Free generator · Runs in your browser

Yarn bowl generator Made to fit your yarn.

Make a yarn bowl sized to your ball, with a smooth J or spiral slot, cat ears, leaves or a name, plus needle and hook holders, thread spool racks, bobbin holders, stitch markers and a row counter.

  • Free and privateNothing leaves this device
  • Five craft toolsBowls to row counters
  • No supportsPrints as laid out
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Make

What to make
95 mm

Measure across the widest point. As a start: small ball (about 75 mm), medium ball or cake (about 95 mm), large cake (about 115 mm).

4.0 mm

So the ball turns freely as you pull the yarn.

85 % of the ball

How far up the ball the wall comes. Higher keeps the ball in and makes room for a longer slot.

2.6 mm
Tools
Holder
0.6 mm

Each hole is the size plus this, so the tool drops in.

30 mm
120 mm

About a third of your longest needle is enough to stand them up.

24
6
6.5 mm

Measure the hole of your smallest spool.

45 mm
32 mm

Across the widest flange or the thread. Sets the peg spacing.

4 mm
15 °

Pegs lean up (on a wall) or back (on a table) so spools stay on.

Mount
8.0 mm
4.0 mm
Holder
21.0 mm

Starts at the class 15 size its maker publishes (21 × 12 mm). Measure yours.

12.0 mm
12
3
Make

The markers and the counter slide over this needle.

10
1.2 mm

A little narrower than your yarn squashed lightly, so the marker clips on.

Slot and pattern

Yarn slot
7.0 mm

Wider than your yarn; 6–8 mm suits most yarn up to bulky.

12 mm
18 mm

How far the end of the slot runs sideways.

12 °

Flatter holds the strand better but bridges more; 45° needs no bridge.

Pattern
1.2 mm
12
7
Typeface

It rests on the rim and closes the top of the slot.

Slots and patterns are for the yarn bowl. Pick colours below.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a yarn bowl

    Measure your yarn ball or cake, choose a slot and a pattern, and the generator builds a bowl with the ball plus room inside, a slot cut right through the wall from the rim, and a heavy 45° foot that prints without supports.

    1. Measure the ball across its widest point.
    2. Pick the slot: a J slot holds the strand best; a spiral slot needs no bridge.
    3. Add a pattern, cat ears, a name and a lid if you like.
    4. Download and print upright; sand the slot edges smooth.

    Options

    What you can make

    ToolWhat you getMeasure
    Yarn bowlA bowl with a J or spiral slot, patterns, a name and a lidYour ball or cake
    Needle and hook holderA stand that doubles as a size gauge, or a cup with a labelled sorting topNothing: sizes come from the chart
    Thread spool rackA wall or tabletop rack with angled pegsSpool hole, height and diameter
    Bobbin holderA ring, tray or stack of tubes with a windowBobbin diameter and height
    Stitch markers and row counterOpen rings with numbered tabs, and a ring counter that turns on its hubYour yarn, for the gap

    Sizes

    Needle and hook sizes

    Labels and holes follow the Craft Yarn Council chart. A few common sizes:

    MillimetresUS knitting needleUS crochet hook
    2.25 mm1B-1
    3.5 mm4E-4
    4 mm6G-6
    5 mm8H-8
    6 mm10J-10
    8 mm11L-11
    10 mm15N/P-15

    Yarn weights and the needles the same council recommends:

    WeightNameNeedles
    0Lace1.5–2.25 mm
    1Super fine2.25–3.25 mm
    2Fine3.25–3.75 mm
    3Light3.75–4.5 mm
    4Medium4.5–5.5 mm
    5Bulky5.5–8 mm
    6Super bulky8–12.75 mm

    Printing

    Printing tips

    • Smooth slot: the slot has rounded ends and bevelled edges; sand them lightly, or print with a fine layer height, so yarn never catches.
    • No supports: the bowl, holders, racks and markers all print as laid out. A flat J hook bridges a short distance: keep cooling at full.
    • Material: PLA or PETG. PETG flexes a little more, which suits stitch markers.
    • Row counter: it prints in place; twist the ring firmly once to free it.
    • Small parts: markers and counters are not for children under 3.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A large yarn bowl needs a bed and height a little bigger than the ball; lower the ball size or the wall height if it is too big. Racks and markers spread over more plates when needed.

    Can I sell what I print?

    The designs you make are yours, and yarn bowls and needle holders are traditional shapes anyone may make. The typefaces are open-licensed, which allows making physical products. There are no claims beyond that.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Hooks & Needles Craft Yarn Council
    2. Standard Yarn Weight System Craft Yarn Council
    3. How do I choose the right bobbin? Singer
    4. Layers and perimeters Prusa Research
    5. SIL Open Font License SIL International