Free generator · Runs in your browser

Flexi animal generator Wiggles off the bed.

Make a print-in-place flexi dragon, snake, fish, caterpillar or axolotl: real pin joints with a clearance you set, a name along its back, two colours, and a coil that fits your printer’s bed. No model to upload.

  • Private by designNothing leaves this device
  • Five animalsMade from your settings
  • No supportsJoints print already linked
  • Ready to sliceColours as separate objects

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Animal

Animal
240 mm

Measured along the body. Longer than your bed? It coils up to fit.

14

Including the head and tail. More segments bend more smoothly; each needs about 10 mm of length.

26 mm
60 %

0% keeps the body the same width to the tail; higher values make a slimmer tail.

7.0 mm

Thicker bodies have stronger joints. Spikes, eyes and letters stand on top.

Joints

0.35 mm

The gap around every pin. 0.3–0.4 mm suits most printers with a 0.4 mm nozzle. Too tight and the joints fuse; too loose and they wobble. Print a tolerance test to find yours.

Layout on the bed

“Fit my bed” lays it in a gentle S-curve, turned to fit, and coils it if it is still too long. Pick your printer below the preview to use its bed.

Turn off for a plain, smooth animal.

Name and extras

One letter per body segment. Leave empty for none.

Letters
Typeface
1.0 mm

A 5 mm hole for a key ring. Replaces the snake’s tongue.

Colours

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a flexi animal

    A flexi animal is a chain of flat segments joined by joints that print already linked. Each segment carries a pin at its front that sits inside a ring at the back of the segment ahead, with a small gap all round. Nothing is glued or assembled: it comes off the bed in one piece and wiggles.

    1. Pick an animal and set its length, segments, width and thickness.
    2. Set the joint clearance for your printer, and pick your printer below the preview so a long animal coils to fit.
    3. Add a name and choose one colour, body and details, or striped segments.
    4. Download, print flat with no supports, then gently work each joint loose.

    Joints

    How the joints work

    Each pin is a short barrel with 45° chamfers top and bottom. The ring around it follows the same shape one clearance away, so its lips sit over and under the pin and hold it in. The ring is open towards the tail through a slot narrower than the pin, which lets the neck through but not the pin. The neck stops one clearance short of both lips, and its underside is a short bridge of about 3 mm.

    The front of each segment is a curve around the joint, so the gap stays the same as it turns. Each joint bends about 20–25° each way (the dragon’s wing joints about 11°, so the wings have room), so a 14-segment animal can curl most of the way round.

    SettingTypicalWhat it changes
    Clearance0.3–0.4 mmGap around every pin and between segments
    Thickness6–8 mmTaller pins and necks are stronger
    Segments10–20More segments bend more smoothly
    Body width20–30 mmWider bodies get bigger, stronger pins

    Animals

    The animals

    AnimalHeadBodyTail
    DragonRaised skull, brows, eyes, swept horns and cheek frillsBack spikes that grow to the middle, two pairs of bat wings with raised bonesSpade tip
    SnakeRaised crown, brows, eyes and forked tongueDiamond pattern on the backLong point
    FishBig eyes, gill line and lipSide fins and a back finForked tail fin
    CaterpillarDomed head, eyes, smile and antennaeSpots and little feetRound end
    AxolotlWide, with a smile and gillsLegs and spotsLong pointed tail

    Printing

    Printing tips

    • No supports, no brim near the joints. Overhangs are 45° or bridged; supports would lock the joints.
    • Watch the first layer. A squashed first layer (elephant’s foot) can fuse a pin to its ring. Turn on elephant foot compensation if your slicer has it.
    • PLA or PETG. PETG is stickier, so add about 0.05–0.1 mm of clearance.
    • After printing, hold two neighbouring segments and bend them gently a little each way, working down the body. Don’t twist hard.
    • Two colours on one nozzle: eyes, spikes and letters stand on top, so a colour change at the body’s thickness colours them.
    • Small parts: not for children under 3.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits. You do not need to upload a model: the whole animal is made from the settings.

    Will it fit my printer?

    Choose your printer below the preview. If the animal is longer than the bed, “Fit my bed” lays it across the diagonal or coils it, with every joint inside its range, so it still prints in one go.

    Will the joints work first time?

    They should with the right clearance, but every printer is a little different. If joints fuse, raise the clearance by 0.05 mm or fix the first layer; if they wobble, lower it. A quick tolerance test print tells you your number.

    Can I sell animals I print?

    The designs you make are yours, and the shapes here are original. The typefaces are open-licensed, which allows making physical products. These are toys with small parts, so check toy-safety rules before selling them for children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-11. Community posts are one maker's experience, not a specification.

    1. Print-in-place 3D printing: hinges, joints and moving parts Sovol
    2. Modeling with 3D printing in mind Prusa Research
    3. Elephant foot compensation Prusa Research
    4. Small parts ban and choking hazard labeling U.S. Consumer Product Safety Commission
    5. SIL Open Font License SIL International