Free generator · Runs in your browser

Toy car track generator Race day, printed.

Design track for 1:64 die-cast cars: straights, curves, ramps, jumps, banked turns, crossings and a start gate, with lanes sized to your own cars and connectors that join flat.

  • Private by designNothing leaves this device
  • Twelve piecesOr a whole layout at once
  • No supportsEvery piece prints flat
  • Ready to sliceEvery piece its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Track

Make

Separate pieces with commas. Add “right” to turn right (“curve right”) and “x3” to repeat (“straight x3”). Each piece starts where the last one ends.

Turns
1

Several copies are shown joined end to end, and all of them are laid out to print.

Car and lanes

Lanes
30.0 mm

Measure your widest car across its wheels or body, whichever is wider. 1:64 die-cast cars vary because each is made to fit a standard box, not an exact scale.

4.0 mm

Added to both sides of the car to make the lane width.

75 mm

Sets the space behind the start gate.

40 mm

Front axle to rear axle. With the ground clearance it sets how gently ramps bend.

2.0 mm

The gap under the middle of your lowest car.

Instead of dashed lines. Keeps drag racers in their own lane.

8 mm
2.4 mm

Pieces

Sizes for every piece of that kind, in a layout or on its own.

150 mm
150 mm

To the middle of the track.

Curve angle
170 mm
60 mm
40 mm
200 mm

The sloped part, between the flat connector ends.

25 mm
20 °
100 mm

Where the next piece starts, for the preview and diagram.

160 mm
Banked curve angle
15 °

Eases in and out, so both ends join flat track.

12 °
40 mm

To the underside of the deck. In a layout, pillars match the height the ramps climb to.

41.0 mm

For the adapter: measure the outside width of your strip with calipers. The starting value is only a placeholder, not a standard size.

1.6 mm
0.30 mm

Markings and joints

On the start gate and behind it.

Optional: a track name, a race or a child’s name.

Typeface
0.15 mm

How much smaller each dog-bone connector is than its socket, all round. Raise it if connectors are too tight to press in.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a toy car track

    Measure your car, pick your pieces, and the generator sizes the lanes, bends and ramps to it, adds a dog-bone socket per lane at every joint, and lays every piece, pillar and connector out on your printer’s plates.

    1. Measure your widest car (width, length, wheelbase and the gap under it). The lane is the car plus room each side.
    2. Build a layout: type the pieces in order, or tap the buttons to add them. The diagram numbers each piece.
    3. Personalise it: lane lines, START and FINISH, lane numbers, a name on the gate.
    4. Download and print. Pieces print flat with no supports; join them with the connectors.

    Pieces

    The pieces

    PieceYou setNotes
    StraightLengthFlat, sockets at both ends
    CurveRadius, 30° to 180°Left or right
    S-bendLength and sideways shiftMoves the track over without turning it
    Ramp up or downRise and lengthRound bends sized for your car; a solid wedge
    Jump rampLip height and angleEnds in a lip; the gap sets where the next piece goes
    Banked curveRadius, angle, bankingBanking eases in and out to join flat track
    CrossingSquare, all four ends socketedTwo tracks cross at 90°
    Y-splitTwo parallel exitsSplits one run into two, or merges two
    Start gateSlopeBack wall, lane numbers, a lift-out gate with your name
    Finish lineFixedChequered line, FINISH and a stop wall
    Support pillarsHeightA footed column with a cradle for the deck
    Flexible-track adapterMeasured strip width and thicknessPockets the strip slides into

    Sizes

    Fitting your cars

    Die-cast cars sold as 1:64 are not all the same size: most are made to fit a standard blister pack, so a small hatchback and a big pickup come out at different scales. That is why the generator asks for your own car’s measurements instead of assuming one.

    • Lane width is your car’s width plus the room each side. Four millimetres a side suits most cars; a wobbly car needs more.
    • Ramps bend no tighter than wheelbase² ÷ (8 × ground clearance), plus a margin, so a car’s middle clears the top of a slope.
    • Adapter: flexible strip tracks differ by maker and age, so measure your strip’s width and floor thickness with calipers and print the adapter first to test it.

    Printing

    Printing tips

    • No supports: every piece prints on its flat underside. Ramps, jumps, the start gate and banked curves are wedges hollowed by narrow tunnels with 45° pointed roofs, so they need no supports or bridges; pillars print standing up.
    • Connectors: print a few first. If they don’t press in, raise the connector clearance by 0.05 mm.
    • Two colours: lane lines, words and numbers are their own part. On one nozzle, print them in the track colour and paint the raised lines.
    • Smooth running: a 0.2 mm layer height and a gentle top-surface ironing pass give a faster deck.
    • Small parts: connectors and loose gates are small enough to swallow, so keep them away from children under 3.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Pieces, pillars and connectors spread over as many plates as needed; if a piece is bigger than the bed, lower its radius, angle or length.

    Can I sell tracks I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Connectors are small parts, so check toy-safety rules before selling for children.

    Will it work with my existing track?

    The adapter joins this track to a flexible strip track whose width and thickness you measure. It is not made to any maker’s published size, so print the adapter on its own first.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-11. Community posts are one maker's experience, not a specification.

    1. 1:64 scale (box scale) Wikipedia
    2. Breakover angle Wikipedia
    3. Modeling with 3D printing in mind Prusa Research
    4. Color change Prusa Research
    5. Small parts for toys and children’s products US Consumer Product Safety Commission
    6. SIL Open Font License SIL International