Free generator · Runs in your browser

Advent calendar generator A drawer for every day.

Make a drawer cabinet, a Christmas-tree tower, a little house or a set of stacking boxes, with every drawer sized to the treat you measure, numbered, and split into pieces that fit your printer.

  • Private by designNothing leaves this device
  • Four stylesCabinet, tree, house, boxes
  • No supportsDrawers print open side up
  • Ready to sliceFits your bed, plate by plate

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Style

Style
24

24 for 1–24 December; 25 to include Christmas Day; 12 for twelve days.

Start at 13 for a calendar that counts 13 to 24, for example.

Without it, the boxes stack on each other, lid to base.

6

Rows follow from the number of days. A column count that divides it evenly leaves no empty cells.

Number order

Drawers

Measure the biggest treat or gift that goes in one drawer. Wrapped chocolates and small toys vary a lot, so measure yours.

1.0 mm

Added on every side and on top, so it drops in and lifts out easily.

Pull

A small ramp on each drawer clicks past a lip at the front of its cell, so drawers don’t slide out by themselves.

0.30 mm

Gap between each drawer and its cell (or each lid and its box), per side. Print the fit test to check it.

For stacking boxes, one box and its lid. Print this first, in the same filament, to check the clearance before the whole calendar.

Numbers and names

Numbers
0.8 mm
Typeface

Siblings can share one calendar: each drawer takes the next name in turn.

Up to six names of 14 letters each. Short names stay readable on small drawers.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make an advent calendar

    Measure what goes in each drawer, pick a style and the number of days, and the generator sizes every drawer and cell to fit, adds the numbers and lays everything out on your printer’s plates.

    1. Measure one treat: width, depth and height, in millimetres.
    2. Pick a style and the number of days.
    3. Choose your printer below the preview, so big frames split into pieces that fit.
    4. Print the fit test, adjust the clearance, then print the calendar.
    5. Fill and close the drawers in number order, or mix them up.

    Styles

    The four styles

    StyleWhat it isPrints as
    Drawer cabinetA grid of numbered pull-out drawers in a frameFrame on its back, drawers open side up
    Christmas treeRows of drawers, one fewer each row, on a trunk with a nook, and a star on topEach row is its own piece; stack and glue them
    HouseA house front with numbered drawers, a gable roof with a nook and roof trimFrame on its back, drawers open side up
    Stacking boxesA numbered box with a plug-in lid for every day, on a tray or stackedBoxes open side up, lids top down

    Fit

    The tolerance test

    Printers differ, so the gap a drawer needs to slide differs too. Lab guides for desktop printers suggest starting around 0.2–0.4 mm per side for sliding parts, then testing. The default here is 0.3 mm.

    1. Turn on Fit test and print the single cell and drawer, in the filament you’ll use.
    2. If the drawer sticks, raise Fit clearance by 0.05–0.1 mm; if it rattles, lower it.
    3. Or print a tolerance test to find your printer’s smallest gap that slides freely, and use that.

    Printing

    Printing tips

    • No supports: drawers print open side up; frames lie on their back, so every cell is an open pocket. Knobs are teardrops, with 45° undersides.
    • Frame cells are closed at the back, so drawers stop flush with the front.
    • Click stop: the ramps sit on thin side walls that flex a little. PLA and PETG both work; if a drawer is hard to pull out, turn the stop off or raise the clearance.
    • Big frames: pick your printer and the frame splits into pieces with their own walls. Glue them side by side.
    • Numbers: raised numbers are their own part for a second filament. Cut-in numbers can be filled with paint.
    • Treats: keep food wrapped. Printed layers are hard to clean, so prints aren’t a food-safe surface.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A frame too big for the bed splits into pieces that fit, and the drawers spread over as many plates as needed. The readout shows how many plates.

    Can I sell calendars I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Drawers and boxes are small parts, so check toy-safety rules before selling for children.

    How do I choose the drawer size?

    Measure the biggest thing that goes in one drawer. The generator adds the room you choose around it, then the walls, then the fit clearance for the cell. The readout shows the inside size you get.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-11. Community posts are one maker's experience, not a specification.

    1. Design the clearance and tolerance UAL Creative Computing Institute
    2. Food safe FDM printing Prusa Research
    3. Color change Prusa Research
    4. SIL Open Font License SIL International