Free tool · Runs in your browser

STL to laser-cut slices Build it from flat sheets.

Turn an STL, 3MF or OBJ into stacked or interlocked slices for laser cutters, CNC routers, craft cutters or scissors. Every part is numbered and packed onto your sheets, with slots sized to the material you measured. Nothing is uploaded.

  • PrivateFiles never leave your device
  • Three constructionsStacked, interlocked or radial
  • Sized to your sheetSlots and layers from your thickness
  • Ready to cutSVG, DXF and a 1:1 PDF
Preview

Drop a file anywhere here · Drag to rotate · Scroll or pinch to zoom

0%
Slices
—
Sheets
—
Material used
—
Cut length
—

    Assembly order

      Parts

        Model

        STL and OBJ files don’t say their units.

        Turn 90° (which way is up)

        Size and material

        Show sizes in

        Type any one size and the others follow, so the model keeps its shape.

        Measure your sheet with calipers in a few places and type the average. Sheets sold as 3 mm are often a little thinner or thicker, and every slot and layer depends on this number.

        Examples only. Always type the thickness you measured.

        Each outline moves out by half of this, so parts come out at full size. To measure it, cut a 20 mm square and subtract its measured width from 20. Leave it at 0 for a craft knife or if your cutter software already makes up for it.

        Sheet

        5 mm
        3.0 mm

        Keep at least twice the material thickness on thin card or plywood that chars, so a hot edge doesn’t burn the next part.

        Turn this off if your material has a grain or a printed side that must run one way.

        Construction

        Construction

        Stack along the

        Round holes through the layers, placed where the most layers have solid material. A dowel through them lines every layer up.

        Measure your dowel, skewer or rod. The hole is the dowel plus the fit clearance below.

        Cuts the middle out of inner layers and keeps a wall, to save material. The top and bottom layers stay whole, and a solid strip is kept along the dowels.

        Draws the outline of the layer above on each part, as an engraving line, so you can place it without dowels.

        Added to every slot and dowel hole. Slots are the material thickness plus this. Cut two test slices first: if they are too tight, add 0.1 mm at a time.

        Specks narrower than this are left out.

        Numbers and colours

        Each part gets its number in single-line letters, placed where it has the most room.

        6.0 mm

        Red to cut and blue to engrave is common, but not universal. Use the colours your cutter software or makerspace asks for.

        Download

        SVG and DXF for every sheet, the PDF and a parts list.

        The layers as one closed model, for printing the layered look on a 3D printer.

        Open a file to slice it.

        Your file is read on this device and is never uploaded.

        Advertisement

        The method

        From a 3D model to flat parts

        This tool cuts a 3D model into flat slices you can make from sheet material: stacked or interlocked slices for laser cutters, CNC routers, craft cutters or scissors. It runs in your browser and nothing is uploaded.

        1. Open the model and type the finished size. One number is enough; the others follow.
        2. Measure your material and type its thickness. The number of layers, and the width of every slot, come from it.
        3. Choose the sheet your cutter takes. Parts are packed onto as few sheets as the tool can manage.
        4. Pick a construction: stacked, interlocked or radial. The 3D preview shows the result as plates of your material.
        5. Download the sheets as SVG, DXF or a PDF at full size, with an assembly guide.

        Construction

        Which construction to use

        ConstructionWhat you cutBest for
        Stacked layersOne flat part for every layer, cut from the model at the thickness of your materialSolid-looking sculptures, terrain, busts and lettering. The most parts and material, and the most faithful shape
        InterlockedTwo sets of slices at right angles, each with half-depth slots that slide togetherLight, open sculptures such as animal heads and lamps. Few parts and little glue
        RadialFins that point out from an upright centre line, slotted onto flat discsRound models: vases, domes, globes, fruit and bottles
        • Direction matters. Stacked layers show steps along the direction you stack. Stack along the shortest side for fewer parts, or along the side where steps look best, often the height for terrain and the depth for a face.
        • Pieces of one slice. Where a slice cuts through two separate parts of the model, such as two ears, each piece keeps the slice number and adds a letter: 12A, 12B.
        • Loose pieces. In interlocked and radial models every piece must be crossed by a slice from the other set. A piece that no slot reaches is listed in the checks, so you can change the number of slices.
        • Hollow stacks cut the middle out of inner layers and keep the wall you choose. The first and last layers stay whole so the model looks solid from outside.

