Free generator · Runs in your browser

Battery holder generator Any count, any layout.

Make battery holders and packs for AA, AAA, 18650, 21700, 9 V and coin cells, in series or parallel, with slots for spring contacts or channels for nickel strip.

  • Private by designNothing leaves this device
  • 1 to 8 cellsSeries, parallel or both
  • Sized to your partsMeasured contacts and cells
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Cells

Make

Holders take AA to D, 9 V and lithium-ion cells; spacer grids take round cells; coin holders take coin cells.

Shape

From the cell’s label or datasheet.

Measure the cell with calipers. Protected lithium-ion cells are often a few millimetres longer than bare ones.

2

Series adds voltage: 2 in series is 2S.

1

Parallel adds capacity at the same voltage. Up to 8 cells in a holder, 24 in a spacer grid, 4 in a coin holder.

0.30 mm

Pockets are the cell size plus this on every side.

Contacts

Contacts

9 V batteries always use a snap clip through a hole in the end wall.

Typical value only: measure your contacts with calipers.

0.15 mm

Each slot is the plate plus this on every side.

One wide slot where two cells link, for double contact plates. Off: a slot and a wire hole per cell.

Measure your strip. The channel is 0.6 mm wider.

The length both contacts take up with a cell pressed in: springs squashed plus flat plates. Added to the pocket length.

2.5 mm
Layout
1.5 mm

More gap leaves more air between cells.

1.0 mm

How far the ledge reaches under the cell edge.

1.0 mm
8.0 mm

Channels in the lip between linked cells, matching series and parallel links on each face.

Measure your strip.

Top contact
0.80 mm

Bare wire for the floor groove and the bar.

Box

Lid
1.6 mm
0.25 mm
2.0 mm
1.2 mm

Adds a bay at one end with a rectangular cut-out.

Typical small slide switch: measure yours.

A rectangular slot for a wire-to-board plug in the end bay.

Typical 2-pin plug: measure yours.

14 mm

Room behind the switch and plug, used when either is on.

3.4 mm

3.4 mm suits M3 screws.

Spacer grids have no box: the two plates hold the cells, and the pack is wrapped once it is welded.

Colours

The cells are never part of the download.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    Read first

    Battery safety

    • Lithium cells can be dangerous. A shorted, damaged or wrongly charged lithium-ion cell can overheat and catch fire.
    • No charging circuit is included. These are plastic parts only. Use a protection board (BMS) on every lithium-ion pack, and charge it with a charger made for it.
    • Never short the cells. Keep loose wire and metal tools away from the terminals, and insulate the pack.
    • Heat: PETG or ASA cope with warm cells better than PLA.
    • Damaged cells: stop using any cell that is swollen, dented or hot.
    • Coin cells are dangerous if swallowed: keep them away from children.

    We make no safety, fire or compliance claims for printed holders. Fire services publish battery safety advice (see the sources).

    The method

    How to make a battery holder that fits

    Pick the cell and how many go in series and parallel. Series cells lie end to end alternately, so each link is a short jump at one end. Then measure your contacts and set the room they take.

    1. Cells: type, series and parallel count.
    2. Contacts: measure the plate width, height and thickness, or choose nickel strip.
    3. Box: lid, switch and connector cut-outs, screw tabs.
    4. Download and print open side up, with no supports.

    Sizes

    Cell sizes and voltages used

    CellSizeNominal voltage
    AAØ14.5 × 50.5 mm1.5 V alkaline, 1.2 V rechargeable nimh
    AAAØ10.5 × 44.5 mm1.5 V alkaline, 1.2 V rechargeable nimh
    CØ26.2 × 50 mm1.5 V alkaline, 1.2 V rechargeable nimh
    DØ34.2 × 61.5 mm1.5 V alkaline, 1.2 V rechargeable nimh
    9 V48.5 × 26.5 × 17.5 mm9 V alkaline
    14500Ø14 × 50 mm3.6 V lithium-ion
    18650Ø18 × 65 mm3.6 V lithium-ion
    21700Ø21 × 70 mm3.6 V lithium-ion
    CR2032Ø20 × 3.2 mm3 V lithium coin
    CR2025Ø20 × 2.5 mm3 V lithium coin

    Sizes are the nominal sizes listed in the sources. Real cells vary a little, and protected lithium-ion cells are often longer, so measure yours and use a measured cell if it differs. Nominal voltage is the cell voltage times the number in series.

    Contacts

    What you measure, and what it sets

    You measureIt sets
    Contact plate width × heightSlot width and depth: the plate plus the slot clearance
    Contact plate thicknessSlot thickness
    Room for the contactsAdded to the pocket length, with the clearance
    Nickel strip widthChannel width on the end walls or spacer lip
    Switch and plug sizeCut-outs in the end bay

    There is no standard size for battery contacts, switches or plugs: the defaults are typical values only.

    Printing

    Printing tips

    • Open side up, no supports. The cradles are rounded and slots open from the top.
    • Lids: the slide-in lid prints flat; the snap-on lid prints lip up.
    • Spacers: print the two plates flat on the bed. Their strip channels differ, so keep them apart.
    • Test fit: print a one-cell holder first and adjust the clearance by 0.1 mm if needed.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview to check. Most holders are small; big spacer grids may need a larger bed.

    Can I charge batteries in it?

    No. It is a holder only, with no charging or protection circuit. Charge lithium-ion cells in a charger made for them, and use a protection board in packs.

    Which material should I use?

    PETG or ASA. PLA softens at about 60 °C, which a hard-working pack can reach.

    Can I sell what I print?

    The designs you make are yours. We make no safety or compliance claims, so test anything you sell and don’t promise more than you have tested.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. List of battery sizes Wikipedia
    2. BU-303: Confusion with voltages Battery University
    3. Lithium-ion batteries West Yorkshire Fire and Rescue Service
    4. PETG Prusa Research