Free generator · Runs in your browser

Sound wave art generator Hold the moment.

Turn a voice message, a baby’s heartbeat or your first dance into 3D printable sound wave art: a plaque, a round record, a keychain, a bookmark, a desk stand, a bracelet or a ring.

  • Nothing uploadedYour sound stays on this device
  • Seven shapesFrom rings to wall plaques
  • No supportsEvery shape prints as laid out
  • Ready to sliceSTL, 3MF and per-colour files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Sound

The microphone is used only while you record, after your browser asks you. Recordings stop after 60 seconds.

Sample: Spoken phrase
0.0 %

Drag to skip silence or a cough at the start. The seconds used show above.

100.0 %

Wave

Style
110

More bars show more detail but come out thinner. The advice below checks them against your nozzle.

70 %

How much of each bar’s space is solid; the rest is the gap between bars.

One connected piece, so no short bar can come loose. The desk stand always has it.

Loudness
10 %
20 %

Raises soft sounds so a whisper still shows next to a laugh.

Shape

Make
150 mm
60 mm

For the desk stand, the height of the wave itself.

120 mm
Round style
165 mm

Measure round the wrist bone with a strip of paper or a soft tape, then measure the strip.

12 mm

Added to the wrist measurement so the cuff sits loosely. Adjust after a test print.

28 mm

The gap the wrist slips through, measured straight across.

Size by
8.00
57.0 mm
18.10 mm
22.0 mm
3.0 mm

The plate, or the band’s wall.

1.6 mm
Wave

Words

Names, a date or a song title. Rings and bracelets have no caption.

Typeface

Colours

Used to check that the bars are wide enough to print.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    Make sound wave art in four steps

    The generator measures how loud the sound is from moment to moment and draws that as bars or an outline: loud parts stand tall, pauses go flat. The sound is read by your browser and never sent anywhere.

    1. Choose the sound. Upload a voice message, a song or a video, record one, or try a sample.
    2. Trim it to the words or the beat you want.
    3. Pick a shape: a plaque, a round record, a keychain, a bookmark, a desk stand, a bracelet or a ring.
    4. Add a caption, download and print.

    Shapes

    Shapes and starting sizes

    ShapeStarting sizePrints
    Plaque150 × 60 mm, optional frame and QR codeFlat, no supports
    Round record120 mm across; grows outward or mirroredFlat, no supports
    Keychain70 × 24 mm with a ring holeFlat, no supports
    Bookmark140 × 34 mm, 0.8 mm thinFlat, no supports
    Desk standA 140 mm wave in a slotted baseTwo flat pieces, no supports
    BraceletC-shaped cuff from your wrist measurementOn its side, no supports
    RingUS or EU (ISO 8653) sizeOn its side, no supports

    Every size can be changed. Bracelets are made from your own wrist measurement, not a standard size.

    Good sounds

    Getting a wave that reads well

    • Short is better: two to ten seconds of speech, or one line of a song, gives clear separate words.
    • Trim the silence at both ends so the wave fills the space.
    • Peak keeps every sharp sound; Average gives a calmer, rounder wave.
    • Lift quiet parts if a soft voice comes out flat next to a laugh or a clap.

    Printing

    Printing tips

    • Bar width: keep bars at least as wide as your nozzle (the advice checks it). Fewer bars print sturdier.
    • Two colours on one nozzle: raised waves on flat shapes take a colour change at the plate’s thickness.
    • Backlit: print the base in white or natural PLA at 100% infill and light it from behind.
    • Bracelets: PETG or TPU flexes open more safely than PLA.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Is my recording uploaded?

    No. The sound is read by your browser on this device and only the shape of the wave is used. The microphone is used only when you press Record and your browser asks you.

    Will it fit my printer?

    Choose your printer below the preview. If it is too big, lower the width or diameter.

    Can I sell what I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. If you use someone else’s song or voice, that sound is theirs, so ask first.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. BaseAudioContext: decodeAudioData() method MDN Web Docs
    2. MediaRecorder MDN Web Docs
    3. Ring size (US and ISO 8653 sizes) Wikipedia
    4. Color change Prusa Research
    5. SIL Open Font License SIL International