Free generator · Runs in your browser

Hinge generator Print it, swing it.

Make a print-in-place hinge that comes off the bed already working, a hinge for a metal pin, a lift-off hinge or a living hinge. Countersunk screw holes, stops at flat or 90°, and a clearance test to tune your printer.

  • Private by designNothing leaves this device
  • Five typesPrint-in-place to living hinge
  • No supportsCones and teardrops at 45°
  • Ready to sliceEach hinge its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Hinge

Type

Prints assembled. Cone pins on one leaf sit in cone sockets on the other, one clearance apart.

The halves print apart. Push a pin through the knuckles: filament, a screw, a nail or a rod.

One knuckle on each leaf. The pin sits snugly in leaf A, and leaf B lifts off it, like a door you can take down.

Two pads joined by a thin strip that bends. Use PP or PETG; PLA cracks after a few bends.

Four small print-in-place hinges with the gap printed on each, from 0.1 mm under your clearance upwards. The smallest one that turns freely is your clearance.

0.30 mm

The gap between moving parts, your printer’s key setting. 0.3 mm suits most printers; print the clearance test to find yours.

Size

40 mm
20 mm

Each leaf, measured from the pin’s centre to the leaf’s outer edge.

Each test hinge is 24 mm long with your knuckle, cone and leaf settings (leaves up to 1.8 mm thick).

2.4 mm

On a hinge with knuckles, keep it under half the knuckle diameter so the leaves fold flat.

8.0 mm
Knuckles

Always odd, so leaf A gets the extra knuckle at both ends.

4.0 mm

The base of the 45° cone pins. It is capped to leave a wall in the knuckles.

Measure a nail, wire or rod with calipers. A printed pin prints standing up.

0.50 mm

0.4–0.6 mm is a good start: two or three layers.

4.0 mm

Fixing

2
Leaf shape
Stop

Flat: a chin under the knuckles stops leaf B folding back past flat. 90°: posts on the knuckles hold it upright, as for a box lid.

Mounting

An offset leaf steps up, so a door that overlaps its frame can close flat. Its raised plate needs supports under it.

6.0 mm

The test hinges have no screw holes.

Preview

Preview
30 °

Turns leaf B in the assembled preview. Downloads are always flat, ready to print.

1

Pick your printer below the preview to fill its plates.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How the hinge is built

    The pin runs along the bed at the height of the knuckle’s radius, so the knuckles stand on the plate and both leaves lie flat beside them. Knuckles alternate between the leaves, always an odd number, with a gap of one clearance between neighbours. Each leaf is cut back where the other leaf’s knuckles turn, so no point of one leaf ever comes closer than the clearance to the other, at any angle.

    On a print-in-place hinge, leaf A’s knuckles end in 45° cones that sit in matching cone-shaped sockets in leaf B’s knuckles, one clearance away all round. A 45° slope is the steepest overhang most printers manage without supports, so the cones, the sockets and the whole hinge print flat and come off the bed already assembled. Pin holes are teardrops, round with a 45° point on top, for the same reason.

    1. Pick a type and set the clearance (print the clearance test first if you don’t know it).
    2. Size it: length, leaf width, thickness and knuckles.
    3. Add screw holes, a stop and a leaf shape.
    4. Download and print flat, as laid out.

    Types

    Which hinge to make

    TypePrintsBest for
    Print-in-placeAssembled, in one goBoxes, lids, flaps and prototypes
    Separate pinTwo halves, then a pin throughStronger hinges: a metal pin takes the load
    Lift-offTwo halves and a pinDoors and lids you want to take off
    Living hingeOne piece with a thin stripSnap lids and flaps in PP or PETG
    Clearance testFour small hingesFinding the gap your printer needs

    Sizes

    Screw holes

    Holes are the medium clearance size for each screw, and countersunk at 90°, 0.4 mm wider than the largest head, so the head sits flush. Metric countersunk heads are 90°; inch wood screws have 82° heads, which still seat in a 90° countersink.

    ScrewHoleLargest headCountersink
    M2.5 machine screw2.9 mm4.7 mm5.1 mm at 90°
    M3 machine screw3.4 mm5.6 mm6.0 mm at 90°
    M4 machine screw4.5 mm7.5 mm7.9 mm at 90°
    M5 machine screw5.5 mm9.2 mm9.6 mm at 90°
    3 mm wood screw3.4 mm5.9 mm6.3 mm at 90°
    4 mm wood screw4.5 mm7.9 mm8.3 mm at 90°
    5 mm wood screw5.5 mm9.6 mm10.0 mm at 90°

    If the leaf is too thin for the head, the countersink stops 0.6 mm above the bed and the readout says how far the head stands proud.

    Pins

    Pins and stops

    • Pin holes are the pin plus the clearance: 1.75 mm filament, a 3 mm or 4 mm screw, or anything you measure. On a lift-off hinge, leaf A’s hole is snug so the pin stays put.
    • Stops flat: a chin under leaf A’s knuckles meets the end of leaf B, so the hinge opens flat and no further.
    • Stops at 90°: posts on top of leaf A’s knuckles hold leaf B upright, like a lid that stays open.
    • Offset leaf: leaf B steps up so an overlapping door closes flat. The raised plate prints over air, so it needs supports touching the build plate under it.

    Printing

    Printing tips

    • Print flat, as laid out, with no supports (except under an offset leaf).
    • First layer: a squashed first layer (elephant’s foot) is what fuses print-in-place knuckles. Turn on elephant’s foot compensation (about 0.2 mm), or level and slow the first layer.
    • Stuck? Work it free gently: flex the leaves a little each way, then further. Don’t force a full fold on the first try.
    • Clearance: 0.3 mm suits most printers; well-tuned ones manage 0.2–0.25 mm.
    • Living hinges: PP lasts longest, PETG well; PLA cracks after a few bends. Bend it once soon after printing, while it is still a little warm.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Long hinges lie along the bed; copies spread over as many plates as needed.

    Why won’t my hinge turn?

    The knuckles fused on the first layer, or the clearance is too small for your printer. Print the clearance test, use the smallest gap that turns freely, and turn on elephant’s foot compensation.

    Will a PLA living hinge last?

    Not for long. PLA is stiff and cracks after a few to a few dozen bends. Polypropylene is the classic living-hinge plastic; PETG and nylon also work. Use the strip to test before you design one into a part.

    Can I sell hinges I print?

    The designs you make are yours, and hinges like these are common hardware anyone may make. Pins and small hinges are small parts, so check toy-safety rules before selling for children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Modeling with 3D printing in mind Prusa Research
    2. Elephant foot compensation Prusa Research
    3. Print-in-place 3D printing: hinges, joints and moving parts Sovol
    4. Metric countersunk machine screws, DIN 965 dimensions Westfield Fasteners
    5. Chipboard screw dimensions Kangaroo
    6. Tapping and clearance hole sizes (ISO 273 series) Optimas
    7. Countersink Wikipedia
    8. ISO metric screw thread Wikipedia
    9. Fused filament fabrication Wikipedia
    10. How to design living hinges for 3D printing Hubs
    11. Living hinge: design guidelines and material selection MatterHackers