Free generator · Runs in your browser

Keycap generator Your keys, your legends.

Make custom keycaps for MX-style switches: one key or a whole set, with raised, engraved or two-colour legends, sculpted rows, spacebars with stabiliser stems, artisan tops and a stem test-fit kit.

  • Private by designNothing leaves this device
  • 1u to 7uSets, spacebars and artisans
  • No supportsKeys print upright
  • Ready to sliceEvery key its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Keys

Make

1u is a letter key, 19.05 mm from one key to the next. Keys of 2u and longer get stabiliser stems.

Legend

Up to 12 characters. Use | for two lines, such as !|1 for a shifted number key.

Loads a list below. Edit it freely.

Separate keys with commas. Add a size after a colon (Shift:2.25, 0:2), 2v for a tall key (+:2v), or a row such as :R2. Start a key with * for the accent colour, use | for two lines and {up}, {enter}, {heart} and the other icon names for icons. Up to 80 keys.

Five stems in a strip, each with a slightly different cross socket around your clearance below. Press each onto a switch: the one that grips firmly without forcing is your setting. One to five dots mark the steps, from tightest to loosest.

Shape

Profile
Row

In a set, line 1 of the list is row R1, line 2 is R2 and so on. Add :R3 to a key to choose its row.

0.9 mm

How far the top curves in to cradle a finger. 0 is a flat top.

Top
2.5 mm

How far the artisan top rises above the profile.

1.2 mm
1.4 mm

At the thinnest point, under any engraving.

The test kit has no keycap shape: only the stem and its socket.

Legend

Legend style
Typeface
4.5 mm

Capital letter height. Long legends shrink to fit the top.

Position
0.6 mm
0.8 mm

The test kit marks each step with dots instead of text.

Stem and colours

0.15 mm

Added to the 4.1 × 1.17 mm cross socket. About 0.1–0.2 mm suits most filament printers; resin needs less. The test-fit kit finds yours.

4.0 mm

The switch stem stands 3.6 mm tall, so the socket must be at least that deep.

Print
Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make custom keycaps

    Choose one key, a whole set or the stem test-fit kit. The generator shapes each keycap for an MX-style switch, puts your legend on top and lays every key out on your printer’s plates.

    1. Print the test-fit kit first. Five stems with slightly different sockets show which clearance grips your switches best.
    2. Pick a size and profile, or type a set into the list: one keyboard row per line.
    3. Add legends: raised, engraved to paint, or a two-colour inlay, in any of eight typefaces or as an icon.
    4. Download and print upright, with no supports.

    Sizes

    Key sizes and stabilisers

    SizeKeycapTypical keyStabiliser stems
    1u18.00 × 18.00 mmLetters, numbers, F keysNone
    1.25u22.76 × 18.00 mmCtrl, Alt, modifiersNone
    1.5u27.53 × 18.00 mmTab, backslashNone
    1.75u32.29 × 18.00 mmCaps LockNone
    2u37.05 × 18.00 mmBackspace, numpad 023.876 mm apart
    2.25u41.81 × 18.00 mmLeft Shift, Enter23.876 mm apart
    2.75u51.34 × 18.00 mmRight Shift23.876 mm apart
    6.25u118.01 × 18.00 mmSpacebar100 mm apart
    7u132.30 × 18.00 mmSpacebar114.3 mm apart

    One unit (1u) is 19.05 mm (¾ inch) from one key to the next; each cap is 1.05 mm narrower so neighbours never touch. Stem spacing for 2–2.75u and 7u keys is from the switch maker’s data sheet; 6.25u uses the 100 mm spacing keyboard builders measure. Check your board’s stabilisers before printing a long key: some boards use other spacings.

    Profiles

    Profiles and tops

    ProfileShapeBest for
    Uniform sphericalEvery key the same height, with a round dishMixing and matching keys in any row
    Cylindrical sculpted rows R1–R4Each row its own height and tilt, curved side to sideA full set that feels like a typical office keyboard
    Low profileA shorter cap with a flat topTop-down printing and a smooth top face
    Artisan dome, wave or reliefA sculpted top for one keyAn escape key or a gift key

    These profiles are our own approximations, not copies of any commercial profile.

    Printing

    Printing tips

    • Upright, stem on the bed: the skirt and the stem both start on the bed, so nothing needs supports. The ceiling bridges across the cap; it is hidden inside.
    • Top down (stem up): for flat tops (the low profile with no dish). The top face prints on the bed and comes out smooth, and the stem grows straight up from it.
    • Layers: 0.12 mm or finer for crisp legends and a well-formed cross socket. The socket’s mouth flares slightly to cancel elephant’s foot.
    • Two colours on one nozzle: raised legends take a colour change at the first layer above the top; inlays need a multi-material printer, or a pause and a swap.
    • Resin: tilt keys 30–45° with supports on the inside of the skirt, never on the top or in the socket; wash the socket well and lower the clearance to about 0.05 mm, as resin prints true to size.
    • Fit: if the cap is loose, lower the clearance by 0.05 mm; if it will not go on, raise it. PLA is stiff and can crack if forced; PETG is more forgiving.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will they fit my keyboard?

    They are made for switches with a cross-shaped (MX-style) stem, which most mechanical keyboards use. Print the stem test-fit kit first to find the right clearance for your printer and filament. Low-profile switches with a different stem are not supported yet: we could not find published dimensions for their stems.

    Will it fit my printer?

    Choose your printer below the preview. A set spreads over as many plates as needed; a 7u spacebar is 132 mm long.

    Can I sell keycaps I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Make sure any picture or logo you upload is yours to use.

    Why does my key sit higher than I set?

    Inside every keycap the ceiling must clear the switch at the bottom of its travel. If a low dish or a thick top would put it too low, the generator raises the whole top to keep the key working.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. MX Series keyswitch data sheet (stem height, stabiliser spacing) Cherry, hosted by SparkFun
    2. Keycap mount (keycap slot cross 4.1 mm, arms 1.17 mm) Deskthority wiki
    3. Unit (key spacing) Deskthority wiki
    4. Spacebar sizes (6.25u stabiliser spacing) Deskthority forum
    5. Stabilisers: common sizes Self-Made Keyboards in Japan
    6. MX Black Clear-Top data sheet (4 mm travel) Cherry
    7. Color change Prusa Research
    8. SIL Open Font License SIL International