Free generator · Runs in your browser

Tool outline tracer Photo in, organizer out.

Photograph your tools on a sheet of paper next to a bank card. Get a drawer insert, tray, grid bin or wall board with a pocket shaped to each tool.

  • Private by designThe photo never leaves this device
  • One photoA card beside the tools sets the scale
  • Five things to makeInsert, tray, grid bin, wall board, fit check
  • Ready to slice or cutSTL, 3MF, SVG and DXF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Photo and scale

  1. Lay the tools on a plain sheet of paper: light paper for dark tools. Leave a finger-width between them.
  2. Put a bank or ID card flat beside them. It sets the scale.
  3. Take the photo from straight above, with even light and the whole sheet in view.
  4. Choose the photo below. It stays on this device.

The examples are drawn by this page, so you can try every setting before taking a photo.

Getting the example ready…

Drag a corner dot to move it, or press Next corner and use the arrow keys. Click an outline to choose that tool.

Scale from

Any ID-1 size card works: bank, ID and most loyalty cards are 85.60 × 53.98 mm. Keep it flat, on the paper, at the same height as the tools.

Put the sheet on a darker table so all four edges show. Tools must lie fully on the sheet.

Drag the two dots onto the ends of something you measured, such as a ruler. No tilt correction with this choice.

For flatbed scans: dots per inch ÷ 25.4. The photo is resized to at most 1,500 pixels on its long side first.

Tracing settings
Background

Picks the level that best separates tools from paper (Otsu’s method).

35 %

Lower picks up faint parts; higher ignores more.

25 %

Grey areas this much darker than the paper count as shadow, not tool.

1 px

Evens out paper grain and print on the tools.

8 mm
0.15 mm

How far an outline may move to become smoother.

Closes ring ends and handle holes so each pocket is one clean shape.

Tools and pockets

Choose a tool to rename it, set its depth, turn, mirror, move, merge or delete it.

    12.0 mm

    About half the tool’s thickness holds it and leaves it easy to lift. Measure your thickest tool.

    0.50 mm

    Each pocket is the traced outline grown by this much on every side.

    0.6 mm

    Fills crevices narrower than twice this, which would not print cleanly.

    Round cut-outs on both sides of each tool so you can pinch it.

    20 mm

    Insert

    Make

    A 1 mm plate with the pockets cut through. Print it first, drop the tools in, then change the clearance if needed.

    The bin grows to a whole number of 42 mm grid squares and has the stepped feet that sit in 42 mm grid baseplates.

    Layout

    Measure the drawer. The insert is made 1 mm smaller.

    2.0 mm
    4.0 mm
    1.6 mm

    A wall board is at least 5.6 mm here, to make room for the keyhole slots.

    6.0 mm
    2.0 mm

    The usual height step for bins on this grid.

    Measure your screws.

    Pockets alone do not hold tools on a wall. A magnet glued under each steel tool does.

    Measure your magnets: sizes vary a little.

    0.20 mm

    Choose your printer under the preview, or set the largest tile below.

    Round puzzle keys lock the tiles together.

    Two-colour shadow

    A second colour under each tool shows at a glance when one is missing. The layer suits multi-colour printers. The sheet (drawer inserts and trays) suits any printer: pockets are cut through and a thin sheet is glued underneath.

    0.6 mm

    Cut 0.6 mm into the top, under each pocket. Rename tools in step 2.

    5.0 mm

    Colours and outline files

    Grey stand-ins for your tools. They are never part of the download.

    SVG and DXF files hold the pocket outlines, the traced tools and the plate at true size in millimetres, for a laser cutter or for cutting foam by hand.

    Download

    Building the preview…

    Print it well

      Everything is built on this device. Nothing you type or upload is sent anywhere.

      Advertisement

      The method

      How to make a tool organizer from a photo

      The page finds everything that is not paper, measures it against the card, and cuts a pocket for each shape. Nothing is uploaded: the photo is read and traced on your device.

      1. Lay out: tools on plain paper with a finger-width between them, and a bank or ID card flat beside them.
      2. Photograph from straight above. Step back and zoom in a little: it flattens the picture.
      3. Check the scale: the four dots should sit on the card’s corners. Drag them if not.
      4. Tidy the tools: delete stray shapes, name the tools and set a depth for thick ones.
      5. Print the fit check, then the insert.

