Free generator · Runs in your browser

Geodesic dome and connector generator Plan it, cut it, print the hubs.

Plan a 1V to 4V geodesic dome for dowels, rods, pipes or straws: the cut list, every strut length and count, and a printable hub of every type with sockets along the true strut directions. Or print simple connectors for STEM kits.

  • Private by designNothing leaves this device
  • Whole-dome planCut list and hub counts
  • True anglesSockets along every strut
  • Ready to sliceEvery hub its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Shape

Make
Frequency

Higher frequency: more, shorter struts and a rounder dome.

How much of the sphere
How much of the sphere
How much of the sphere
How much of the sphere

Measured through the hub centres. 1200 mm is 1.2 m.

Connector
5
10 °

0° keeps every socket in one plane; more makes a dome-like or tent-like hub.

8

A cube needs 8 corners; a tetrahedron needs 4.

Struts

Strut shape
12.0 mm

Measure the dowel, rod, pipe or straw with calipers: diameter for round, width for square. Sizes vary from batch to batch.

0.30 mm

Added to the strut size. 0.2–0.4 mm suits most printers; print one hub first to check the fit.

20 mm
2.4 mm

Hubs

A small screw or pin through the wall holds the strut. Leave off for straws or a push fit.

3.0 mm
4.5 mm

For a screw or tent peg through each base hub’s foot.

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to plan and build a geodesic dome

    Pick a frequency and how much of the sphere you want, set the diameter and measure your struts. The generator works out every hub and strut, groups the struts by length (A, B, C…) and the hubs by type, and gives you a cut list and a print file with every hub.

    1. Choose the dome: frequency, 1/2, 3/8 or 5/8, and the diameter.
    2. Measure the struts with calipers and enter the size. Print one hub and test the fit before printing the rest.
    3. Cut the struts to the lengths in the cut list. Label each strut with its letter.
    4. Assemble by matching each hub’s engraved letter to the plan. The letter faces the inside of the dome.

    Frequencies

    Struts and hubs for each dome

    DomeStrut lengthsStrutsHubs (4-, 5-, 6-way)
    1V full sphere13012 five-way
    1V dome1255, 6, 0
    2V full sphere21200, 12, 30
    2V 1/2 dome26510, 6, 10
    3V 3/8 dome312015, 6, 25
    3V 5/8 dome316515, 6, 40
    4V 1/2 dome625020, 6, 65

    Strut length = chord factor × sphere radius, measured hub centre to hub centre. The cut length takes off the distance from each hub centre to the bottom of its socket. Our letters run from shortest (A) to longest, so they may not match the letters in other tables. On the 3V 3/8 and 5/8 domes the base ring zig-zags slightly; each base hub’s foot is made to reach one flat ground plane.

    Printing

    Printing tips

    • Supports: the sockets lean out from the centre, so turn on supports touching the build plate only (tree supports work well). Hubs print outer face down, base hubs foot down.
    • Test first: print one hub, push in a strut, and change the clearance by 0.1 mm if it is too tight or loose.
    • Strength: 4 walls and 30% infill make stiffer sockets. PETG copes with sun and heat better than PLA outdoors.
    • Screw holes point up as printed, so they come out round. Drill through the strut with the hub in place.

    Safety

    What printed hubs are for

    Printed hubs are for models, play frames and light covers, not for climbing, shelters or carrying loads. We make no claim about how much any hub can hold. Keep a fabric cover light and take the dome down in wind. Hubs and connectors are small parts: not for children under 3.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Each hub is small. Choose your printer below the preview and every hub is packed onto as many plates as needed, with a file per plate.

    Can I sell domes or kits I print?

    The designs you make are yours, and geodesic domes are a long-public idea anyone may build. Hubs and connectors are small parts, so check toy-safety rules before selling kits for children, and make no load claims.

    Why do the strut letters differ from other tables?

    We letter struts from shortest to longest. The lengths and counts are the same as the published chord-factor tables; only the names change.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Geodesic dome formulas (chord factors and counts) Desert Domes
    2. 3V dome calculator (3/8 and 5/8 counts) Desert Domes
    3. 2V dome calculator Desert Domes