Free generator · Runs in your browser

Dice generator Roll your own.

Make a full set of polyhedral dice, or any single die, with numbers engraved for paint or inlaid in a second colour. Add a custom face, pick your typeface, and print with no supports.

  • Private by designNothing leaves this device
  • Seven diced4 to d20, plus d%
  • No supportsEach die prints on a face
  • Ready to sliceEvery die its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Dice

Make
Die
16 mm

Sets are sold by the d6’s edge: standard sets are 16 mm. The other dice are sized to match.

100 %
1

Several sets, or a handful of d6s, packed onto your plates.

Corners

Numbers

Numbers
0.8 mm
0.85 ×

1 fills each face as far as its edges allow.

d6 faces
6 and 9
Typeface

Custom face

Initials, a short word or a symbol such as ★ ♥ ☠, on the 20 of a d20, the 6 of a d6 and so on.

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How the dice are made

    Each die is the solid left between its face planes, with its corners trimmed a little. The numbers are cut straight into the faces, the same depth everywhere, and opposite faces add up to one more than the number of sides (on a d10, to 9), as on standard dice.

    1. Pick a full set or one die, and your set size.
    2. Choose the numbers: engraved to paint, or a two-colour inlay.
    3. Add a custom face if you like.
    4. Download and print, lowest number down.

    The set

    What’s in a set

    DieShapeSize in a 16 mm set
    d4Tetrahedron: three numbers per face, read at the top corner18.4 mm
    d6Cube: numbers or pips16 mm
    d8Octahedron15.2 mm
    d10Pentagonal trapezohedron, 0–916 mm
    d%Same shape, 00–90 for percentile rolls16 mm
    d12Dodecahedron17.6 mm
    d20Icosahedron18 mm

    Finishing

    Inking the numbers

    • Paint: work acrylic paint into the numbers, wait a minute, then wipe the face with a damp cloth or a card edge.
    • Crayon: rub wax crayon over the face and buff it off: the wax stays in the numbers.
    • Two colours: on a multi-material printer, the inlay prints the numbers in their own filament, flush with the faces.

    Rolling fair

    Will printed dice roll fair?

    Opposite faces add up correctly, and every face has the same depth of engraving. But printed dice are never as even as machined ones: infill, seams and sagging overhangs can all favour some faces. Print with 100% infill (or many walls) and fine layers, and use them for play, not for tournaments.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Do I need supports?

    No. Each die prints on a face. The d20’s lower faces lean a little past 45°, which small dice print fine.

    Can I put my own symbol on a die?

    Yes: switch on the custom face and type up to four characters or a symbol. It replaces the highest number.

    Can I sell dice I print?

    The designs you make are yours, and the typefaces are open-licensed, which allows making physical products. Dice are small parts, so check toy-safety rules before selling for children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-09. Community posts are one maker's experience, not a specification.

    1. Dice sizes: what size is standard? Bryce’s Dice
    2. Measurements of standard polyhedral dice (forum discussion) The Straight Dope Message Board
    3. SIL Open Font License SIL International