Free generator · Runs in your browser

Bird house and feeder generator Right bird, right box.

Make a nest box sized for the bird you hope to see, from published guidance for European and North American species: the right entrance hole, floor and depth, with drainage, vents, an overhanging roof and easy cleaning. Or make a seed, suet, window or nectar feeder.

  • Free and privateNothing leaves this device
  • 15 speciesSizes from published guidance
  • No supportsBox upright, panels flat
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

What to make

Make

Sets the entrance hole, floor, inside depth and hole height from published guidance (see the table below). Check which birds nest near you.

Measure or look up the values for your bird. Inside sizes, in millimetres.

32.0 mm
140 mm
140 mm
200 mm
165 mm

Kept below the roof. A high hole keeps the young out of reach of predators.

Size and details

Roof
35 °
15 °
51 mm

NestWatch suggests 2–4 in (51–102 mm) over the front to keep out driving rain.

15 mm

NestWatch suggests 2 in (51 mm); less keeps the roof on a small bed.

6 mm

6 mm keeps a small box light. For wooden boxes the BTO asks for at least 15 mm, for insulation: for more, make the wall thicker and choose an insulated wall.

Wall

Two 1.6 mm skins with sealed air cells between them, joined by thin webs. It keeps an air layer whatever your slicer’s infill, but uses about as much plastic as a solid wall of the same thickness printed with 15% infill. Use 10 mm or more.

Cleaning access

Two 16 mm holes on each side, as NestWatch suggests, as well as the gap under the roof.

A small ladder below the hole helps the young climb out.

Print as

Flat panels slot together with tabs. Pick your printer below the preview and panels bigger than its bed are cut into as few tiles as it allows, joined by 45° scarf joints that you glue face to face.

Extra 30 mm strips to glue across every joint on the inside, for more strength. More pieces to print.

Mounting
8.0 mm

Measure your screws: the keyhole is 0.6 mm wider than the head.

4.0 mm
90 mm
140 mm
12 mm

The openings at the foot of each wall where seed runs into the tray. Larger for big seed.

30 mm

Measure your suet cake, in its wrapper off.

115 mm
115 mm
40 mm
16 mm

Across each diamond. The cage is 1.5 mm bigger than the cake all round.

180 mm
90 mm
110 mm

Measure your suction cups: the cup, and the knob and neck that go through the slots.

45 mm
10.0 mm
5.0 mm
110 mm
22 mm
4
4.0 mm

Copy the port size of a feeder you trust.

Measure your bottle: the outside of its neck, and from the shoulder to the mouth.

28.0 mm
30 mm

Name and trims

The nectar base has no name: its lid is full of ports.

Raised on the front below the hole. Leave empty for none. Flat panels get a plaque to glue on.

Typeface
18 mm

Shrinks to fit the space below the hole.

1.2 mm
Decorative trim

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a nest box that fits the bird

    Each bird needs its own entrance hole: big enough to get in, small enough to keep larger birds out. Pick a species and the generator sizes the hole, the floor, the depth and the hole’s height from published guidance, then adds drainage, ventilation, an overhanging roof, a way in for cleaning and a ladder inside so the young can climb out.

    1. Pick the species, or enter your own measured values.
    2. Choose the roof, cleaning access and mounting.
    3. Print it as one box, or as flat panels for a bigger bird or a smaller printer.
    4. Add a name or house number if you like.
    5. Put it up at the height and facing the guidance gives, before the nesting season.

    Sizes

    Species and their nest box sizes

    SpeciesRegionEntrance holeFloor (inside)Depth (inside)Hole above the floorMount heightFacing
    Blue titEurope25 mmat least 150 mm acrossabout 175 mm at the frontbottom of the hole at least 120–125 mm up2–3 mNorth-east; avoid south-facing sun traps
    Coal titEurope25 mmat least 150 mm acrossabout 175 mm at the frontbottom of the hole at least 120–125 mm up2–3 mNorth-east; avoid south-facing sun traps
    Marsh titEurope25 mmat least 150 mm acrossabout 175 mm at the frontbottom of the hole at least 120–125 mm up2–3 mNorth-east; avoid south-facing sun traps
    Great titEurope28 mmat least 150 mm acrossabout 175 mm at the frontbottom of the hole at least 120–125 mm up2–3 mNorth-east; avoid south-facing sun traps
    Tree sparrowEurope28 mmat least 150 mm acrossabout 175 mm at the frontbottom of the hole at least 120–125 mm up2–3 mNorth-east; avoid south-facing sun traps
    House sparrowEurope32 mmat least 150 mm acrossabout 175 mm at the frontbottom of the hole at least 120–125 mm up2–3 mNorth-east; avoid south-facing sun traps
    Nuthatch (Eurasian)Europe32 mmat least 150 mm acrossabout 175 mm at the frontbottom of the hole at least 120–125 mm up2–3 mNorth-east; avoid south-facing sun traps
    House wrenNorth America1 in (25.4 mm)5 1/2 × 5 1/2 in (140 mm × 140 mm)8 in (203 mm)6–7 in to the hole (we use 6.5 in)5–10 ftAny
    Black-capped chickadeeNorth America1 1/8 in (28.6 mm)5 1/2 × 5 1/2 in (140 mm × 140 mm)8 in (203 mm)6–7 in to the hole (we use 6.5 in)5–15 ftAway from prevailing wind
    Carolina chickadeeNorth America1 1/8 in (28.6 mm)5 1/2 × 5 1/2 in (140 mm × 140 mm)8 in (203 mm)6–7 in to the hole (we use 6.5 in)4–15 ftAny
    Tree swallowNorth America1 3/8 in (34.9 mm)5 1/2 × 5 1/2 in (140 mm × 140 mm)9 in (229 mm)6–7 in to the hole (we use 6.5 in)5–6 ftSouth or east
    Western bluebirdNorth America1 1/2 in (38.1 mm)5 1/2 × 5 1/2 in (140 mm × 140 mm)9 in (229 mm)6–7 in to the hole (we use 6.5 in)4–6 ftEast
    Mountain bluebirdNorth America1 9/16 in (39.7 mm)5 1/2 × 5 1/2 in (140 mm × 140 mm)9 in (229 mm)6–7 in to the hole (we use 6.5 in)4–6 ftEast
    American kestrelNorth America3 in (76.2 mm)11 1/4 in front × 9 5/8 in side (286 mm × 244 mm)17 3/8 in (441 mm)10–12 in to the hole (we use 11 in)10–30 ftSouth or east
    Eastern screech-owlNorth America3 in (76.2 mm)11 1/4 in front × 9 5/8 in side (286 mm × 244 mm)17 3/8 in (441 mm)10–12 in to the hole (we use 11 in)10–30 ftAny

