Free generator · Runs in your browser

Moon lamp generator The Moon, at any size.

Make a Moon lamp, a Mars or Earth relief globe, or a photo sphere from public NASA and USGS maps: sized to your light, with a foot or a stand, whole or in two halves.

  • Private by designYour photo never leaves this device
  • Real NASA mapsMoon, Mars and Earth
  • Sized to your lightA measured opening and a cord notch
  • Ready to sliceWatertight STL and 3MF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Globe

Make
World
Pattern

Surface brightness shows the dark seas and bright craters you see in the sky. Height shows mountains and basins; on Earth, the land glows and the seas stay dark. Mars has height only.

Place it

All the way round suits a 2:1 panorama or a world map.

100 °

How far round the sphere the picture reaches.

Around it

Size and wall

100 mm

Pick your printer below the preview to check it fits.

0.8 mm

Keep at least two lines of your nozzle: 0.8 mm suits a 0.4 mm nozzle.

3.0 mm

Thicker gives deeper shadows but needs a brighter light.

Pattern on
10 ×

×1 is true scale, which is almost smooth at this size.

Inside
2.0 mm

Light and base

Measure your LED puck or LED tea light across its widest point and add about 1 mm. Hollow globes only.

Stands on
50 mm

Wider stands steadier. It is never smaller than the opening plus a rim.

A notch at the back so the globe sits flat over a light with a cable.

6.0 mm

Measure your cable and add a little.

Print

For bigger globes or no-support printing. Hollow globes only.

0.20 mm

Gap on each side of the ring. Print a tolerance test if unsure.

0 °

The point of the map that faces the front. North is positive.

0 °

East is positive. 0° faces the Moon’s near side and Africa on Earth.

Download detail
Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a Moon lamp

    A Moon lamp is a hollow sphere whose wall is thin where the Moon is bright and thick where it is dark. Lit from inside, the seas and craters glow through the plastic. This generator builds it from NASA’s own maps, so you can make one at any size without downloading a model of hundreds of megabytes.

    1. Pick a world (Moon, Mars or Earth) or add your own photo.
    2. Set the diameter and the thinnest and thickest walls.
    3. Measure your light and enter the opening it needs.
    4. Choose a foot or a stand, and halves for large globes.
    5. Download and print in white PLA, solid, with fine layers.

    Options

    Lamp, relief globe or photo

    MakeWhat changesBest for
    Lamp (lithophane)Wall thickness, 0.8–3 mm by defaultA night light that shows the map when lit
    Relief globeThe outside rises with real height, ×1–×80A desk globe; looks good in colour
    Your photoYour picture on the front, the Moon or plain around itGifts; a 2:1 panorama can wrap all the way round
    SettingRangeNotes
    Diameter60–200 mmLarger shows more detail; check your printer’s height
    Thinnest / thickest wall0.6–2 / 1.6–5 mmFrom our lithophane generator: 0.8 and 3 mm suit a 0.4 mm nozzle
    Opening10–90 mmMeasure your light; add about 1 mm
    HalvesJoining ring, 0.1–0.5 mm clearanceBoth halves print rim-down

    The maps

    Where the maps come from

    The Moon uses the Lunar Reconnaissance Orbiter’s camera mosaic and laser altimeter heights, from NASA’s CGI Moon Kit. Mars uses the Mars Global Surveyor laser altimeter elevation map from the USGS. Earth uses NASA’s Blue Marble image and a topography map made from GEBCO data. Each is a small 1024 × 512 greyscale copy that ships with this page, so nothing large is downloaded.

    Relief heights are scaled from each world’s range: about 20 km on the Moon, about 30 km on Mars and sea level to 8.8 km on Earth (oceans are flat). At ×1 they are true to scale, which is almost smooth at desk size.

    Printing

    Printing tips

    • Filament: white or natural PLA lets the most light through.
    • Infill: 100% (solid) on lamps, so no infill pattern shows once lit.
    • Layers: 0.12–0.16 mm smooth the gradients.
    • Whole sphere: stands on its foot; the lower part leans out, so slow the start. The readout shows the steepest angle.
    • Halves: both print rim-down, usually without supports; the ring joins them.
    • Light: LED only. PLA softens with heat, so never use a candle or a hot bulb.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A whole globe needs a printer as tall as its diameter; halves need only about half that.

    Can I sell lamps I print?

    The designs you make are yours. The NASA maps are not protected by copyright in the United States and the USGS Mars map is public domain (CC0); credit NASA and USGS where you can. A photo you upload must be one you have the right to use.

    Why is the file smaller than other Moon lamp models?

    The detail is capped near the resolution of the maps (about 1,000 pixels around), which keeps files to tens of megabytes. Pick Fine for large globes.

    Does it need supports?

    Halves usually print without supports. A whole sphere leans out near its foot; the advice under the preview gives the angle and says when to add supports from the build plate.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. CGI Moon Kit (colour and elevation maps) NASA Scientific Visualization Studio
    2. Mars MGS MOLA DEM 463 m USGS Astrogeology Science Center
    3. Blue Marble Next Generation with topography and bathymetry (April) NASA Earth Observatory
    4. Topography (GEBCO data) NASA Earth Observatory
    5. Images and media usage guidelines NASA
    6. Moon fact sheet (radius) NASA
    7. Mars fact sheet (radius) NASA
    8. Topography of the Moon Wikipedia
    9. Geography of Mars Wikipedia
    10. How to 3D print a lithophane: a beginner’s guide Sovol
    11. PLA material guide Prusa Research