Free generator · Runs in your browser

Hexagon shelf generator Plan the wall, cell by cell.

Design honeycomb wall shelves in hexagons, triangles, diamonds, octagons or circles: arrange the cells, add a ledge, planter, mirror, LED strip or photo slot, and get the connectors, keyholes and a full-size template for the screws.

  • Private by designNothing leaves this device
  • Five cell shapesArranged on a grid you plan
  • No supportsCells print on their backs
  • A 1:1 wall templateEvery screw marked

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Shape

Cell shape
150 mm

Inside the walls: across the flats for hexagons, octagons and diamonds, the height for triangles, the diameter for circles.

80 mm
5.0 mm

Thicker walls are stiffer and give clips and dowels more grip.

Back
3.0 mm

Arrangement

Click a place to add or remove a cell. With an inside brush (ledge, planter, mirror, LED strip, photo slot), click a cell to give it that inside, or click again to clear it. The keyhole brush marks the cells that hang on the wall. With the keyboard: arrow keys move, Space applies the brush, 1 to 8 pick a brush, Delete removes a cell, Ctrl+Z undoes. Neighbouring cells are joined on every edge they share.

Wall plan

Wall plan: 5 cells, 462 by 400 mm, 2 screws marked in red462 mm400 mm12345

The template prints at actual size on A4 sheets that overlap by 15 mm. Check its 100 mm scale bar with a ruler before you drill.

Joins and mounting

Join touching cells with

Printed butterfly clips press into dovetail pockets in the back of both walls.

Printed flat plates glue into shallow pockets in the back of both walls.

Measure your dowel or metal pin. The holes are 0.3 mm wider, and the advice gives the length to cut.

Countersunk wood screw sizes from DIN 7997. For other screws, choose Measured.

Inside the cells

These sizes apply to every cell you give that inside on the arrangement grid.

50 %

How far up the opening the ledge sits.

Measure your pot. The tray is sized to it with 2 mm to spare, and the advice says if it fits.

15 mm

The advice gives the mirror size the front rebate takes.

Measure your stick-on strip.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make honeycomb wall shelves

    Pick a cell shape and size, place the cells on the arrangement grid, and the generator joins every pair of touching edges, adds keyholes to the cells you mark, and draws a full-size template for the screws.

    1. Pick the shape, its inner size, depth and wall.
    2. Arrange the cells: click or use the keyboard, and give cells a ledge, planter, mirror, LED strip or photo slot.
    3. Choose the joins and the keyhole screw.
    4. Download the cells and the wall template, tape the template up level and mark the screws.

    Options

    Shapes and insides

    OptionWhat it isGood to know
    HexagonThe classic honeycomb, flat top and bottomSize is across the flats; each cell meets up to six others
    TriangleAlternating up and down trianglesSize is the height; up triangles have a flat floor
    DiamondSquares on their cornersSize is across the flats; no flat floor
    OctagonOctagons side by side and stackedSize is across the flats; meets up to four others
    CircleRound cells in a honeycomb patternSize is the diameter; small flats where they touch
    Shelf ledgeA shelf across the openingSet its height as a share of the opening
    PlanterA drip tray for a measured potThe pot stays in its own pot with holes
    MirrorA rebate in the front for a mirrorThe advice gives the mirror size
    LED stripA groove inside the front edge, with a cable hole and channel in the back panelFor low-voltage stick-on strips
    Photo slotA slot in the floor that holds a photo or card uprightNeeds a flat floor

    Joining

    Clips, plates and dowels

    Cells sit 0.2 mm apart, and every pair of edges that touch gets a joint: one in the middle, or two on long edges. Clips and plates are printed with the set. At the default 5 mm wall, each clip pocket runs 3.8 mm into the wall.

    JoinHow it worksBest for
    Butterfly clipsDovetail pockets in the back of both walls; the clip presses in from behindMost shelves; take apart again if not glued
    Flat platesShallow pockets; the plate is glued inThin walls
    Hidden dowelsBlind holes through the touching walls for a dowel or pin you measureA clean look; glue for strength

    Printing

    Printing and hanging tips

    • Orientation: every cell prints on its back with the open front up, with no supports.
    • Big cells: a cell larger than your bed prints in two halves that slide together on dovetails. Glue them.
    • Keyholes: the slot sits against the wall with room for the screw head behind it. Leave each head about 2.5 mm proud, hang the cell and slide it down.
    • Wall anchors: use the screw and anchor that suit your wall (plasterboard, masonry or timber).
    • Loads: there is no load rating. Plastic creeps under a steady load, especially when warm, so keep heavy things off and check the shelves now and then.
    • Planters: keep plants in pots with drainage holes and empty the tray, so water never reaches the wall.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Cells that are too big split in two along a dovetailed cut, and every part spreads over as many plates as needed.

    Can I sell shelves I print?

    The designs you make are yours. Honeycomb shelves are a common shape that anyone may make. The generator makes no claims about strength or safety, so test what you sell and say what it is for.

    How much weight will it hold?

    The generator gives no load rating. It depends on the material, the print settings, the wall and the anchors. Use the shelves for light decor.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. DIN 7997: cross-recessed countersunk head wood screws, dimensions fasten.it
    2. Drywall and hollow-wall anchor buying guide Lowe’s
    3. Modeling with 3D printing in mind (orientation and strength) Prusa Research
    4. PETG Prusa Research
    5. Growing plants in containers Royal Horticultural Society
    6. So, why do plant containers have drain holes? Mississippi State University Extension
    7. LED strip light Wikipedia