Free generator · Runs in your browser

Celtic knot generator Over, under, over.

Draw Celtic knotwork on a grid or pick a trinity, heart, circular, eternity or shield knot, and print it with a true woven over-under: coasters, trivets, pendants, borders, rings and inlays.

  • Private by designNothing leaves this device
  • Real weaveBands rise over and dip under
  • Draw your ownClick edges to add breaks
  • Ready to sliceSTL and 3MF, a part per strand

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Knot

Make

Square knot panels are drawn on the grid below; the others are built for you.

4
4
Symmetry while you click

Click an edge between two cells: once for a wall along it, twice for a wall across it, three times to clear it. Strands bounce off walls instead of crossing. With the grid focused, the arrow keys move between edges, E jumps to the edge at right angles, and Space or Enter changes the edge.

The same grid as text, one line per row, for typing a design or pasting one in. On an edge, . means strands cross, - is a level wall and | an upright wall. Corners are +.

8

How many times the pattern repeats round the circle.

3
Pattern

A circle passing over and under the three loops.

Heart
4

More cells give a busier knot.

4

One endless strand with this many loops.

2

The shield is woven on a square grid this many cells across, with a loop at each corner.

100 mm

Across the knot’s longest side (or diameter).

“My grid design” repeats the square knot you draw with the Square knot panel design, edge to edge.

2

Size

The strip is split into pieces that fit your printer (pick it below the preview). Each piece ends at a full break, so no band is cut.

30 mm

Measure the inside of a ring that fits, or for a bangle the widest part of your hand with the thumb tucked in. The inside will be this size exactly.

14.0 mm

From edge to edge along the finger or wrist.

1.6 mm
4.5 mm

The width of each strand. It is narrowed if the design has no room for it.

0.70 mm

The space left either side of the strand that passes over.

2.6 mm

Style

Weave

3D weave: each band rises over its crossings and dips where it goes under. Flat: even bands with a gap at each under-crossing.

A groove down the middle of every band, for the classic outlined look.

3.0 mm
Backing shape
5.0 mm
1

For a coaster set. They are laid out on your printer’s plates.

Separate round feet that press into sockets under the backing, so hot pots sit off the table.

12.0 mm
5.0 mm

Holes in the margin above the knot, for a wall panel. The top margin grows to fit them.

4.5 mm

A border joined to the outer bands. Added anyway if strands would otherwise fall apart.

3.0 mm
5.0 mm

For a jump ring or a cord.

2.0 mm
0.20 mm

Added round the knot on every side of the channel. Print a small one first to check the fit.

0.6 mm

Colours

Each separate strand becomes its own part (up to four colours, then they repeat). One-piece knots, inlays and pendants print in one colour.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How a Celtic knot is built on a grid

    This generator uses the grid method described by Christian Mercat and by Peter Cromwell. Take a grid of cells. Every edge between two cells is a crossing point, and the strands run diagonally from edge to edge round each cell, crossing at every edge. With no walls you get a plain plait. A break (a wall) on an edge stops the strands crossing there: they bounce off it instead, which makes the loops and turns of real knotwork.

    1. Pick what to make and a knot design, or draw one: click edges on the grid to add walls. Symmetry copies each click so the design stays balanced.
    2. Set the size, band width and height.
    3. Choose the weave: 3D, where bands rise over and dip under, or flat bands with gaps.
    4. Colours: one for the knot, or one per strand. The readout counts the strands for you.
    5. Download STL or 3MF and print it flat, knot side up.

    The weave alternates over, under, over along every strand, as in traditional knotwork. Such alternating designs can always be drawn this way, which is why the method works on any grid, a circle or a heart.

    What you can make

    Modes and what you get

    MakeYou getPrints as
    Panel on a backingCoaster, coaster set, trivet with feet, wall panel with hanging holesBacking and knot, one part per strand colour if you like
    Cut-throughThe knot alone, joined under each crossing so it is one pieceOne part, one colour
    PendantA cut-through knot with a loop at the topOne part
    Border stripA strip of knotwork of any length, cut into pieces at full breaksBacking and knot pieces, laid out on your printer’s plates
    Ring or braceletA border wrapped round a ring of your inside diameterRing and knot, standing on its edge
    InlayA backing with a channel and a separate knot that presses into itTwo parts in two colours

    Settings

    Sizes and options

    SettingWhat it doesStarting point
    Knot sizeLongest side or diameter of the knot40 mm pendant, 86–100 mm coaster, 150–180 mm trivet
    Band widthWidth of each strandAbout a third of a grid cell; narrowed if there is no room
    GapSpace each side of the strand on top at an under-crossing0.6–0.8 mm
    Band heightHow far the knot stands up2–3 mm on a backing, 3–4 mm cut-through
    Inside diameter (rings)Exact inside size of the ringMeasured, not a standard size
    Clearance (inlays)Room round the knot in the channel0.2 mm, then adjust

    For a ring, measure a ring that fits you or use our ring sizer. Wide bands fit more snugly than narrow ones, so allow a little more for a wide ring.

    Printing

    Printing tips

    • Knot side up, no supports for panels, cut-through knots, pendants, borders and inlays.
    • Colour per strand: load the 3MF and each strand colour is its own part; swap filament at the backing’s top layer for a simple two-colour print.
    • Rings and bracelets print standing on their edge. Bands that run level round the ring make short overhangs, which most printers manage; add supports if yours struggles.
    • Fine bands: keep bands at least twice your nozzle width (0.8 mm with a 0.4 mm nozzle). A 0.25 mm nozzle helps on small pendants.
    • Trivets: PLA softens at about 60 °C. Use PETG or ASA for warm dishes, and test with your own pans; we make no heat rating.
    • Pendants and small knots are small parts: not for children under 3.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview to check. Border strips and coaster sets are laid out on its plates automatically.

    Why does the readout say several strands?

    The grid decides how many separate closed strands the knot has. A plain plait of 4 × 4 cells has 4; a 3 × 4 plait has 1. Breaks join or split strands. Turn on “A colour for each strand” to see them.

    Will a cut-through knot fall apart?

    No. Each strand runs on under the one above it as a low link, so every crossing joins them. If a strand never crosses the others, a frame (and if needed a short tie) is added so the print is one piece.

    Can I sell what I print?

    The designs you make are yours. Celtic knotwork is a traditional style free for anyone to use. We make no claims beyond that, so check anything you sell, such as heat use for trivets.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-13. Community posts are one maker's experience, not a specification.

    1. Celtic knotwork: the ultimate tutorial (walls) Christian Mercat
    2. Celtic Knotwork: Mathematical Art Peter R. Cromwell, Springer
    3. On the Topology of Celtic Knot Designs Bridges 2004
    4. PETG Prusa Research