Free generator · Runs in your browser

Wall plate generator Cover it your way.

Make a switch, outlet or media cover plate for 1 to 5 gangs: toggle, rocker, outlet, blank, coax, keystone or a round hole in each gang, in standard, midway or jumbo size, with a label or pattern. A cover plate only: turn the power off before fitting it.

  • Private by designNothing leaves this device
  • Seven openingsMix them gang by gang
  • No supportsPrints face down
  • Ready to sliceSTL or two-colour 3MF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Plate

A cover plate only. It never replaces a rated switch, outlet, box or cover. Turn the power off at the breaker before you take a plate off or fit one, and use PETG or ASA near heat.

Plate size

Standard plates fit most boxes. Midway and jumbo plates are bigger, to cover a ragged wall cut-out. Measured: type the size of the plate you are replacing.

Measure the old plate edge to edge. It is made bigger if it would not cover the openings and screws.

Gangs (devices side by side)

Openings

2

Stacked one above the other. The plate is thinned to 1.6 mm round each cutout so the jack clips in.

1

Holes for barrel-style F connectors that fasten with a nut.

25.0 mm

For a cable pass-through, a grommet or a speaker terminal. Measure the part it is for.

0.20 mm

Added to every opening’s width and height. Printed holes come out a little small; 0.2 mm makes up for most printers.

Shaped for the oval-head screws that come with plates, so the heads sit low.

Shape

2.5 mm

Bought plastic plates are about 1.8 mm. Printed plates are better a little thicker.

5.6 mm

How far the plate stands off the wall. Standard plates are about 5.6 mm, midway and jumbo 6.5 mm. Make it deeper if the device sits proud of the wall.

1.6 mm
Edge
2.0 mm

How far the front face is set in from the edge. Capped so the edge never overhangs more than 45° as it prints.

3.0 mm

Label and pattern

Above or below fits toggle and outlet plates best. A blank gang gives a large label area.

Short words read best: a room, a circuit, or what a switch runs. A second line works on blank gangs.

8.0 mm

Shrunk to fit the space if it is too big.

Typeface

Engraved into the front, kept clear of the openings, screws, label and edge.

4.0 mm

The spacing of the pattern. On big plates a fine pattern is spread out a little so it stays quick to build.

Label and pattern

Inlaid fills the engraving flush with a second colour: it needs a printer that changes filament within a layer.

0.6 mm

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    Safety first

    A cover plate, nothing more

    • Turn the power off at the breaker or fuse before you take a plate off or fit one, and check it is off.
    • A cover plate only. It covers a switch or outlet that is already installed in a box. It never replaces a rated switch, outlet, box, cover or any other electrical part, and it is not a weatherproof or outdoor cover.
    • Not tested or listed. A printed plate is not tested to any electrical standard, so we make no claim that it meets a building or electrical code. If in doubt, ask an electrician.
    • Heat: PLA softens at about 55–60 °C. Near a dimmer, a heater, a stove or in a hot sunny spot, print in PETG or ASA.
    • Low-voltage cables only through keystone, coax and round holes: network, TV, speaker or alarm wiring, never mains wiring.
    • No night-lights, lights or anything powered: this generator makes plain plastic covers only.

    The method

    How to make a wall plate

    Choose a plate size and how many gangs (devices side by side) it covers, then set each gang’s opening. The generator places the openings and screw holes at the standard spacings for North American (US and Canadian) boxes, and adds a rim round the back so the plate sits against the wall.

    1. Check what you are covering: count the devices and note each one’s type.
    2. Pick the plate size. To match an old plate exactly, measure it and choose Measured.
    3. Set each gang: toggle, rocker, outlet, blank, coax, keystone or a round hole.
    4. Add a label or a pattern if you like, then download and print it face down.
    5. Fit it with the power off, using the screws from the old plate.

    Sizes

    Plate sizes

    Size1-gang widthHeight2 · 5 gangs wideDepth
    Standard69.8 mm (2.75″)114.3 mm (4.50″)115.8 mm · 253.8 mm5.6 mm
    Midway (mid-size)79.4 mm (3.13″)123.8 mm (4.87″)125.4 mm · 263.4 mm6.5 mm
    Jumbo (oversize)88.9 mm (3.50″)133.4 mm (5.25″)134.9 mm · 272.9 mm6.5 mm

    Each extra gang adds 46.0 mm (1.81″), the spacing of devices in a multi-gang box. Plates from other countries use other sizes and screw positions; this generator does not make them.

    Openings

    Openings and screws

    GangOpeningScrews
    Toggle switch10.2 mm × 23.6 mm2, 60.3 mm apart
    Rocker / decorator33.3 mm × 67.1 mm2, 96.7 mm apart
    Duplex outletTwo 34.1 mm rounds with flats 28.6 mm apart, centres 38.7 mm apart1, in the middle
    BlankNone2, 83.3 mm apart (box)
    Coax9.8 mm round, for a 3/8″ F barrel2, box or strap spacing
    Keystone jack14.8 mm × 19.3 mm, panel thinned to 1.6 mm2, 83.3 mm apart
    Round holeYour size, 6–38 mm2, box or strap spacing

    Screw holes are 3.7 mm through, countersunk at 82° to 7.4 mm across for #6-32 oval-head plate screws. The extra opening size is added to every opening, as printed holes shrink a little.

    Printing

    Printing tips

    • Face down, no supports. The front prints on the bed, so it comes out smooth; a textured sheet gives it a texture. The edge never overhangs more than 45°.
    • Material: PLA is fine away from heat; PETG or ASA near dimmers, heaters or in the sun.
    • Strength: 3–4 walls and 20% infill or more. Don’t over-tighten the screws: snug is enough.
    • Two colours: an inlaid label needs a printer that changes filament within a layer. On one nozzle, print the plate engraved and fill the letters with paint or wax.
    • Keystone jacks clip into a 1.6 mm panel. Print one keystone gang first to check your jacks snap in, and adjust the extra opening size if they are tight.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. One- to three-gang plates fit most printers; four and five gangs need a bed over 210 mm or 255 mm wide.

    Will it fit my box?

    It follows the common North American sizes and screw spacings from manufacturers’ size guides, which fit most boxes and devices. Hold a print against your devices before you rely on it, and measure an old plate if you need a match.

    Is a printed plate safe?

    It is a plain cover over devices that are already installed, like a bought plastic plate, but it is not tested or listed to any electrical standard. Turn the power off before fitting it, never use it in place of a rated part, and use PETG or ASA near heat.

    Can I sell plates I print?

    The designs you make are yours, and plain wall plates are common hardware anyone may make. The typefaces are open-licensed, which allows making physical products. We make no claim beyond that: a plate for sale may need to meet the electrical product rules where you sell it.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Wallplate size guide (Q-1289) Leviton
    2. Wallplate dimensional information Arrow Hart (Eaton)
    3. Wall plates and specialties catalog Pass & Seymour (Legrand)
    4. Electrical faceplate types and dimensions Archtoolbox
    5. #6-32 slotted oval machine screw dimensions Aspen Fasteners
    6. Keystone module widths and mountings Delock
    7. Keystone module Wikipedia
    8. F connector Wikipedia
    9. Multi-material printing Prusa Research
    10. SIL Open Font License SIL International