Free generator · Runs in your browser

Plant pot generator Grow something.

Design a plant pot with drainage and a drip saucer, a self-watering pot with a reservoir and wick, a hanging or wall planter, or a plate of mini succulent pots.

  • Free and privateNothing leaves this device
  • Nine shapesPlus textures and faces
  • No supportsPrints upright
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Planter

Type
6
60 mm

Height and base follow. Holes are at most 6 mm.

Each pot takes the next shape in turn.

110 mm
120 mm

Outside, across the flats for square and hexagon pots. Pick your printer below the preview to check it fits.

95 mm

Ignored by the cylinder.

Shape

Shape
6
0.12
7

Try another number for a different random gem.

Faceted pots are plain: textures don’t apply.

24
2.0 mm
90 °
Face
1.6 mm

The cat has ears on the rim (not on self-watering pots, where the inner pot’s flange sits).

Walls and surface

0.40 mm

The wall is a whole number of lines this wide. Most printers ship with a 0.4 mm nozzle.

4
2.4 mm

A solid model for the slicer’s vase mode: one wall, no drainage holes. Use it as a cover pot.

Surface texture
18
1.2 mm

Added outside the wall, so the wall keeps its thickness.

Water

Drainage
8.0 mm
3.0 mm

Gap all round between the pot and the saucer wall.

3.0 mm

The pot stands on these, clear of drained water. 0 for no feet.

15 mm
40 mm

From the floor to where the soil starts. Deeper holds more water.

10.0 mm

For a cotton cord wick. Measure your cord; 0 for none.

14 mm
5.0 mm

Measure your cord; the holes are 0.8 mm bigger.

8.0 mm

Measure your screws: the round part of the keyhole is 0.6 mm wider than the head.

4.0 mm

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a plant pot

    Choose the kind of planter and its size, pick a shape and a surface, then decide how it handles water. The generator builds a closed, printable pot with its floor, holes, saucer or inner pot, and tells you how much soil it holds.

    1. Pick the type: a pot, a self-watering pot, a hanging pot, a wall half-pot or a plate of mini pots.
    2. Set the size: height, rim and base. The readout shows the soil volume in litres.
    3. Shape and surface: nine shapes, a texture, or a face.
    4. Water: drainage holes and a saucer, or a reservoir and wick.
    5. Download and print upright, with no supports.

    Options

    Planter types

    TypeWhat you getGood for
    PotA pot with drainage holes and, if you like, a drip saucer on feetMost houseplants
    Self-wateringA reservoir pot and an inner pot with a wicking cup and a fill channelHerbs and thirsty plants; going away
    HangingThree lugs on the rim for cordTrailing plants
    Wall half-potA flat back and a plate with keyhole slotsSmall plants on a wall
    Mini potsUp to 16 small pots on the bed, in one shape or a mixSucculents, cuttings, gifts
    Spiral vase modeA solid model your slicer prints as one wallCover pots over a nursery pot

    Walls

    Wall thickness in whole lines

    The wall is a whole number of lines of your nozzle width: four lines of 0.4 mm make a 1.6 mm wall. Set the same line width for perimeters in your slicer and at least that many perimeters, so the wall prints as solid lines with no thin gap filled by zig-zags. Textures and faces are added outside the wall, so they never make it thinner.

    Printing

    Printing tips

    • No supports: pots print upright. Keep the side within about 45° of vertical; the advice warns you if it isn’t.
    • Watertight: printed walls can weep. For a saucer or reservoir use more perimeters, solid top and bottom layers, or seal the inside.
    • Outdoors: PETG or ASA stand up to sun and heat better than PLA.
    • Drainage: keep holes clear; saucer feet hold the pot out of drained water.
    • Vase mode: one wall, no holes; use it as a cover pot.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. If the pot is too big, lower the height or diameters. A saucer, an inner pot and mini pots are laid out beside the pot, and spread over more plates when needed.

    How does the self-watering pot work?

    Water sits in the outer pot. The inner pot hangs from the rim, and its cup at the bottom reaches into the water: soil packed in the cup, or a cotton cord through the hole, draws water up into the pot. Top up through the channel at the side.

    Can I sell pots I print?

    The designs you make are yours, and plant pots are a traditional shape anyone may make. There are no claims beyond that.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Growing plants in containers Royal Horticultural Society
    2. So, why do plant containers have drain holes? Mississippi State University Extension
    3. Make a self-watering container Garden Organic
    4. Layers and perimeters (spiral vase) Prusa Research
    5. PETG Prusa Research