Free generator · Runs in your browser

Ring sizer generator Find the fit, then print the ring.

Print a ring sizer set in your own size range, with every size engraved, plus a sizing stick, a finger gauge strip, engraved rings, stacking rings and bangles. Sizes follow the published US, UK and European rules.

  • Private by designNothing leaves this device
  • Your size rangeUS, UK letters or EU sizes
  • No supportsEverything prints as laid out
  • Ready to sliceEvery band its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Make

Make

Plain test bands, one per size, each with its size engraved. Try them on to find your size.

A tapered stick marked with sizes. Slide a ring you already own down it and read the size at its lower edge.

A flexible strip, best printed in TPU. Loop it round your finger, push the tail through the slot and read the size in the slot.

A simple band with initials or a date, inside or out, or a stack of thin rings. For a spinner ring, use the fidget ring generator.

A closed bangle or an open C-cuff, sized from your own measurement.

Size

Size system
5.0
10.0
48 mm
62 mm
Steps
Steps
Steps

Up to 24 bands in one set.

7.00

Each whole size is 0.81 mm wider inside.

54.0 mm
Style

A bangle has to slide over your hand. Tuck your thumb into your palm and measure around the widest part, across the knuckles.

Measure around your wrist where the cuff will sit, without pulling the tape tight.

200 mm

Measure your own hand or wrist with a soft tape or a strip of paper. The value shown is only a starting point.

5 mm

Added to your measurement for the inside circumference. Printed plastic barely stretches, so allow a little.

25 mm

The gap the cuff goes on through, sideways over the narrow part of the wrist.

Shape

5.0 mm

Wide bands fit tighter. Make the sizers about as wide as the ring you plan to wear.

1.4 mm

A slightly domed inside that slides over the knuckle more easily. The size is measured at the middle.

Keep the set together
0.40 mm
7.0 mm

More space makes a longer, gentler taper that is easier to read.

12.0 mm
1.0 mm

The marks allow for the strip bending round your finger, so keep the printed thickness true.

6.0 mm

Wide bands fit tighter: above about 6 mm, many jewellers suggest half a size up.

1.8 mm
1

Several thin rings of the same size to wear together.

14 mm
2.6 mm
Profile

Text

Sizes are engraved for you.

Initials, a name or a date. For a stack, give each ring its own text with | between them: A | B | C.

Engraved inside, readable from the inside.

Outside text
0.40 mm
Typeface

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to find your ring size with a printed sizer

    Pick a size system and a range, and the generator makes one plain test band per size, with the inside diameter taken from the published size rule and the size engraved on the outside. A tab on each band takes a key ring, so the set stays together.

    1. Print one known size first and measure its inside with calipers, or check it against a ring that fits. Printers often make holes a little small.
    2. Print the set in the same filament and settings.
    3. Try them at the end of the day, when fingers are at their largest. The right size slides over the knuckle with a little resistance and doesn’t spin loosely.
    4. Check with a jeweller before you buy an expensive ring. A printed sizer is a good guide, not a jeweller’s gauge.

    Sizes

    Ring sizes

    US sizeInside diameterInside circumferenceNearest UK letterNearest ISO size
    314.07 mm44.2 mmF½44.2
    414.88 mm46.8 mmH½46.8
    515.69 mm49.3 mmJ½49.3
    616.51 mm51.9 mmL½51.9
    717.32 mm54.4 mmN½54.4
    818.13 mm57.0 mmP½57.0
    918.95 mm59.5 mmR½59.5
    1019.76 mm62.1 mmT½62.1
    1120.57 mm64.6 mmV½64.6
    1221.38 mm67.2 mmX½67.2
    1322.20 mm69.7 mmundefined69.7

    US and Canadian sizes grow by 0.032 in (0.81 mm) of inside diameter per size. UK, Irish and Australian letters grow by 1.25 mm of inside circumference per letter, with size C at 40 mm. A European (ISO 8653) size is the inside circumference in millimetres. Japanese sizes don’t follow a simple published rule, so they aren’t offered.

    Other sizers

    The sizing stick and the gauge strip

    • Sizing stick: slide a ring that fits down the stick until it stops, and read the mark at its lower edge. The smooth surface at each mark has exactly that size’s diameter. Print it standing up; it needs no supports.
    • Gauge strip: print it in TPU so it bends. Loop it round the finger with the marks outside, push the tail through the slot and pull it snug. The size in the slot is your size. The marks allow for the strip’s thickness as it bends.
    • Bracelets: a closed bangle must slide over the hand, so measure around the knuckles with your thumb tucked in. For a cuff, measure the wrist.

    Printing

    Printing tips

    • Same material, same settings: a sizer is only as true as the print. Use the filament and settings you’ll print the ring in.
    • Wide bands fit tighter: make the sizers about as wide as the ring you plan to wear.
    • Layers: 0.12–0.16 mm gives smooth insides and crisp engraving.
    • No supports: bands, the stick and the strip all print flat or upright as laid out.
    • Small parts: sizer bands and rings are a choking hazard. Not for children under 3.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A large set spreads over as many plates as it needs, one file per plate.

    How accurate is a printed ring sizer?

    Close, if your printer is: the inside of each band is drawn to the exact diameter, but prints often come out a little small. Print one known size first and measure it. Before buying an expensive ring, have your finger sized by a jeweller.

    Can I sell rings or sizers I print?

    The designs you make are yours, and ring sizes are public measurements anyone may use. The typefaces are open-licensed, which allows making physical products. Rings and sizer bands are small parts, so check toy-safety rules before selling anything for children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Ring size (US, UK letters and ISO 8653 sizes) Wikipedia
    2. How to Size a Ring: 4 Easy Steps for Perfect Fit Jewelers Touch
    3. How to Measure Your Bangle Size at Home jewellerybox
    4. SIL Open Font License SIL International