Free generator · Runs in your browser

Stamp generator Mirrored for you.

Turn a monogram, a logo or any picture into a 3D printable stamp: a wax seal, a cookie stamp with its cutter, a clay maker’s mark, an ink stamp on a mount or an embosser pair. The face is mirrored automatically.

  • Private by designArt and text stay on this device
  • Mirrored automaticallyPreview the impression first
  • Five stamp typesWax, dough, clay, ink, paper
  • Ready to sliceSTL and multi-part 3MF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Stamp type

Make a

A small head with the design cut into its face, so the wax stands up.

A raised design on a plate with a plunger handle, and a matching cutter.

A raised or cut-in maker’s mark on a block handle.

A thin raised face for flexible filament, and a rigid mount with an index on top.

Two matching plates that press a raised design into paper or leather.

Preview

Impression shows what the stamp leaves, reading the right way round. Downloads are always the stamp.

Design

In the middle

One to four short lines. Fewer, bigger letters stamp best.

90 %

How much of the free space the text or picture fills.

4.0 mm

Letters shrink on their own if the words are too long to fit.

Typeface

Shape and size

Face
30 mm

The longer side of the face. Wax seal heads run from 20 to 40 mm.

0.60 ×
1.0 mm

Relief

Design

Cut in is the usual wax seal: the design stands up in the wax. Raised inverts it.

1.2 mm

About 1–1.5 mm for wax and ink, 2–4 mm for dough and clay.

12 °

Leans the relief walls. Tapered walls let go of wax, dough and clay more easily and make thin lines stronger.

Used to check the thinnest line in your design.

Handle and parts

22 mm
50 mm
8.0 mm

For an ink stamp this is the whole face plate, relief included: 2–3 mm bends well in flexible filament.

Cuts the cookie around the stamped mark.

1.0 mm
14.0 mm

A block with a shallow recess for the face plate and a finger groove.

Shows which way up the stamp is.

0.30 mm
0.40 mm

Measure your paper, card or leather. The hollow plate is widened by this much.

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    Shortcuts

    Start from your kind of project

    The same studio opens ready for each of these: Wax seal generator · Custom stamp maker.

    The method

    Make a custom stamp in four steps

    Type a monogram, bend words around a circle, or add your own picture or SVG. The generator lays the design out as it should read, then builds the stamp with its face mirrored, so the mark comes out the right way round. Everything is traced and built on your device.

    1. Pick the stamp type: wax seal, cookie, clay or soap, ink, or an embosser pair.
    2. Add the design and choose the face shape and size.
    3. Check the impression. Switch the preview to Impression to see what the stamp leaves, and read the thinnest-line check.
    4. Download and print face up, with no supports.

    Stamp types

    Five kinds of stamp

    TypeThe facePartsGood to know
    Wax sealCut in, so the wax stands up; raised to invertHead on a turned handle, in one piece or push-fitWax is hot: see the heat notes below
    Cookie or fondantRaised, 2–4 mmPlate on a plunger handle, plus a cutter ringSee the food notes below
    Clay or soapRaised or cut inHead on a block handleA maker’s mark for pots, tiles and soap bars
    Ink stampRaised, on a 2–3 mm plateFlexible face plate and a rigid mount with an indexFor a flat ink pad; not self-inking
    Embosser pairOne raised plate, one hollowTwo plates lined up by two pinsWidened by your material’s thickness; try scrap first

    Every face can be round, square, a rectangle or an oval, or it can follow the outline of the art.

    Mirroring

    Why the stamp looks backwards

    A stamp has to be a mirror image of its mark, the way a rubber stamp’s letters run right to left. You lay the design out the readable way; the generator flips every printed face for you. The ink stamp’s index and the raised embosser plate are the two places where the design is meant to be read directly, so those are not flipped.

    Use the Impression preview to see the mark itself: wax and cut-in stamps leave a raised design, raised stamps leave a sunken one, and ink stamps print the raised parts.

