Free generator · Runs in your browser

Stained glass suncatcher generator Let the light in.

Make a stained glass suncatcher from a built-in design or your own picture: thin translucent glass pieces set in raised lead came, in a circle, arch, rectangle, hexagon or heart. Or make a papel picado banner of cut-paper flags.

  • Private by designPictures stay on this device
  • Five designs and your picturePlus papel picado banners
  • One nozzle or manyHonest options for each
  • Ready to sliceEach glass colour its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Make

Make a
Start from
Design
6

The picture is grouped into this many colours. Each one is a filament.

12 mm²

Pieces of glass smaller than this join the piece next to them, so the came doesn’t swallow them.

35 mm

Large areas of one colour are cut into pieces about this size, with came between them, as real glass would be. 0 leaves them whole.

1.00 mm

Rounds the jagged edges a photo leaves between colours.

Pattern
Letters

One per flag spells the word along the banner (up to 16 letters; spaces are skipped).

Typeface
6

With one letter per flag, the banner has one flag per letter.

Shape and size

Shape
140 mm

Pick your printer below the preview to check it fits.

180 mm
3.0 mm

The came round the outside edge.

Makes the frame taller than the came inside it, like a picture frame.

1.2 mm
Hang it with
4.0 mm
2.5 mm

Suction cups vary. Measure the narrow neck under the knob with calipers or a ruler.

90 mm
120 mm
1.0 mm

Thin flags look like cut paper. 1 mm is five 0.2 mm layers.

The channel along the top is 0.6 mm wider, so the string slides through.

1.6 mm

Thin strips that hold the middles of letters and shapes in place.

Print

Printer

A multi-material printer: each glass colour is its own filament, side by side.

One nozzle: a clear or translucent sheet, then a colour change for the came.

One nozzle: the came alone, to fill with tinted resin or paint.

A colour change on one nozzle swaps the colour for a whole layer, so it can’t put colours side by side. That’s why one-nozzle printers get a single sheet or open cells.

0.8 mm

Thin glass lets more light through. 0.6–1 mm suits most translucent filaments.

1.6 mm

The lines between pieces. 1.6 mm is four lines from a 0.4 mm nozzle.

2.4 mm

Taller than the glass, so the lines stand out and hold the panel stiff.

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a stained glass suncatcher

    Pick a built-in design or add a picture. The design is split into pieces of glass, and every border between them becomes raised “lead came” like a real leaded window, joined to a frame round the outside. The glass is thin, so light comes through; the came is opaque and taller, so the lines stand out.

    1. Choose a design or a picture, and how many glass colours.
    2. Pick a shape and size, and a loop or a suction-cup hole to hang it.
    3. Choose how you’ll print it: coloured glass on a multi-material printer, or one of the one-nozzle options.
    4. Download and print flat, glass face down, with no supports.

    Printers

    Which printing method suits your printer

    MethodWhat printsPrinter
    Coloured glassEvery glass colour in its own translucent filament, with opaque cameMulti-material: a filament changer or tool changer
    One-colour glassOne translucent sheet, then a colour change to opaque came on topAny printer
    Came onlyThe came on its own, with open cells to fill with tinted resinAny printer

    A colour change pauses the print and swaps the filament for every layer above it. Coloured glass sits side by side in the same layers, so it needs a printer that can switch filaments within a layer.

    Options

    Shapes, designs and sizes

    OptionChoicesDefault
    ShapeCircle, arch window, rectangle, hexagon, heartCircle, 140 mm
    DesignRose window, sunflower, butterfly, diamonds, mountain sunrise, or your pictureRose window
    Glass0.4–1.6 mm thick0.8 mm
    Came1.2–4 mm wide, 1.2–5 mm tall1.6 mm wide, 2.4 mm tall
    HangingLoop, suction-cup hole (measured), or none4 mm loop
    Papel picado flag50–180 mm wide, 70–240 mm tall, 0.6–2 mm thick90 × 120 mm, 1 mm

    Printing

    Printing tips

    • Translucent filament: translucent PLA or PETG lets the most light through. PETG is usually the clearer of the two.
    • Clearer glass: print the glass at 100% infill in straight lines, slowly, with 1–2 walls. Gaps and air pockets scatter light.
    • Glass face down: the side on the bed is the smoothest and faces the window.
    • Dry filament: damp PETG prints cloudy and stringy.
    • Papel picado: each flag is one colour and prints flat; thin cord or embroidery thread runs through the channel in the top hem.

    Papel picado

    Papel picado banners

    Papel picado is Mexican cut-paper art: tissue paper cut into lace-like patterns and strung into banners for celebrations, including Día de Muertos altars. This version prints each flag as a thin plastic sheet that lasts for many parties. Pick a pattern (or mix them), spell a word with one letter per flag, and the generator cuts the shapes out, adds stencil-style bridges so the middles of letters stay put, and runs a channel along the top for the string.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits, and your picture never leaves this device.

    Will it fit my printer?

    Choose your printer below the preview. A suncatcher has to fit in one piece, so lower the width if it doesn’t. Banner flags spread over as many plates as needed, one file per plate.

    Can I sell suncatchers and banners I print?

    The designs you make here are yours, and the built-in designs and patterns were drawn for this generator. If you use a picture, use only art you made, bought a licence for, or have permission to use. The typefaces are open-licensed, which allows making physical products.

    Can I print the colours on a printer with one nozzle?

    Not side by side. Choose One-colour glass for a translucent sheet with the came on top (one colour change), and paint the cells with transparent glass paint if you want colour. Or choose Came only and fill the cells with tinted resin.

    Why did some small pieces become came?

    Glass narrower than the came lines would be covered by them, so very small pieces are filled in with came. For pictures, raise Smallest piece or make the suncatcher bigger.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Glass effect? Tips for 3D printing with transparent filaments QIDI Tech
    2. Color change Prusa Research
    3. Multicolor printing with a Prusa: beginner’s guide Prusa Research
    4. Remembering the dearly departed: Day of the Dead celebration Smithsonian Magazine
    5. SIL Open Font License SIL International