Free generator · Runs in your browser

Lamp shade generator Made to fit your lamp.

Design a drum, globe, bell, twisted or pleated shade with a fitter sized to your socket, harp or bulb, check the bulb clearance, and download it ready to print. For LED bulbs only.

  • Free and privateNothing leaves this device
  • Eight shapesFive wall patterns
  • Fits your lampSocket ring, harp, clip, pendant
  • No supportsFitter prints flat

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Shape

Shape
180 mm
180 mm

Pick your printer below the preview to check the shade fits its bed.

120 mm

A globe’s openings: the ball grows with the height, and turns into 45° cones near each opening so it prints.

6
120 °
28
5.0 mm

Wall

Wall
0.60 mm

Set the same line width in your slicer. The fitter’s collar is made to slide just inside a wall this thick.

1.6 mm

1.6 mm is four lines on a 0.4 mm nozzle.

Pattern
12
3.5 mm
7

Each number gives a different layout of cells.

24
9.0 mm
Hole shape
16
5.0 mm
60 mm
6.0 mm
60 °

Measured from horizontal. 45° or steeper prints without supports.

15 %
85 %
0.8 mm
3.0 mm
0

Automatic keeps the picture’s proportions.

Fitting

LED bulbs only. Printed plastic softens in heat: never use an incandescent or halogen bulb, and keep the bulb clear of the wall.

Fitter
Socket
40.0 mm

Typical holes: E27 40 mm, E14 27 mm, E26 about 35 mm. Sockets vary, so measure the threaded collar under the shade ring and add 0.5 mm.

Ring sits

At the top: the bulb hangs inside, as on a pendant or a downward socket. At the bottom: the shade stands on an upward socket.

7.0 mm

Measure the threaded stud on top of your harp and add 0.5 mm. The finial screws down onto the washer.

40 mm

The tabs rest on the bulb’s dome where it is this wide. A smaller ring sits higher on the bulb.

Spokes
8.0 mm
3.0 mm

Socket shade rings take up to about 6 mm of material.

A cover that slides up the cord over your ceiling cup.

100 mm
25 mm
7.0 mm
60 mm

Measure across the widest part. A common household bulb is about 60 mm.

60 mm

Measure along the lamp from the fitter’s seat to the middle of the bulb. With no fitter, from the top of the shade.

Base and finish

A simple base with a collar for your socket and a notch for the cord. Use a certified lamp kit.

130 mm
70 mm
160 mm
40.0 mm

Measure across the socket’s body. The collar is 0.5 mm wider.

10.5 mm

The hole for the threaded tube or cord entry under your socket.

7.0 mm
Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    Safety first

    LED bulbs only

    • LED bulbs only. Incandescent and halogen bulbs turn about 90% of their power into heat. Never use one in a printed shade.
    • Keep the bulb clear of the wall. The studio shows the gap from your measured bulb to the nearest wall. We suggest at least 25 mm; that is our rule of thumb, not a standard.
    • Pick the plastic for the heat. PLA softens at about 60 °C. PETG is good to about 80 °C and ASA to about 93 °C. A clip-on shade touches the bulb, so print it in PETG or ASA.
    • Use certified electrical parts. Build the lamp from a certified lamp kit and follow its instructions. This page gives no wiring advice and makes no electrical safety claims.
    • Never leave a new lamp on unattended until you have checked that the shade stays cool.

    The method

    How to make a lamp shade that fits

    1. Pick a shape and set the height and diameters.
    2. Choose the wall: vase mode for a light, seamless shade, or a patterned wall that lets light through.
    3. Measure your hardware: the socket’s threaded collar, the harp’s stud or your bulb, and enter it. The fitter’s hole is made to that size.
    4. Check the bulb clearance under the preview, then download and print with the fitter end on the bed.

    Fitters

    Which fitter does my lamp use?

    FitterFitsWhat to measure
    Socket ring (uno)Lamps where the socket has a threaded collar and a shade ringThe collar’s outside diameter. Typical holes: E27 40 mm, E14 27 mm, E26 about 35 mm.
    Harp spiderTable lamps with a harp (a wire hoop over the bulb) and a finial on topThe stud on top of the harp
    Bulb clipSmall shades that rest on the bulbThe bulb’s width, and how wide it is where the clip should sit
    PendantHanging lamps; the ring clamps under the socket’s shade ringThe socket’s collar, and your ceiling cup for the cover
    NoneAn open shade to fit your own frameNothing

    The fitter lies flat at one end of the shade, so it prints on the bed with no supports. Its spokes run into the wall. On a narrow end with no room for spokes, the fitter becomes one solid ring.

    Walls

    Vase mode or patterned wall

    WallHow it printsGood for
    Vase modeOne continuous line, no seam. The fitter is a separate part glued into the end.Twisted, faceted and pleated shades with a soft glow
    Voronoi, perforated, waves, spiralA solid wall with openings. Every opening is closed in by the rims.Patterns of light on the walls
    Lithophane bandThe wall gets thicker where the picture is dark. Print with 100% infill.A photo that appears when the lamp is on

    Printing

    Printing tips

    • Fitter end down: the shade is laid out that way, so the spokes print flat.
    • Vase mode: turn on spiral vase mode and set bottom layers to 0, so both ends stay open.
    • Overhangs: keep the wall within about 45° of vertical. The studio warns you when a shape leans further.
    • Bridges: the top of each opening is a short bridge; slow bridges down if they sag.
    • Translucent filament in white or a warm tone glows evenly.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. If the shade is too wide or tall for the bed, make it smaller.

    Can I sell shades I print?

    The designs you make are yours. We make no claims about electrical safety or approval, so if you sell lamps or shades, check the rules for lighting products where you sell them.

    Can I use a normal (incandescent) bulb?

    No. Use LED bulbs only. Incandescent and halogen bulbs run far too hot for a printed shade.

    Is the ring hole a standard size?

    The typical values come from lamp part sellers. The official thread sizes are in a paid standard, and real sockets vary, so always measure yours.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. PLA Prusa Research
    2. PETG Prusa Research
    3. ASA Prusa Research
    4. LED lighting U.S. Department of Energy
    5. Lamp holders that could hold a shade Creative Cables
    6. Uno threaded keyless socket with shade ring Grand Brass Lamp Parts
    7. A-series light bulb Wikipedia
    8. Standard sheets for barrel thread for E14 and E27 lampholders with shade holder ring (IEC 60399) IEC
    9. Layers and perimeters (spiral vase) Prusa Research