Free generator · Runs in your browser

Infinity cube generator Fold it forever.

Make a print-in-place infinity cube in your size and colours: eight cubes and eight hinges, printed in one go with no assembly and no supports. Fold it on screen first to see how it moves.

  • Private by designNothing leaves this device
  • Prints in placeHinges come off the bed working
  • Your size12 to 30 mm cubes
  • Ready to sliceSTL, 3MF and per-colour files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Cube

Make

Two cubes and one hinge, made exactly like the real thing. Print it first: if it folds freely, the full cube will too.

18 mm

The finished cube is twice this, plus the gap.

Hinges
0.8 mm

Softens the corners and hides elephant’s foot on the bottom edges.

Fit

0.300 mm

The gap inside each hinge. Use your tolerance-test result; 0.3 mm suits most tuned printers.

0.30 mm

Stacked cubes print on this gap like on a support interface. Make it at least one layer height.

Colours

Pattern

Try it

0.00

0 is the cube as printed, 4 is the second cube with the inside faces out. Downloads are always the cube, ready to print.

The hinge test prints as laid out. Fold it by hand once it’s printed.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How a print-in-place infinity cube works

    An infinity cube is eight small cubes joined in a ring by eight hinges. It folds open from the middle and closes into a second cube with its inside faces showing, then back again, as long as you keep going. Here it prints in one piece, already assembled.

    Each hinge is a barrel on the edge between two cubes, split into three knuckles. The ends of the knuckles are 45° cones that nest into each other with a small clearance. That holds the hinge together and prints without supports. The layout keeps every hinge on the outside in all 24 positions the cube can fold into, so no barrel is ever trapped between two cubes.

    1. Print the hinge test at the size you want, and adjust the clearance until it folds freely.
    2. Pick a size and colours for the cube.
    3. Print it as laid out, with the plain face down and no supports.
    4. Free each hinge by flexing it gently, then start folding.

    Using it

    How to fold it

    1. Hold it so one line of two hinges runs across the top, left to right, and another across the bottom.
    2. Open it out. Flip the back top pair of cubes up and over, so it stands on top of the front pair, and the back bottom pair down and under, below the front pair. You’re holding a flat block, four cubes tall and two wide.
    3. Fold the block in half down the middle, the way its hinges let it, so it’s one cube wide and two deep.
    4. Fold it in half across the middle. It closes into a cube again, with its inside faces out.
    5. Keep going. The same moves bring back the first cube. Drag the Fold the preview slider to watch each step.

    Sizes

    Choosing a size

    Small cubeFinished cubeGood for
    12–14 mm25–29 mmKeychain-sized, slim hinges, needs a well-tuned printer
    16–20 mm33–41 mmClassic desk fidget, standard hinges
    22–30 mm45–61 mmBig, chunky and easy to print, sturdy hinges

    Smaller cubes have smaller hinges. Below about 15 mm, print slowly with 0.12–0.16 mm layers.

    Printing

    Printing tips

    • Layers: 0.15–0.2 mm. The gap between stacked cubes should be at least one layer, so the upper cubes start on it the way a part starts on a support interface.
    • No supports, no brim inside the gaps: a brim around the outside is fine.
    • First layer: elephant’s foot can join the bottom cubes. The edge chamfer helps; lower the first-layer flow if it still sticks.
    • Freeing it: flex each hinge a little at a time before folding the whole cube.
    • Material: PLA or PETG. Silk and matte PLA in two colours look great.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    A hinge is stuck. What now?

    Flex it gently back and forth, holding the two cubes close to the hinge. If it won’t free up, print the hinge test with 0.05 mm more clearance, or run the tolerance test to find your printer’s number.

    The upper cubes are stuck to the lower ones.

    The gap between stacked cubes prints like a support interface. Raise the gap to 0.4 mm, or use thinner layers so the gap spans more than one layer.

    Is it safe for children?

    It’s a hand toy, not for under-threes: printed parts can break into small pieces.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-09. Community posts are one maker's experience, not a specification.