Free generator · Runs in your browser

Lathe generator Draw it, spin it.

Draw half an outline and turn it into anything round: vases, bowls, cups, candlesticks, game pieces, finials, knobs and spinning tops. Or trace one from a photo.

  • Private by designPhotos stay on this device
  • Any round shape16 shapes to start from
  • Print-awareOverhangs shown as you draw
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Profile

Drag a point to move it. Double-click an empty spot to add a point, or a point to delete it. With the keyboard: [ and ] pick the previous or next point, arrow keys move it (Shift for 10 steps), S makes it smooth or sharp, Insert adds a point, Delete removes it, Ctrl+Z undoes. The point table below does the same with typed numbers. Red parts of the line overhang more than 45°.

    Type a new height or diameter to stretch the whole profile that way.

    Loading a shape replaces the profile (Undo brings it back) and picks the settings it suits.

    Point table (mm)

    Radius is the distance from the axis; height is from the bottom. Points run from the bottom up.

    Profile points
    #RadiusHeightSmoothActions
    Trace from a photo

    Take the photo from the side and from a few steps back (zoom in), against a plain background. The right-hand edge of the object becomes the profile. The photo never leaves this device.

    Shape

    Build it
    2.0 mm

    Measured square to the surface, so sloping walls are as thick as upright ones.

    3.0 mm

    How far up the inside starts. Raise it for a goblet so the stem stays solid.

    Downloads a solid shape. Turn on spiral vase mode in your slicer and it prints one continuous wall with a solid bottom. The capacity shown is an estimate for a 0.45 mm wall.

    128

    3 to 12 gives a faceted low-poly look; 96 or more looks smooth.

    Curve detail
    Cross-section
    5
    0.25

    How far the inner corners come in, as a share of the radius.

    0 °
    Surface
    24
    1.5 mm

    Hollow shapes get a thicker wall under flutes, so the thinnest point is still the wall you set.

    Extras

    A hole through suits a lamp cord. A cup in the top holds a candle. A hole underneath takes a dowel, screw or weight. Cups and blind holes need a solid shape.

    Measure what goes in it (candle base, cord plug, dowel) and add about 0.5 mm.

    For hollow shapes that close at the top, like the lidded jar in the library. The base keeps a lip; the lid slides over it.

    60 %
    6.0 mm
    0.20 mm

    Gap on each side of the lip. 0.2 mm is a snug push fit on most printers; print a small test first.

    Wrapped round the outside of round sections.

    Typeface
    Text style
    10.0 mm
    50 %
    0.8 mm

    Keep engraved text shallower than half the wall on hollow shapes.

    Printing

    Print it
    0.0 mm

    Slices this much off the bed side so round bottoms, eggs and tips stand flat.

    0.0 mm

    A 45° edge round the bottom that hides elephant’s foot.

    Download

    Building the preview…

    Print it well

      Everything is built on this device. Nothing you type or upload is sent anywhere.

      Advertisement

      The method

      How to turn a profile into a 3D print

      A lathe shape is the same all the way round, so one half outline is enough. You draw the right half against the axis, from the bottom up, and the generator spins it round.

      1. Profile: start from a library shape, drag the points, or trace a photo. Smooth points make curves; sharp points make corners.
      2. Shape: solid, hollow with a wall and floor, or spiral vase mode; facets, section, twist and ribs.
      3. Extras: a hole along the axis, a push-fit lid, or text round the body.
      4. Print: check the overhang list, flip it if that helps, and download.

      Options

      What each setting does

      SettingWhat it does
      SolidThe whole outline is filled. Best for game pieces, finials, knobs and tops.
      HollowAn inside wall offset square to the surface, a floor of its own thickness, and an open top (or a sealed hollow if the profile ends on the axis).
      Spiral vase modeA solid file for the slicer’s spiral (vase) mode, which prints one continuous wall.
      Segments roundHow many flat faces go round. Few faces give a low-poly look.
      Cross-sectionRound, square, hexagon or star, carried up the whole profile.
      Twist, ribs, flutesTurns the section as it rises, or adds raised ribs or cut flutes round the body.
      Hole along the axisA hole through (lamp cord), a cup in the top (candle) or a blind hole underneath (dowel or weight). Sizes are yours to measure.
      Push-fit lidSplits a closed hollow shape at a height: the base keeps a lip, the lid slides over it with the clearance you set.
      Flat base and chamferSlices the bed side flat and adds a 45° edge against elephant’s foot.

      Printing

      Printing tips

      • 45° rule: most printers manage surfaces up to about 45° from upright without supports. Steeper undersides show in red on the profile and in the list under it.
      • Upside down: shapes that are wide at the top often print better flipped. The generator says when flipping removes most overhangs and offers a button.
      • Spiral vase mode: keep the profile free of overhangs, and use a wider line width for a stronger wall.
      • Tips and eggs: a flat base cut gives them something to stand on, and a brim helps small bases stick.
      • Lids: print a short test of the split first and adjust the clearance by 0.05 mm.
      • Liquids: printed cups and vases can seep through layer gaps. A vase for real flowers needs a sealant or a glass insert, and nothing here is tested as food safe.

      Questions, answered

      Is it free to use?

      Yes. No account, no watermark, no limits.

      Will it fit my printer?

      Choose your printer below the preview to check. Use the height and diameter boxes under the profile to resize the whole shape.

      Does my photo get uploaded?

      No. Tracing runs in this browser and the photo never leaves your device. Shared links carry the profile points only.

      Can I make a cup or vase that holds water?

      The capacity readout tells you how much it holds, but printed parts can leak along their layers. Seal it or use an insert for water. We make no food safety claims.

      Can I sell what I print?

      The designs you make are yours. Typefaces are open licensed (OFL or Apache). We make no safety or compliance claims, so test anything you sell.

      Sources

      Print advice is a starting point drawn from these references, checked on 2026-11-13. Community posts are one maker's experience, not a specification.

      1. Support material: overhang threshold Prusa Research
      2. Support structures: overhang angles and bridging Polymaker Wiki
      3. Layers and perimeters (spiral vase) Prusa Research
      4. Elephant foot compensation Prusa Research
      5. Food safe FDM printing Prusa Research