Free generator · Runs in your browser

Board game insert generator Everything in its place.

Measure your game box and list what goes in it: cards, tokens, dice, meeples, money and loose bits. Get a packed plan of trays and lidded boxes that sit flush under the board, with spacers for the gaps, ready to print.

  • Private by designNothing leaves this device
  • A whole insertTrays, boxes and spacers packed in layers
  • No supportsEverything prints upright as laid out
  • Ready to sliceEach container its own named object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Game box

Measure the inside of the box bottom, not the outside: wall to wall, and from the floor to the top edge.

250 mm
250 mm
70 mm
12.0 mm

Stack the folded board, the rulebook and any player boards on the table and measure their height. The insert stops below them.

1.0 mm

Room left between the insert and the box, half on each side. 0.5 to 1 mm lets it drop in without forcing.

Height grid

Containers are one, two or three grid steps tall, so stacks always end at the same height. Two or three layers let small trays stack on top of each other.

Components

6

Each row becomes a container. A row of cards can hold several stacks.

Component 1

Engraved on the container. Short words print best; leave it empty for none.

Cards in each stack; tokens, dice, figures or tiles in all.

2

Separate piles of this card, each with its own slot.

Cards
Shape

Measure 10 stacked and divide by 10.

4

5 and 7 round up to a full grid of 6 and 8.

Measure your largest die across its widest point.

Measure the largest figure, base included.

The space the bits need, like a bag of them pressed flat. Measure it.

Component 2

Engraved on the container. Short words print best; leave it empty for none.

Cards in each stack; tokens, dice, figures or tiles in all.

1

Separate piles of this card, each with its own slot.

Cards
Shape

Measure 10 stacked and divide by 10.

4

5 and 7 round up to a full grid of 6 and 8.

Measure your largest die across its widest point.

Measure the largest figure, base included.

The space the bits need, like a bag of them pressed flat. Measure it.

Component 3

Engraved on the container. Short words print best; leave it empty for none.

Cards in each stack; tokens, dice, figures or tiles in all.

1

Separate piles of this card, each with its own slot.

Cards
Shape

Measure 10 stacked and divide by 10.

4

5 and 7 round up to a full grid of 6 and 8.

Measure your largest die across its widest point.

Measure the largest figure, base included.

The space the bits need, like a bag of them pressed flat. Measure it.

Component 4

Engraved on the container. Short words print best; leave it empty for none.

Cards in each stack; tokens, dice, figures or tiles in all.

1

Separate piles of this card, each with its own slot.

Cards
Shape

Measure 10 stacked and divide by 10.

4

5 and 7 round up to a full grid of 6 and 8.

Measure your largest die across its widest point.

Measure the largest figure, base included.

The space the bits need, like a bag of them pressed flat. Measure it.

Component 5

Engraved on the container. Short words print best; leave it empty for none.

Cards in each stack; tokens, dice, figures or tiles in all.

1

Separate piles of this card, each with its own slot.

Cards
Shape

Measure 10 stacked and divide by 10.

2

5 and 7 round up to a full grid of 6 and 8.

Measure your largest die across its widest point.

Measure the largest figure, base included.

The space the bits need, like a bag of them pressed flat. Measure it.

Component 6

Engraved on the container. Short words print best; leave it empty for none.

Cards in each stack; tokens, dice, figures or tiles in all.

1

Separate piles of this card, each with its own slot.

Cards
Shape

Measure 10 stacked and divide by 10.

4

5 and 7 round up to a full grid of 6 and 8.

Measure your largest die across its widest point.

Measure the largest figure, base included.

The space the bits need, like a bag of them pressed flat. Measure it.

Packing plan

The plan appears here once the preview is built.

Fit and labels

Added to every component’s width, depth and stack height.

Press 20 cards together with calipers and divide by 20.

Measure a sleeve’s width and take away the card’s width. It adds the same to the height.

Measure 10 sleeved cards, divide by 10, and take away the card thickness.

