Free generator · Runs in your browser

Christmas tree topper generator Made to fit your tree.

Make a star, a 3D slotted star, a snowflake, an angel, a bow, a lattice or stained-glass star, or a family name under a star, on a socket sized to your tree’s tip, with room for a battery LED light.

  • Private by designNothing leaves this device
  • Eight stylesStars, angel, bow, name
  • No supportsFlat topper, upright socket
  • Fits your tipMeasured, balanced socket

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Topper

Style
Star
9 %

How high the facets rise at the centre, as a share of the star’s height.

Points
Snowflake

A short word reads best: a family name, Joy, Noel.

Typeface
1.2 mm
18
3

Each number gives a different arrangement of cells.

2.6 mm
Glass
180 mm

The topper’s height, without the socket.

5.0 mm

Thinner is lighter on the tip; 4–6 mm is stiff enough for most sizes.

Tree tip

Mount

Measure your tree’s top stem where the socket will end (about 4–5 cm below the very top). Wrap a strip of paper round it, mark the overlap, and divide the length by 3.14.

Measure about 1 cm below the very top. The socket tapers between the two.

45 mm
0.6 mm

Added to the tip’s diameter. Raise it if the socket will not slide on.

Six thin ribs that crush a little, so the socket holds firmly.

0.6 mm
0.5 mm

How much smaller than the tip the fingers close, each side.

Measure your cable ties or wire.

0.30 mm

Extra room in the socket’s slot for the topper’s tab, and in the slots where a 3D star’s halves cross.

Light

Light

Measure your battery LED: a fairy-light bulb, or the whole LED puck.

0.30 mm

For the groove on the back and the channel down the socket.

Translucent panels fill the openings of the flat, lattice and stained-glass stars. Put a battery LED light behind them.

0.8 mm

For stained glass and glowing panels: thin glass lets more light through.

Battery LED lights only. Never use a mains bulb, an incandescent bulb or a candle in a printed topper.

Print

Pieces
0.25 mm

Split if needed uses the printer you pick below the preview.

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a tree topper that fits

    Bought toppers rarely fit the tip of your own tree. Measure the tip once, and the generator sizes the socket to it, puts the socket under the topper’s centre of mass so it stands straight, and lays every piece out for your printer.

    1. Pick a style and its height.
    2. Measure the tip in two places: about 1 cm and 4–5 cm below the very top. Wrap a strip of paper round it, mark the overlap, and divide the length by 3.14.
    3. Choose a mount: a tapered socket, a spring clip, a coil, or a bar to tie on.
    4. Add a light if you like: a pocket for a battery LED, or glowing panels.
    5. Download and print. The topper prints flat and the socket on its head, with no supports.

    Mounts

    Ways to fix it to the tree

    MountBest forHow it holds
    Cone socketMost treesA bore that tapers like the tip, your tip plus a clearance, with optional crush ribs. It grips tips across a range of sizes.
    Spring clipTips of uneven sizeFour slotted fingers, a little smaller than the tip, spring open and squeeze. Print it in PETG.
    Spiral coilThin or bendy tipsA coil wound to the tip’s taper twists on like a spring. It needs supports to print.
    Tie-on barThick or odd tips, real treesA flat bar below the topper with slots for cable ties or florist wire.

    Styles

    Styles and sizes

    StyleWhat it isLight
    Star5, 6 or 8 points: flat, puffy with facets, or two layersPocket or panels (flat)
    3D slotted starTwo flat stars that slot together at right anglesNone
    SnowflakeSix arms with branches: classic, fern or crystalPocket
    AngelA silhouette with a halo and wingsPocket
    BowTwo loops and tailsPocket
    Lattice starA Voronoi web inside a starPocket or panels
    Stained-glass starA frame with glass in two colours, or one sheetPocket or panels
    NameA word or family name on a banner under a starPocket

    Heights run from 100 to 300 mm. Larger toppers are heavier: weigh the tip of your tree in your mind before printing a big one, and keep walls and infill low.

    Printing

    Printing tips

    • No supports: the topper prints flat and the socket stands on its head, so the bore opens upward. Only the spiral coil needs supports.
    • Keep it light: 2 walls and 10–15% infill. The weight shown is for a solid print, so the real one is lighter.
    • Too big for the bed: it splits into two halves with diamond pegs that print without supports. Glue the halves together.
    • Glass: print the glass in translucent filament. With one glass sheet, start in the glass colour and swap to the frame colour at the glass thickness.
    • Lights: battery LED only. Printed plastic softens with heat; PLA softens at around 60 °C.
    • Fit: if the socket is loose, lower the clearance or wrap the tip with tape; if it is tight, raise it.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. If the topper is too big, it splits into two halves joined by pegs, and every piece is laid out on as many plates as needed.

    Can I sell toppers I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. The pegs and lens are small parts, so check the rules for decorations before selling them.

    Can I put a light in it?

    Yes, a battery LED light: a fairy-light bulb or an LED puck in the pocket, or a light behind glowing panels. Never use a mains bulb, an incandescent bulb or a candle.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. CPSC gives consumers a holiday home decorating safety guide U.S. Consumer Product Safety Commission
    2. PLA Prusa Research
    3. PETG Prusa Research
    4. Color change Prusa Research
    5. SIL Open Font License SIL International