Free generator · Runs in your browser

Furniture foot and riser generator Level, lift, protect.

Make leg caps and glides, tube plugs, risers, bed lifters, levelling feet and caster cups sized to your measured leg, with pad recesses and screw holes, in sets laid out on your printer’s plates.

  • Private by designNothing leaves this device
  • Six kindsGlides, risers, levelling feet
  • No supportsPrinted upright
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Product

Make
4

A set for every leg. Pick your printer below the preview to spread them over its plates.

Leg

For a tube plug, measure the inside of the tube with calipers, not the outside.

Shape

Measure the leg (or the tube’s inside) where it meets the floor.

Measure the leg at the cup depth set below, above the floor.

0 for sharp corners. Rounded corners are common on metal tube and planed wood.

0.30 mm

Added to every side of the leg. Use 0.1–0.2 for a snug push fit, more for a loose cap you glue on. For plugs, how much smaller the ribbed core is than the tube.

3.0 mm
15 mm

For twin wheels, measure across both.

8 mm

Deeper holds the wheel better but makes the cup harder to roll into.

Fit

The cup is sized from the wheel: a trough 1 mm wider than the wheel each side, curved to its radius, inside a rim at least 6 mm wide.

5.0 mm

Countersunk from underneath, with head sizes from DIN 7997. Choose Measured for other screws.

16 mm
0.30 mm

How much bigger than the tube’s inside the ribs are.

Sets the cap so it ends flush with the outside of the tube.

4.0 mm
50 mm

How much higher the leg stands. A pad adds its own thickness.

10 mm

How much wider than the cup the base is on each side. Wider is steadier.

110 mm

A wide base spreads the load on soft floors and carpet.

Underside
Type

An insert caps the leg and has a threaded hole; a printed foot screws into it.

For a leg with a bolt or threaded rod fixed in it: the foot holds a hex nut and screws onto the bolt.

10 mm
40 mm
0.20 mm

0.15–0.2 mm for printed parts that screw together.

Pads

Pad recess underneath
1.0 mm

Holds a stick-on felt or rubber pad in place. Pads thicker than the recess stand proud of it.

A pad for each piece, its own object, sized to the recess.

2.5 mm

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    Shortcuts

    Start from your kind of project

    The same studio opens ready for each of these: Bed riser generator.

    The method

    How to make feet that fit your furniture

    Measure the leg, pick what you need, and the generator builds a set sized to that leg, laid out on your printer’s plates.

    1. Pick the product: a cap or glide, a tube plug, a riser, a bed lifter, a levelling foot or a caster cup.
    2. Measure the leg with calipers where it meets the floor: diameter, or width and depth and the corner radius. For tapered legs, measure again at the cup depth. For tube plugs, measure the inside of the tube.
    3. Set the fit: the clearance each side, the lift height, the thread and its adjust range.
    4. Print one and test it on the leg before printing the whole set.

    Products

    What each one is for

    ProductUse it forPrints
    Leg cap or glideMissing glides, scratched floors, a sleeve over the leg endOpen side up
    Tube leg plugOpen metal tube legs on chairs and tablesCap down, ribs up
    RiserRaising a table, desk or cabinet 10–150 mmBase down
    Bed or sofa lifterRoom for storage under a bed or sofa, on a wide baseBase down
    Levelling footWobbly tables and uneven floorsThread axis vertical
    Caster cupKeeping wheeled furniture from rolling and marking the floorFlat side down

    Reference

    Threads, nuts and screws

    ThreadDiameter (mm)Pitch (mm)Nut across flats (mm)Nut height (mm)
    M66.01.0105.2
    M88.01.25136.8
    M1010.01.5168.4
    1/4-20 UNC6.351.27011.15.7
    5/16-18 UNC7.941.41112.76.9
    3/8-16 UNC9.521.58714.38.6

    Metric threads follow ISO 68-1 with ISO 4032 nuts. Inch threads are Unified coarse (UNC), which uses the same 60° profile, with the largest finished hex nut sizes from ASME B18.2.2.

    ScrewHead (DIN 7997)Clearance holeCountersink
    3 mm5.6 mm3.5 mm6.2 mm
    4 mm7.5 mm4.5 mm8.1 mm
    5 mm9.2 mm5.5 mm9.8 mm
    6 mm11 mm6.5 mm11.6 mm
    3.5 mm6.5 mm4.0 mm7.1 mm
    4.5 mm8.3 mm5.0 mm8.9 mm

    Load

    How much will it hold?

    We don’t give load ratings. A printed foot’s strength depends on the material, the walls and infill, the printer and how the load sits on it.

    • Test before trusting: load each piece with more than it will carry, and check it again after a few days. Plastic creeps under a steady load, PLA most of all.
    • Walls and infill: feet are crushed, not bent. Use 4 or more walls and 40% or more infill, or solid for small parts. Strength comes mostly from walls; infill adds resistance to crushing.
    • Not for seats or steps: don’t use printed feet on chairs, stools or steps that people sit or stand on, or under anything that could tip onto someone.

    Printing

    Printing tips

    • Upright, no supports: risers, lifters and cups print base down, open at the top. Hollow undersides use 45° walls.
    • Material: PETG for the feet; TPU for pads that grip and protect the floor, or stick on felt.
    • Threads: print the thread axis vertical, with layers about a sixth of the pitch.
    • Fit first: print one, try it on the leg, and change the clearance before printing the set.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A set fills as many plates as it needs, and the download comes as a file per plate.

    How strong is it?

    We don’t rate loads. Thicker walls, more infill and PETG make stronger feet. Test them with more than the weight they will carry, and don’t use them on chairs or steps people sit or stand on.

    My leg isn’t round or square. What now?

    Use the nearest shape and a larger clearance, then glue the cap on, or use a riser cup a little bigger than the leg.

    Can I sell feet I print?

    The designs you make are yours. We make no claims about load or safety, so test anything you sell and don’t promise a weight it will hold.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Infill Prusa Research
    2. Layers and perimeters Prusa Research
    3. PETG Prusa Research
    4. Flexible materials Prusa Research
    5. ISO metric screw thread Wikipedia
    6. DIN EN ISO 4032 hexagon nuts fasten.it
    7. Unified Thread Standard Wikipedia
    8. Hex nut dimensions table (ASME B18.2.2) amesweb.info
    9. DIN 7997: cross-recessed countersunk head wood screws, dimensions fasten.it