Free generator · Runs in your browser

Bookmark generator Keep your place in style.

Make a name bookmark with a tassel hole, a cat or fox corner bookmark, a clip or a reading tracker: patterns, your own silhouette, two colours, and a bookmark for every name on a list.

  • Private by designNames stay on this device
  • Four typesFlat, corner, clip and tracker
  • No supportsEverything prints flat
  • Ready to sliceExact colour-swap layer

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Bookmark

Type
Shape
50 mm
152 mm

50 × 152 mm is the common 2 × 6 inch bookmark; 2 × 7 inches (178 mm) is the next size up.

5.0 mm

5 mm takes a folded loop of embroidery thread or a thin ribbon.

Tracker
12

Twelve boxes for a book a month, or one mark per chapter on the scale.

0.30 mm

Added to the bookmark’s thickness inside the marker. Lower holds tighter; raise it if the marker will not slide.

Face
55 mm

Each of the two edges that run along the page edges.

Measure the pages it will hold with calipers. For one page, measure 100 pages and divide by 100.

0.30 mm

Added to the pages, then rounded up to whole layers.

1.4 mm
Topper
42 mm
16 mm
1.0 mm

At least two nozzle widths, so the tongue prints free.

1.6 mm

1.2 mm flexes with the page; 1.6 mm is stiffer; 2 mm and up hardly bends.

Text

One bookmark per line. Add | for a smaller second line.

Make several of every item, such as spares or a whole plate of one name.

Check every bookmark

    One per line, up to 40. Add | for a second line, and an order number in square brackets to name each object without printing it: [1042] Olivia | Class 3. Pick your printer below the preview to fill its plates.

    Corner bookmarks show the text with the Heart and Name only faces.

    Typeface
    20.0 mm

    Height of a capital letter. Long names shrink to fit.

    Direction
    Lettering
    0.6 mm

    Keep it low so it doesn’t mark the pages.

    0.6 mm

    Three layers at 0.2 mm (0.6 mm) give solid colour.

    0.20 mm

    Grows every stroke so thin scripts print solid.

    Design

    8.0 mm
    1.6 mm

    Three or more nozzle widths keep the bars strong.

    3.0 mm

    A picture or SVG under the text: a cat, a leaf, a logo.

    Silhouette

    Patterns and silhouettes are for flat bookmarks and trackers. Corner faces and clip toppers are drawn for you.

    Colours

    Sets the colour-swap layer and rounds the corner pocket to whole layers.

    Preview

    Download

    Building the preview…

    Print it well

      Everything is built on this device. Nothing you type or upload is sent anywhere.

      Advertisement

      The method

      How to make a 3D printed bookmark

      Pick a type, type a name and choose a pattern or a face. The generator traces the letters, flows the pattern around them, adds a tassel hole and tells you where to swap filament for a second colour.

      1. Pick a type: a flat bookmark, a corner that slips over the page, a clip, or a reading tracker.
      2. Type the name. One name per line makes a bookmark for each, packed onto your printer’s plates.
      3. Add a design: a cut-out pattern, your own silhouette, or a face for a corner bookmark.
      4. Download and print flat. No supports, and the page gives the colour-swap layer.

      Types

      Which bookmark?

      TypeHow it holds the pagePrints as
      Flat bookmarkSits between the pages, with an optional tasselOne flat piece
      CornerA pocket slips over the corner of the pageTwo flat pieces: a back with a rail and pins, and a face that presses on
      ClipThe page slides between a sprung tongue and the frame, like a paper clipOne flat piece
      Reading trackerA flat bookmark with tick-boxes, or a scale with a marker that slides along itOne flat piece, plus the marker ring

      Sizes

      Sizes and settings

      SettingDefaultWhy
      Flat bookmark50 × 152 mmThe common 2 × 6 inch bookmark; 2 × 7 inches (178 mm) is the next size up
      Thickness1.6 mmStiff enough to keep its shape; 1.2 mm bends with the page
      Raised letters0.6 mmLow enough not to press into the pages
      Tassel hole5 mmTakes a folded loop of embroidery thread
      Corner pocketYour pages + 0.3 mmMeasured, then rounded up to whole layers
      Clip slot1 mmTwo or more nozzle widths, so the tongue prints free

      Printing

      Printing tips

      • Two colours on one nozzle: for raised letters, swap filament where the letters start. For the two-colour inlay, start in the letter colour and swap where the face starts; the letters show through.
      • First layer: a thin, wide part lives or dies by its first layer. Clean the plate and slow the first layer down.
      • Flex: PLA is stiff and can snap if bent hard; PETG bends and springs back, which suits clips and thin bookmarks.
      • Corner bookmarks: press the face onto the back’s pins. A drop of glue on each pin makes it permanent; keep glue off the pocket.
      • Patterns: bars of three or more nozzle widths stay strong; finer patterns look delicate but tear more easily.

      Questions, answered

      Is it free to use?

      Yes. No account, no watermark, no limits.

      Will it fit my printer?

      Choose your printer below the preview. A 2 × 6 inch bookmark fits almost any printer; a batch fills as many plates as it needs, one file per plate.

      How do I size the corner pocket?

      Measure the pages it will hold with calipers. Paper is thin, so for one page measure 100 pages and divide by 100. The pocket is that thickness plus the clearance, rounded up to whole layers at the layer height you print. Too tight? Add 0.1 mm of clearance.

      Can I make a bookmark for everyone in a class?

      Yes. Put one name per line (up to 40) or import a CSV. Pick your printer and the bookmarks fill its plates in order. In the 3MF each bookmark is its own object, named after its line.

      Can I sell bookmarks I print?

      The designs you make are yours, and the faces and patterns here are drawn for this generator. The typefaces are open-licensed, which allows making physical products. Use only pictures you have the rights to.

      Sources

      Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

      1. What are the most popular bookmark sizes? PrintKeg
      2. Color change Prusa Research
      3. View slicing information (pauses and filament changes) Bambu Lab
      4. SIL Open Font License SIL International