      Scale

      How the scale is found

      ReferenceTrue sizeCorrects tilt?Use it when
      Bank or ID card85.60 × 53.98 mm (ID-1 size)YesYou have any standard card. It is found automatically.
      A4 sheet297 × 210 mmYesThe tools lie on the sheet and the table is darker than the paper.
      US Letter sheet279.4 × 215.9 mm (11 × 8.5 in)YesAs A4, in North America.
      Known lengthWhat you measuredNoThere is a ruler or a measured tool in the photo.
      Pixels per mmWhat you typeNoThe picture is a flatbed scan with a known resolution.

      The four corners of the card or sheet give a perspective map (a homography), so a photo taken at a slight angle is straightened to true scale. A photo from almost straight above is treated as flat, because small errors in the corners of a small card would otherwise be magnified across the picture. A bigger reference is more exact: a full sheet beats a card.

      Options

      What you can make

      MakeWhat it isGood for
      Drawer insertA plate sized to your drawer, split into keyed tiles if it is bigger than the printerTool chests and workbench drawers
      TrayOne plate with a raised rim, sized to the toolsA set that moves around: a bench kit, a travel roll
      Grid binA block with stepped feet on a 42 mm grid, in whole grid squaresDrawers already fitted with 42 mm grid baseplates
      Wall boardA board with keyhole slots on the back, and optional magnet pocketsA shadow board above the bench
      Fit checkA 1 mm plate with the pockets cut throughA quick test before a long print

      Clearance is the gap added around each traced outline: 0.3 mm is snug, 0.5 mm is a good start, 1 mm is loose. Every pocket can have its own depth, so a thick handle and a thin blade can sit level.

      Be realistic

      How accurate is it?

      • Expect about a millimetre, not a hundredth. Phone lenses bend straight lines a little, most of all near the edges of the picture, and this page does not correct that.
      • Height matters. The card sets the scale at paper level. A thick tool is closer to the camera, so it looks slightly bigger, and its sides can show. Photograph from further away to reduce both.
      • Keep the card in the same plane as the tools: flat on the paper, not propped up.
      • Shadows and shine can add to or eat into an outline. Use soft, even light and raise the shadow tolerance if grey edges are picked up.
      • Print the fit check first. It takes minutes and shows exactly where a pocket is tight.

      Printing

      Printing tips

      • Flat on the bed, pockets up, no supports. Keyhole slots on a wall board bridge a short gap on the back.
      • Tiles: each tile is its own object. The round keys push together; a drop of glue makes it permanent.
      • Two colours: with a multi-colour printer, give the shadow layer its own filament. With one nozzle, choose the sheet: print it in the second colour and glue it under the insert.
      • Thin walls: walls under about 1.2 mm between pockets print weak. Raise the minimum wall or move a tool.
      • Material: PLA is fine indoors. Use PETG where it gets warm or oily.

      Questions, answered

      Is it free to use?

      Yes. No account, no watermark, no limits.

      Is my photo uploaded?

      No. The photo is opened, measured and traced in your browser. It is not sent anywhere and is not saved when you leave the page.

      Will it fit my printer?

      Choose your printer below the preview. Inserts bigger than its bed are split into tiles with keyed edges, one tile per plate. Grid bins are one piece and are not split.

      The card was not found. What now?

      Drag the four dots onto the corners of the card yourself. A card that is close in colour to the paper is hard to see: use a darker card, or switch to a paper sheet or a known length.

      Does it work with grid storage systems?

      The grid bin has a 42 mm pitch and the stepped foot profile from the open specification for that grid, so it sits in baseplates made to the same specification. It has no stacking lip.

      Can I sell what I print?

      The designs you make from your own photos are yours. The typeface used for engraved names is open-licensed, which allows making physical products. We make no fit or safety claims, so test what you sell.

      Sources

      Print advice is a starting point drawn from these references, checked on 2026-11-13. Community posts are one maker's experience, not a specification.

      1. ISO/IEC 7810:2019 Identification cards: physical characteristics (ID-1 is 85.60 × 53.98 mm) International Organization for Standardization
      2. ISO 216:2007 Writing paper and certain classes of printed matter: trimmed sizes, A and B series International Organization for Standardization
      3. Paper size: North American paper sizes (Letter, 8.5 × 11 in) Wikipedia
      4. A threshold selection method from gray-level histograms (Otsu, 1979) IEEE Transactions on Systems, Man, and Cybernetics
      5. Basic concepts of the homography explained with code OpenCV documentation
      6. Gridfinity unofficial specification (42 mm grid, foot profile) Gridfinity community
      7. gridfinity-rebuilt-openscad: standard dimensions kennetek (MIT licence)