        Material

        Choosing and measuring the material

        • Measure, don’t trust the label. Plywood, card and acrylic sold by a nominal thickness often differ from it by a few tenths of a millimetre. Interlocking slots only fit when the thickness is right.
        • Thinner material gives smoother steps and more parts. Thicker material gives fewer parts and a stronger model.
        • Card can be cut by hand. Print the PDF at 100% and glue each sheet to the card, or trace it.
        • Fit clearance. Slots and dowel holes are the material thickness or dowel diameter plus this clearance. Start at 0 for card and test two plywood slices before cutting the rest.

        Kerf

        Making up for the width of the cut

        A laser or router removes a thin strip of material, the kerf, so every part comes out a little smaller than its outline. Kerf compensation moves each outline out by half the kerf, and every hole and slot in by the same amount, so the parts finish at their true size.

        • Measure it on your machine. Cut a 20 mm square, measure it with calipers and subtract that from 20. The kerf depends on the machine, the lens, the power and the material, so measure again for a new material.
        • Don’t compensate twice. If your cutter software already offsets the cut, leave the kerf here at 0.
        • A craft knife or scissors have no useful kerf: leave it at 0.

        Cutting and gluing

        Cutting, numbering and assembly

        • Two colours. Cut lines and engraving lines are in separate colours and on separate layers in the SVG and DXF, named Cut and Engrave. Set each colour in your cutter software to cut or to engrave (or score).
        • Line weight. The SVG lines are very thin. Some cutters only cut lines set to “hairline”; set that in your software if it asks.
        • The numbers are drawn as single strokes, so an engraver draws them quickly. Turn them off to number the parts in pencil instead.
        • Assembly order. The page, the PDF and the parts list give the order: layers from the bottom, or the first set of slices then the second.
        • Glue stacked layers thinly with wood glue for plywood and card. Dry-fit interlocked models first; they often need no glue at all.
        • Print the PDF at 100% (“actual size”) and check the 50 mm bar before tracing parts by hand.
        SheetSize
        A4210 × 297 mm
        A3297 × 420 mm
        Letter215.9 × 279.4 mm
        12 × 20 in304.8 × 508 mm
        600 × 400 mm600 × 400 mm

        Limits

        What this tool doesn’t do

        • Packing is simple. Parts are packed by their bounding boxes in rows, turned a quarter turn when that fits better. A dedicated nesting program can pack odd shapes tighter.
        • Slices are straight and evenly spaced. There are no curved or hand-placed slices yet.
        • Models need a closed surface. A file with holes is repaired when it opens, but very broken files may lose outlines, which the checks report.
        • Up to 400 layers and 2 million triangles per job.

        Questions, answered

        Is it free?

        Yes. Every construction, sheet size and download is free, with no account.

        Is my file uploaded?

        No. The model is sliced by your browser, on your device. Nothing is sent to 3Dprintsy or anyone else.

        Which file should I give my cutter?

        Most laser software opens SVG. CNC and CAD programs usually prefer DXF; these are R12 polylines, which nearly every program reads. The PDF is for printing at full size, for scissors, a craft knife or a print shop.

        Can I sell what I make?

        The slices are made from your model, so what you may do with them depends on the model’s own licence. 3Dprintsy claims nothing over the files this tool makes.

        Why do my slots not fit?

        Usually the thickness. Measure the sheet again and type the exact number. If the fit is still tight, add 0.1 mm of fit clearance at a time; if it is loose, check the kerf setting.

        Why is a slice in more than one piece?

        The slice passes through parts of the model that only join elsewhere, such as legs or ears. Each piece gets the same number with a letter. Stacked pieces are held by the layers above and below; check that interlocked pieces are crossed by a slot.

        Can I 3D print the stacked look?

        Yes. Download the STL of the stacked layers: every layer is a closed plate that reaches a hair into the next, so your slicer reads the stack as one solid.

        How long will it take to cut?

        The total cut length is shown under the preview. Divide it by your cutter’s cutting speed for the material for a rough time, and add the engraving.

        Sources

        Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

        1. Accounting for kerf: how much material is really removed by your cutter Make:
        2. Laser cutting and engraving: file preparation Reed College
        3. Custom laser cutting: file set up instructions Pololu
        4. Scalable Vector Graphics (SVG) 1.1: units W3C
        5. DXF Reference Autodesk
        6. STL (STereoLithography) File Format Family Library of Congress