Free generator · Runs in your browser

Cable clip and organizer generator Sized to your cables.

Measure your cables and make clips that snap on and stay, a desk edge holder for chargers, an under-desk raceway cut to fit your printer, cord wraps, labels and a desk grommet.

  • Private by designNothing leaves this device
  • Seven organizersClips to grommets
  • No supportsLaid out to print as is
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Make

Make
3

One slot per cable. Each slot has its own diameter below.

Measure across the cable with calipers, at a round part away from the plug. Flat cables: use the wider side.

0.8 mm

The snap-in mouth is the cable diameter minus this. More grip holds tighter but is harder to press in.

0.30 mm

The round hole is the cable diameter plus this, so the cable can slide.

Coil the cable as you store it, squeeze it gently and measure across the bundle.

Measure the hole in your desk with calipers or a ruler across its widest point.

0.4 mm

The sleeve is this much smaller than the hole.

0

Pick your printer below the preview: pieces are cut to fit its bed. Without one, they fit a 220 mm bed.

Mount

Fix it with

Head sizes from DIN 7997. For other screws, choose Measured and measure the head and shank.

Measure your adhesive pad; the back plate is made big enough to carry all of it.

Drop-lock pegs for pegboards with upright 5 × 15 mm slots on a 40 mm pitch. The cables run up and down the board.

Nothing to fix: this one needs no mount.

Size

12 mm
3.0 mm
2.0 mm

Thinner walls flex more easily; thicker ones grip harder.

16 mm

Make it wider than your widest plug so plugs sit side by side.

24 mm
18 mm
2.0 mm
3.0 mm
2.5 mm

Inward lips along the top; push cables past them. 0 for an open channel.

20 mm

A gap in one wall at the middle of each piece, where cables come out. 0 for none.

30 mm
0.30 mm

Each joiner is this much narrower than the inside on each side, so it slides in.

14 mm
1.8 mm
70 mm
34 mm
3.0 mm
1.6 mm
6.0 mm
16 mm

How far it reaches into the hole. Keep it shorter than the desk is thick.

14 mm
0.30 mm
1

Copies are laid out together; pick your printer to fill its plates.

Labels

Separate labels with commas or new lines, up to 24. Each becomes its own tag.

7.0 mm
0.8 mm

Uncontracted braille, sized like the braille label generator’s sign dots. For personal use; not for ADA signs.

Typeface

Labels are their own item: choose Cable labels under Make.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make cable clips that fit

    Printed cable clips are usually one fixed size. Here you measure your own cables and every slot is made to fit: a round hole a little bigger than the cable, and a mouth a little narrower, so the cable snaps in and stays.

    1. Pick what to make: clips, a desk edge holder, a raceway, a cord wrap, an earbud winder, labels or a grommet.
    2. Measure each cable with calipers, and your desk, pad, hole or screws where asked.
    3. Set the grip and the fixing.
    4. Download and print as laid out, with no supports.

    Sizes

    What you measure, and what it sets

    ItemYou measureIt sets
    Clip slotCable diameterHole = cable + clearance; mouth = cable − grip allowance
    Desk-edge clampDesk thicknessGap between the jaws = desk + clamp clearance
    Desk edge holderCable diametersKeyhole slots: plugs bigger than the hole can’t pull through
    RacewayLength you needPieces that fit your bed, joined inside by U joiners
    Cord wrapCoiled cable diameterStrap length, with a hole either side to adjust
    Cable labelCable diameterThe clip’s hole and mouth
    GrommetDesk hole diameterSleeve = hole − fit; a cap with a cable slot

    Defaults are only starting points: there is no standard cable size, so measure yours. Most charging cables are a few millimetres thick; power cords are thicker.

    Fixings

    Screw hole sizes

    ScrewHead (DIN 7997)Clearance holeCountersink
    3 mm5.6 mm3.5 mm6.2 mm
    4 mm7.5 mm4.5 mm8.1 mm
    5 mm9.2 mm5.5 mm9.8 mm
    6 mm11 mm6.5 mm11.6 mm
    3.5 mm6.5 mm4.0 mm7.1 mm
    4.5 mm8.3 mm5.0 mm8.9 mm

    Head diameters are the nominal sizes in DIN 7997 for countersunk wood screws. The hole is 0.5 mm bigger than the thread and the countersink 0.6 mm bigger than the head. Adhesive pads: measure yours, and the back plate is sized to carry it. Pegboard pegs fit upright 5 × 15 mm slots on a 40 mm pitch.

    Materials

    Which filament for which part

    • TPU for cord wraps: the strap has to bend round the coil and stretch over the button. A rigid filament will crack.
    • PETG for clips under strain: snap-in clips and clamps flex every time you use them. PETG bends further before it breaks than PLA and creeps less.
    • PLA is fine for labels, the raceway and the grommet, away from heat.
    • Small parts: clips, labels and winders are small enough to swallow. Not for children under 3.

    Printing

    Printing tips

    • As laid out, no supports: clips stand up so the layers run round each ring; clamps and the desk edge holder lie on their side; the raceway lies base down with 45° lips; labels lie flat with a 45° foot under the clip; the grommet prints flange down, so its top face is the smooth bed side.
    • Test one first: print one clip, check the fit on your cable, then change the grip or clearance by 0.1–0.2 mm and print the rest.
    • Two colours on labels: the raised text is its own object in the 3MF, or pause at its first layer to swap filament.

    Safety

    Keep power cords in the open

    Organizers are for tidying, not hiding. Leave power bricks, chargers and extension cords out in the open: don’t pack them tightly into a raceway or tray, or bundle them under something. A state fact sheet on extension cords says not to cover an extension cord with anything other than a cord protector, not to overheat one, and not to fix one to a wall with nails or staples (see the sources). We make no fire or load claims for these parts.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A long raceway is cut into pieces that fit its bed; copies and labels fill as many plates as needed.

    How do I get the fit right?

    Measure the cable with calipers. If a cable is hard to press in, lower the grip allowance; if it falls out, raise it. Print one test clip before a whole set.

    How much will it hold?

    We don’t give load ratings. Clips hold cables, not weight: don’t hang anything heavy from a printed clip or raceway, and test the fixing first.

    Is the braille compliant?

    No. It is uncontracted (Grade 1) braille for personal and household use. The ADA requires contracted (Grade 2) braille on signs. Ask a braille reader to check labels that matter.

    Can I sell what I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. We make no claims about load, fire or safety, so test anything you sell and don’t promise more than you have tested.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. DIN 7997: cross-recessed countersunk head wood screws, dimensions fasten.it
    2. boxes.py slot pegboard generator (slot layout) Florian Festi
    3. Slot pegboard network mounts (drop-lock peg geometry) PrimroseHA (GitHub)
    4. Flexible materials Prusa Research
    5. PETG Prusa Research
    6. Extension cord safety fact sheet Texas Department of Insurance
    7. 2010 ADA Standards, 703.3 Braille US Access Board
    8. Size and spacing of braille characters Braille Authority of North America
    9. SIL Open Font License SIL International