Free generator · Runs in your browser

Timing pulley generator Teeth that fit your belt.

Make timing pulleys, idlers and ratio pairs for 2GT / GT2-compatible, 3GT-compatible, HTD-compatible 3M and 5M, T2.5, T5 and MXL belts: any tooth count, flanges, a set-screw hub with nut traps, motor and bearing bores, and the belt length worked out.

  • Private by designNothing leaves this device
  • Seven belt profilesPitch and pitch line from catalogues
  • No supportsShaped to print flange-down
  • Ready to sliceSTL and 3MF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Belt and teeth

Make

Match the belt you have: the profile and pitch are printed on most belts. These are profile families, not branded parts.

Belt width
Belt width
Belt width
Belt width
Belt width
Belt width
Belt width
Idler surface
20.0 mm

A smooth idler usually runs on the back of the belt. It must be wider than the bearing inside it.

20

For a pair, this is the driver (the motor’s pulley).

3.00 : 1

The driven pulley gets the nearest whole number of teeth; the readout shows the exact ratio.

Work out
100 mm

Shaft to shaft. The generator picks the nearest whole-tooth belt and shows the exact distance for it.

Closed belts are sold by tooth count or length: length ÷ pitch = teeth.

300 rpm

Fit and flanges

0.00 mm

Above 0 widens every groove for a looser belt; below 0 narrows it. Print the fit test to choose.

Prints just the teeth at 0.1 mm tighter, as set and 0.1 mm looser, marked with 1, 2 and 3 dots.

Flanges
Top flange
1.5 mm
1.2 mm
0 °

Slopes the belt side of the bottom flange (and a separate ring) outward to guide the belt in. A one-piece top flange always has 45°.

Bore and hub

6.0 mm
6.35 mm

Measure across two flat sides of your shaft.

10.0 mm
6.35 mm
0.15 mm

Added to the shaft size. Printed holes come out slightly small.

16.0 mm

Grows by itself if it is too small for the nut.

8.0 mm
Set screws
Screw size

A slot for a hex nut behind each set screw, so the screw bites into metal, not plastic.

Bearings
0.10 mm

Added to the bearing’s outside diameter. Lower for a tighter press fit.

5.3 mm

Colour

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a timing pulley

    Choose the belt you have, the number of teeth and the shaft it goes on. The generator sizes the teeth from the belt’s pitch and pitch line, adds flanges, a hub with set screws and nut traps, or bearing seats for an idler, and stands it up the way it prints best.

    1. Pick the belt profile and width. The pitch is usually printed on the belt.
    2. Set the teeth. For a pair, set the driver’s teeth and the ratio.
    3. Choose the bore, or bearings for an idler.
    4. Print the fit test, adjust Tooth fit, then print the pulley.

    Belts

    Belt profiles

    ProfilePitchBelt tooth heightPD − OD (2 × pitch line)GrooveBelt widths
    2GT / GT2-compatible, 2 mm2 mm0.75 mm0.508 mmCurved (approximation)6, 9, 10 mm
    3GT-compatible, 3 mm3 mm1.14 mm0.762 mmCurved (approximation)6, 9, 15 mm
    HTD-compatible 3M, 3 mm3 mm1.2 mm0.762 mmCurved (approximation)6, 9, 15 mm
    HTD-compatible 5M, 5 mm5 mm2.1 mm1.143 mmCurved (approximation)9, 15, 25 mm
    T2.5 trapezoidal, 2.5 mm2.5 mm0.7 mm0.526 mmTrapezoid4, 6, 10 mm
    T5 trapezoidal, 5 mm5 mm1.2 mm0.82 mmTrapezoid10, 15, 25 mm
    MXL trapezoidal, 2.032 mm2.032 mm0.51 mm0.508 mmTrapezoid (standard rack)4.8, 6.4, 9.5 mm

    About the names: GT2 and HTD are trade names of a belt maker. Here they only name a profile family: these pulleys are drawn from published dimensions to fit belts of that shape, and they are not that maker’s parts. 2GT, 3GT, 3M and 5M have curved teeth; T2.5, T5 and MXL have straight-sided, trapezoid teeth. A T5 belt does not fit a 5M pulley, even though both have a 5 mm pitch.