1.6 mm

Engraved labels need 1.4 mm or more. Lidded boxes use at least 1.6 mm, or 2 mm with a sliding lid.

1.2 mm

On the front or end of each tray, and on the lid of each box.

Typeface

Colours and view

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to plan a board game insert

    Measure the box and list what goes in it. The generator sizes a container for each component, packs them into the box in layers, fills the gaps with hollow spacers and lays everything out on your printer’s plates.

    1. Measure the inside of the box with a ruler or calipers: wall to wall and floor to rim. Outside sizes include the cardboard and will not fit.
    2. Measure the board and rulebook stacked on the table: the insert stops that far below the rim, so the lid closes flat.
    3. Add a row per component: cards, tokens, dice, figures, money or tiles, or a space for loose bits. Measure their sizes and thicknesses.
    4. Check the packing plan. It shows each layer from above and lists anything that does not fit. Try a different container, fewer stacks or another height grid.
    5. Download and print. Every container, lid and spacer is its own object in the 3MF, named after its label.

    Containers

    Which container to choose

    ContainerBest forHow it worksPrints
    Card tray, standingDecks you draw from oftenCards stand on edge, a slot per stack, with a finger notch through the wallsUpright
    Card tray, lyingLow boxes and big stacksCards lie flat side by side, a notch in front of each stackUpright
    Token trayCoins, tokens, moneyCompartments with scooped floors, so a finger slides tokens outUpright
    Dice trayDiceOne scooped compartmentUpright
    Box with a sliding lidFigures, tiles, small partsA lid that slides out of 45° groovesBox upright, lid flat
    Box with a snap-fit lidMeeples and loose bitsBumps on the lid click into a grooveBox upright, lid upside down
    SpacerEmpty spaceA hollow open block that stops the rest from slidingUpright

    Sizes

    Sizes and settings

    SettingDefaultWhat it does
    Play1 mmTaken off the box size: half on each side and above the insert
    Gap between containers0.4 mmSo each container lifts out on its own
    Clearance1 mmAdded to every component’s size and stack height
    Card stackCards × thickness + clearanceThe slot depth for a standing stack, or the depth for a lying one
    Height grid1, 2 or 3 layersContainers are whole grid steps tall, minus 0.3 mm so stacks lift apart

    Card sizes come from a card printer’s published table:

    CardSize
    Standard63 × 88 mm
    Japanese small59 × 86 mm
    Poker63.5 × 88.9 mm
    Bridge57.15 × 88.9 mm
    Tarot70 × 120 mm
    Mini42 × 63.5 mm

    Token, dice, figure and sleeve sizes vary between games and makers, so the generator asks you to measure them. The numbers in the presets are examples only.

    Printing

    Printing tips

    • No supports: trays and boxes print upright as laid out; engraved labels and finger notches need none.
    • Test one tray first: print the smallest container and check your cards or tokens fit before printing the rest.
    • Big spacers: they are cut into pieces that fit your printer’s bed. Pick your printer below the preview so the pieces match it.
    • Fast filament use: spacers can print with fewer walls and little infill; they only fill space.
    • Lids: if a lid is tight, sand the lip lightly or print it again with the box generator at a larger clearance.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Containers and lids are laid out on as many plates as they need, and big spacers are cut to fit the bed. A container bigger than the bed is flagged so you can make it smaller.

    Can I sell inserts I make?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Don’t put game names or other companies’ logos on inserts you sell.

    Why does it ask me to measure so much?

    Boxes, cards, sleeves and tokens differ between games and printings. An insert made from your own measurements drops in and holds the pieces without rattling; one made from guesses often does not.

    Something does not fit. What can I change?

    Try a lying card tray instead of a standing one, fewer stacks per row, more compartments for tokens, or another height grid. The plan lists each component that does not fit and why.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Playing Card Dimensions PrintNinja
    2. Modeling with 3D printing in mind Prusa Research
    3. SIL Open Font License SIL International