    Design

    Relief depth, draft and thin lines

    SettingRangeWhat it does
    Relief depth0.4–5 mmHow far the design stands up or is cut in. Deeper marks need softer material: dough and clay take 2–4 mm.
    Draft angle0–30°Leans the relief walls outward towards the plate. The stamp releases more easily and thin lines sit on a wider foot.
    Thinnest lineMeasured from your artCompared with two passes of your nozzle: 0.8 mm for a 0.4 mm nozzle. Thinner lines may not print solid.
    Border ring0.4–3 mmA ring just inside the edge of the face, 0.6 mm in from the rim.

    If the check says the lines are too thin, make the face bigger, pick a bolder typeface, use fewer words or fit a finer nozzle.

    Wax seals

    Hot wax and printed plastic

    Sealing wax goes on hot, and common filaments soften with heat. Prusa’s material guides say PLA gets soft and deforms above 60 °C, PETG suits use below 80 °C, and ASA resists up to 93 °C.

    • Chill the stamp. Makers rest the head on ice or in cold water between seals, then dry it, so the wax sets fast and the plastic stays cool.
    • Pick a warmer-rated filament for regular use: ASA or another high-temperature material, or a metal-filled filament.
    • Let the wax settle for a few seconds before pressing, and test on a spare blob first.
    • Push-fit heads let you reprint just the head in another material or with another design.

    These are makers’ tips, not a rating: we have not tested any filament against any wax.

    Cookies and fondant

    Using printed stamps with food

    Printed plastic is not like a metal stamp. Layer lines trap dough, and bacteria can grow in them, so Prusa recommends treating printed kitchen tools as items you replace after some use.

    • Keep contact short and wash by hand in warm water. PLA softens above about 60 °C, so no dishwasher.
    • Nozzle matters: brass nozzles can contain lead; a stainless steel nozzle is preferred for food items.
    • "Food-safe" filament describes the raw material, not your finished print, which is never certified.

    Ink stamps

    Flexible face, rigid mount

    • Face plate: print it in flexible filament (TPU), design up. Prusa’s guide suggests printing flexible materials slowly, around 20 mm/s, with little retraction.
    • Mount: any rigid filament. It prints top down, so the index is cut into the first layer and the recess faces up.
    • Assemble: glue or tape the plate into the recess, then turn the block over: the index on top shows the design the right way round and which way is up.
    • Ink pads: use a flat pad larger than the face. This is a hand stamp; it does not fit self-inking frames.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits, and your text and pictures never leave this device.

    Will it fit my printer?

    Stamps are small, so almost any printer fits one. Choose your printer below the preview to check; the tallest part is the handle.

    Do I have to mirror my design first?

    No. Lay it out so you can read it. The generator mirrors the face, and the Impression preview shows the result.

    Can I sell stamps I print?

    The stamp designs you make are yours. The typefaces are open-licensed, which allows making physical products. The artwork is the part to check: only use logos and pictures you made, bought a licence for, or have permission to use. We make no safety or food-contact claims for printed stamps, so check the rules where you sell.

    Can I use an SVG?

    Yes. Your browser draws the SVG, then it is traced like any picture: dark or opaque areas become the design.

    Why did my small text disappear?

    Lines thinner than about two passes of the nozzle do not print solid. Read the thinnest-line figure under the preview, then make the stamp bigger or the text shorter and bolder.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-11. Community posts are one maker's experience, not a specification.

    1. PLA (gets soft and deforms above 60 °C) Prusa Research
    2. PETG (use below 80 °C) Prusa Research
    3. ASA (temperature resistance up to 93 °C) Prusa Research
    4. Flexible materials Prusa Research
    5. Food-safe FDM printing Prusa Research
    6. Modeling with 3D printing in mind Prusa Research
    7. Make your own seal stamp and wax (cold-water tip) Instructables, community guide
    8. SIL Open Font License SIL International