    How the grooves are drawn: curved-tooth groove shapes are not openly published, so the generator uses a documented approximation: a round floor at the published groove depth, flanks that open slightly, and rounded tips. The T5 groove follows a published pulley drawing, MXL follows the standard’s cutting-rack shape, and T2.5 scales the T5 groove to the smaller belt. That is why there is a fit test.

    Sizes

    Pitch diameter, outside diameter and belt length

    A belt’s pitch line runs through its cords, a little outside the pulley’s teeth. So a pulley has two diameters:

    • Pitch diameter = teeth × pitch ÷ π. A 20-tooth 2GT pulley: 20 × 2 ÷ π = 12.73 mm.
    • Outside diameter = pitch diameter − 2 × pitch line offset. For 2GT the offset is 0.254 mm, so 12.22 mm, the same as catalogue pulleys.
    • Belt length for two pulleys, on the pitch line: L = 2C·sin(θ/2) + R(2π − θ) + rθ, where C is the centre distance, R and r the pitch radii, and θ = 2·acos((R − r) ÷ C) the wrap on the small pulley. Belts come in whole teeth, so the generator rounds to the nearest belt and works the centre distance back out.
    • Teeth in mesh on the small pulley = its teeth × θ ÷ 2π. Belt makers rate drives for at least six.

    Hardware

    Shafts, bearings and screws

    PartSizeUsed for
    5 mm motor shaft with flatØ5 mm, 4.5 mm across the flatCommon stepper motors; the set screw lands on the flat
    608 bearing8 × 22 × 7 mmLarge idlers
    625 bearing5 × 16 × 5 mmIdlers on a 5 mm shaft or M5 bolt
    623 bearing3 × 10 × 4 mmSmall idlers on M3
    M3 hex nut5.5 mm across flats, 2.4 mm thickSet-screw nut traps
    M4 hex nut7 mm across flats, 3.2 mm thickSet-screw nut traps on larger hubs

    Check your own parts with calipers: motor shafts and bearings from different makers can differ slightly.

    Printing

    Printing tips

    • Orientation: bottom flange on the bed, hub on top. Everything is shaped to print without supports: the one-piece top flange has a 45° underside, nut slots open at the top, set-screw holes have a pointed top, and a wide hub rises on a 45° collar.
    • Two flanges, two ways: the one-piece flange is quickest. A separate ring has a flat belt side; print it beside the pulley and glue it on. It needs a hub narrower than the teeth, or no hub, so it can sit on top of the teeth.
    • Fit test first: turn on Quick fit test, print the three slices and press your belt in. Pick the one that seats flat without rocking.
    • Layers: 0.1–0.15 mm layers and a 0.4 mm nozzle give the cleanest small teeth. Slow outer walls help.
    • Material: PETG, ABS or ASA for pulleys on warm motors; PLA is fine for light, cool jobs.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Very large pulleys (150 teeth on a 5 mm pitch is about 24 cm across) may need a bigger bed or fewer teeth.

    Is this the same as a branded GT2 or HTD pulley?

    No. It is drawn to fit belts of that profile family, from published pitch and pitch-line figures. The tooth shape of curved profiles is a close approximation, so print the fit test and tune Tooth fit for your belt and printer.

    Can I sell pulleys I print?

    The designs you make are yours. Profile names are used only to describe which belts they fit; don’t sell them as a belt maker’s own parts. Pulleys come with no rating for load or speed, so test them in your machine.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. High torque timing pulleys 1.5GT and 2GT (PD, OD, pitch line and tooth depth) Misumi
    2. High torque timing pulleys 3GT Misumi
    3. Timing pulleys T5 (standard tooth profile) Misumi
    4. Timing pulleys T2.5 Misumi
    5. Timing pulleys MXL Misumi
    6. Timing belts and pulleys overview (ISO 5294 cutting rack, tooth heights) Misumi
    7. Timing belt pulleys, 3M and 5M pitch (PD and OD tables) Optibelt, via RS Components
    8. Timing belt pitch chart (tooth heights) Texas Belting
    9. Belt problem: length of an open belt Wikipedia
    10. Minimum belt wrap and tooth engagement Gates
    11. Ball bearing dimension table (608, 625, 623) igus
    12. ST 17 stepper motor datasheet (5 mm shaft, D-cut 4.5 mm) MAE
    13. DIN EN ISO 4032 hexagon nuts fasten.it
    14. ISO 17396: T and AT profile belts and pulleys (catalogue entry) iTeh Standards