    North American holes, floors, depths, heights and facing are from the Cornell Lab’s NestWatch species pages; the hole’s height above the floor from University of Missouri Extension. European holes are from the BTO; the floor, the hole height and the mounting height from the BTO’s nest box guide. We left out the eastern bluebird because the hole size on its page did not match the other bluebirds, so we could not confirm it. Starlings, owls of Europe, ducks and swifts need boxes outside this generator’s range.

    Details

    What a good nest box has

    • No perch: NestWatch says a perch “is unnecessary for the birds and can actually help predators gain access”; the BTO and RSPB agree.
    • Drainage: four 10 mm holes in the floor (NestWatch: at least four, 3/8–1/2 in).
    • Ventilation: a gap under the roof, and two 16 mm holes high in each side (NestWatch: two 5/8 in holes per side).
    • An overhanging roof keeps rain off the hole; the BTO adds that it makes it harder for cats to reach in.
    • Cleaning access: the BTO asks for a roof that opens fully; NestWatch shows a hinged side. Choose a lift-off roof or a side door on two screws.
    • A rough inside below the hole: NestWatch: “a series of shallow horizontal cuts, like a small ladder” helps nestlings climb out.
    • A high hole: the BTO wants the hole at least 12 cm above the floor, so predators can’t reach in.

    Placing it

    Putting it up and looking after it

    • Height and direction: see the table. In Europe the BTO suggests 2–3 m up, facing north-east, away from south-facing walls that trap the sun.
    • Poles and baffles: NestWatch recommends a metal pole with a baffle, rather than a tree or fence post, to keep climbing predators out.
    • Cleaning: the BTO says to clean boxes out once a year between 1 September and 31 January; the RSPB adds that, in the UK, unhatched eggs may only be removed legally from September to January (August to January in Scotland). Use boiling water, not insecticides.
    • Check local guidance for the birds near you, the right season and the law where you live.

    Printing

    Printing tips

    • Material: ASA or PETG. Prusa describes ASA as “suitable for outdoor use, due to its high UV light and temperature resistance”, and PETG as suitable for “most exterior use (with temperatures below 80 °C)”. PLA softens in sun and heat.
    • Heat: the BTO warns that boxes of thin wood, plastic or metal “may overheat, which is dangerous for birds”. Use thick walls with sparse infill, site the box out of direct sun, and keep the vents open.
    • One box prints upright with no supports; the roof and any door print flat.
    • Panels print flat, inside face up. Tiles meet in 45° scarf joints that print without supports; glue them face to face, and the tabs into their slots, with a glue made for your plastic. Splice plates are optional.
    • Wall thickness: 6 mm keeps a small box near 600 g of filament. Thicker walls, or the insulated wall with sealed air cells, hold more warmth but use more plastic.
    • Holes come out a little small on most printers: check the entrance with a ruler and open it up with a round file if needed.

    Feeders

    The feeders

    FeederWhat you getMeasure
    Seed feederA square hopper in a drained tray, with seed gaps at the foot and a lid held down by the hanging cordNothing; set the hopper size
    Suet holderA diamond-mesh cage, open at the top, with a lid held by the cordYour suet cake
    Window feederA drained tray on a back plate with two keyhole slots for suction cupsYour suction cups
    Nectar feeder baseA basin, three cord fins, and a lid with feeding ports and a collar for an upside-down bottleYour bottle’s neck

    We make no claims about food or food safety for printed plastic. Keep feeders clean and dry, and follow the advice of a bird organisation near you on what and when to feed.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A small box prints in one piece on most printers. For a bigger bird, pick Flat panels: every panel bigger than your bed is cut into tiles with glued scarf joints, and the pieces are packed onto as few plates as possible.

    Why is there no perch?

    Nest box guidance from NestWatch, the BTO and the RSPB says birds don’t need one, and that a perch helps predators and other birds get at the nest.

    Can I sell boxes I print?

    The designs you make are yours, and nest boxes and feeders are traditional shapes anyone may make. The typefaces are open-licensed, which allows making physical products. There are no claims beyond that.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Right Bird, Right House (species nest box pages) NestWatch, Cornell Lab of Ornithology
    2. Features of a Good Birdhouse NestWatch, Cornell Lab of Ornithology
    3. Nest Boxes for Wildlife (G9413) University of Missouri Extension
    4. Make a nest box British Trust for Ornithology
    5. Nest boxes: your essential guide British Trust for Ornithology
    6. All about nest boxes RSPB
    7. Bird boxes (making a nest box) Worcestershire Wildlife Trust
    8. ASA Prusa Research
    9. PETG Prusa Research