring’s motif, count, style, position and size, or re-roll just that ring.
- Choose what to make: a cut-through panel or trivet, a relief coaster, a two-colour inlay, a stencil or a suncatcher.
- Check the preview. Lime bridges show where loose pieces were tied back. Download the STL or 3MF.
What you can make
Five ways to print a mandala
| Make | What prints | Good for |
|---|---|---|
| Cut-through | The design lines and an outer ring; the gaps are open | Wall pieces, window panels, trivets |
| Relief | The design standing on a solid backing, pad recesses underneath | Coasters, trivets, plaques |
| Two-colour inlay | A backing and the design as a separate part, flush or raised | Multi-colour printers, or one filament change |
| Stencil | A thin sheet with the design cut out, islands bridged | Paint, chalk, icing sugar, sand art |
| Suncatcher | A frame of design lines and thin translucent glass by ring | Windows; hangs by its loop |
Nothing falls out
Islands, bridges and line widths
In a cut-through panel, a stencil or a suncatcher frame, any piece not joined to the rest would drop out when printed. The generator finds those islands, ties each one back with the shortest bridge it can find (outward, inward or sideways), and copies the bridge round with the design’s symmetry so the mandala stays even.
Lines thinner than two nozzle widths cannot print reliably, so every line is drawn at least that wide and any sliver narrower than that is left out.
| Setting | Suggested | Why |
|---|---|---|
| Line width | 2–3 mm for cut-through | Stiff enough to handle and clean |
| Bridge width | 1.4–2 mm | About three to four nozzle lines |
| Thickness | 3–4 mm wall piece, 5–6 mm trivet | Flat and rigid |
| Stencil sheet | 0.6–0.8 mm | Bends to curved surfaces |
Printing
Printing tips
- No supports: everything prints flat. Keyholes are slotted at the bed with the head chamber behind, and only bridge short gaps.
- Trivets: printed plastic softens well below the heat of a pan from the stove. PLA starts to soften around 50–55 °C, PETG around 70 °C and ASA around 95–100 °C, so use a trivet for warm dishes and teapots, not hot pans.
- Two colours on one nozzle: the advice under the preview gives the height to change filament.
- Suncatchers: print the glass in translucent filament; each glass colour is its own part in the 3MF.
- Big wall pieces: if the piece is larger than your bed, lower the size or print it on a larger printer.
Questions, answered
Is it free to use?
Yes. No account, no watermark, no limits.
Will it fit my printer?
Choose your printer below the preview to check. If it is too big, lower the size; copies can be spread over several plates in your slicer.
Can I sell what I print?
The mandalas you draw or generate are yours, and the motifs are original to this site. No typefaces are used. Sell them as you like; check any rules that apply to products for food or for children yourself.
Is my drawing uploaded?
No. Everything is built on this device. Share links hold the drawing and settings in the link itself.
Why are there small bars across some gaps?
Those are bridges. Without them, pieces surrounded by gaps would fall out of a cut-through panel or a stencil.
Sources
Print advice is a starting point drawn from these references, checked on 2026-11-13. Community posts are one maker's experience, not a specification.
- Mandala Wikipedia
- Advanced filament guide Prusa Research
- What 3D filament is heat-resistant? Snapmaker
- What is the minimum wall thickness for 3D printing? QIDI Technology
- Color change Prusa Research