Free generator · Runs in your browser

Bag clip generator Keep it fresh.

Make bag clips that fit your bags: a one-piece clip with a U spring and a snap hook, a pin-hinge clip with a lock ring, a slide-on rail or a spring peg. Measure the bag, add a label or a whole pantry set, and a fridge magnet.

  • Private by designNothing leaves this device
  • Four clip typesHook, ring, rail and peg
  • No supportsEverything prints flat
  • Ready to sliceEvery clip its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Clip

Type

The classic: two arms joined by a U spring, printed open. Squeeze it shut and the hook on one tip snaps over the other. One piece.

Two flat arms on a print-in-place hinge. Fold it over the bag and slide the ring on to lock it. Prints as a clip and a ring.

Lay the bag top over a rod and slide a C channel along it. No spring to wear out. Prints as a channel and a rod.

Like a clothes peg: two levers rock on a fulcrum and a printed C spring snaps round them. Prints as three pieces.

100 mm

Shut, from end to end. Make it a little longer than the bag is wide.

10 mm

How much of the bag the jaws cover, front to back. 10–12 mm suits most bags.

6.0 mm

Thicker arms bend less, so long clips grip along their whole length.

3.0 mm
8.0 mm

Grip

Measure one layer of the bag with calipers. Bags differ a lot: a thin snack bag and a foil-lined coffee bag can be several times apart. Too thin to measure? Measure 10 layers and divide by 10.

Layers in the jaws

A flat bag top is two layers. Fold or roll it and the jaws hold more.

0.10 mm

Taken off the gap, so the jaws press the bag. The jaw gap is the layers times the thickness, less this.

0.6 mm

How much narrower the spring is than the levers it wraps. More presses harder.

Grooves on both jaws, half a step apart, so the bag can’t slide out.

Spring

1.6 mm

Stiffness grows with the cube of this: 2 mm is about twice as stiff as 1.6 mm. The readout gives a relative estimate.

14 mm

The thin legs behind the jaws. Longer is softer and kinder to the plastic.

20 °

The arms print open by this angle. It grows if arm B would not clear the hook.

1.2 mm

How far the hook reaches over the other arm. More holds harder but needs more push to close.

0.30 mm

The gap between parts that move. 0.3 mm suits most printers.

The rail clip has no spring: the channel holds the bag round the rod.

Label

One clip per line, for a pantry set.

Make several of every item, such as spares or a whole plate of one name.

Check every clip

    One per line, up to 30. Add | for a second line, and an order number in square brackets to name each object without printing it: [1042] Olivia | Class 3. Pick your printer below the preview to fill its plates.

    Typeface
    7.0 mm

    Arm B widens into a panel when the letters need room. Long words shrink to fit.

    Lettering

    On the pin-hinge clip the label is cut into the underside of an arm, which faces up when shut, so it is always engraved.

    0.6 mm
    0.6 mm

    Extras

    A pocket 0.3 mm wider than the magnet, on the back of the clip. Measure yours with calipers.

    The peg’s levers are too thin for a magnet pocket.

    A 5 mm hole to hang the clip on a hook or pegboard.

    Preview

    Download

    Building the preview…

    Print it well

      Everything is built on this device. Nothing you type or upload is sent anywhere.

      Advertisement

      The method

      How to make a bag clip

      Pick a clip type and a length, measure your bag, and the generator sets the jaw gap, cuts ribs into the jaws, sizes the spring and lays every clip out flat on your printer’s plates.

      1. Pick a type: a one-piece hook clip, a pin hinge with a ring, a slide-on rail or a peg.
      2. Measure the bag with calipers and choose how many layers the jaws hold.
      3. Add a label, or a list of labels for a pantry set, and a magnet or a hanging hole.
      4. Download and print flat. No supports.

      Types

      Which clip?

      TypeHow it holdsPrints asBest for
      Hinge and hookA U spring opens it; a hook on one tip snaps over the otherOne piece, open in a VChips and snack bags, everyday use
      Pin hinge and ringA print-in-place hinge; a ring slides on to lock itA clip and a ringWide, flat clips and pantry sets
      Slide-on railThe bag wraps round a rod; a C channel slides over itA channel and a rodLong bags and rolled tops: no spring to wear out
      Spring pegLevers rock on a fulcrum; a C spring presses the jaws shutTwo levers and a springQuick one-handed use

      Sizes

      Sizes and settings

      SettingDefaultWhy
      Jaw gapLayers × measured thickness, less the squeezeBags vary too much for one standard, so you measure yours
      Squeeze0.1 mmPresses the bag a little; raise it for slippery film
      Spring1.6 mmThin enough to flex, thick enough to spring back; stiffness grows with its cube
      Hook overlap1.2 mmHolds without needing a hard push to close
      Clearance0.3 mmThe gap between moving parts that most printers keep open
      Magnet pocketMagnet + 0.3 mmRoom for the magnet and a drop of glue

      Printing

      Printing tips

      • Material: PETG is tough and flexes without breaking, which suits springs and hooks. PLA is stiff and brittle: a PLA clip works, but its spring and hook can crack after a while, and PLA softens above about 60 °C.
      • Print flat, as laid out. The spring then bends along its layers, the strong way.
      • Walls, not infill: 3 or more walls make the spring solid perimeter. More walls add more strength than more infill.
      • First layer: elephant’s foot can fuse the pin hinge’s knuckles; turn on its compensation or work the hinge free gently.
      • Food: clip the folded bag, not the food. Printed plastic isn’t a food-safe surface: layer lines trap crumbs and are hard to clean.

      Questions, answered

      Is it free to use?

      Yes. No account, no watermark, no limits.

      Will it fit my printer?

      Choose your printer below the preview. Long clips lie along the bed; a pantry set spreads over as many plates as it needs, one file per plate.

      How strong is the clip?

      The readout gives the spring’s stiffness compared with the default clip, not a force. Try the clip on your bag; if it slips, raise the squeeze, fold the bag once more or thicken the spring.

      Is a printed clip food safe?

      We don’t claim it is. The clip should hold the folded top of the bag, away from the food. If it might touch food, wrap the food first.

      Can I sell clips I print?

      The designs you make are yours, and bag clips like these are common household items anyone may make. The typefaces are open-licensed, which allows making physical products. Rings, springs and magnets are small parts, so check toy-safety rules before selling for children.

      Sources

      Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

      1. PETG Prusa Research
      2. PLA Prusa Research
      3. Food safe FDM printing Prusa Research
      4. Layers and perimeters Prusa Research
      5. Elephant foot compensation Prusa Research
      6. How to design living hinges for 3D printing Hubs
      7. Living hinge: design guidelines and material selection MatterHackers
      8. SIL Open Font License SIL International