Free generator · Runs in your browser

Magnetic fidget slider generator Slide. Snap. Repeat.

Make a print-in-place magnetic fidget slider that snaps into two to five positions. Choose your magnets, the travel and size, and add labels, a name or a keyring loop. No supports.

  • Private by designNothing leaves this device
  • Prints in placeThe slider prints captive in its frame
  • Your magnets6, 8 and 10 mm presets or your own
  • Ready to sliceSTL, 3MF and per-colour files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Magnets

Disc magnets (diameter × thickness)
8.0 mm
3.0 mm
Fitting the magnets

The pockets open on the bottom. Press the magnets in after printing, with a drop of superglue.

The pockets are sealed inside. Pause the print at the height shown below, drop the magnets in, and resume.

Cuts the preview in half at the magnets, so you can see where each one goes. Downloads are always the whole slider.

Slider

3

Two clicks at the ends, or more spaced evenly between them.

24 mm
18 mm
16 mm
2.5 mm

How far the slider sits above the frame, for your thumb.

0.300 mm

The gap between slider and frame. Use your tolerance-test result; 0.3 mm suits most tuned printers.

Labels and grip

Top of the slider

Short is best: a name, initials or a word.

Separate them with |, such as OFF | ON or 1 | 2 | 3. They’re raised on a wider rail.

Typeface
0.6 mm

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How the magnetic slider works

    The frame has no floor, so the slider and frame both print standing on the bed. A 45° V-shaped tongue on each side of the slider runs in a matching groove in the frame, with the clearance you set. That keeps the slider captive, and every surface leans at 45° or steeper, so nothing needs supports.

    Disc magnets stand on edge in the slider and in the frame’s rails, facing each other across the gap. At each click position, a rail magnet on each side pulls on the slider’s magnets, so the slider snaps into place and holds there until you push it on.

    1. Choose your magnets and how you’ll fit them.
    2. Set the click positions, travel and size.
    3. Add labels or a name, if you like.
    4. Print it, fit the magnets, then free the slider with a firm push.

    Magnets

    Getting the magnets the right way round

    Every magnet must pull, not push. The easy way:

    1. Make a stack of all your magnets. Mark the top face of the stack with a marker, then take them off one at a time, keeping the marked face up.
    2. Rail magnets: put every one in with the marked face toward the slider.
    3. Slider magnets: put both in with the marked face toward the slider’s centre, so their unmarked faces look out at the rails.
    4. Test before the glue sets: the slider should snap to each position. If one side pushes, flip that magnet.

    Sizes

    Magnet sizes

    MagnetFeelFrame height
    6×2 mmLight, quiet clicksAbout 8 mm
    8×3 mmFirm, satisfying snap (the default)About 10 mm
    10×3 mmStrong snap, bigger sliderAbout 12 mm

    Use neodymium disc magnets (N35 or stronger). Thicker magnets snap harder; more positions closer together feel smoother.

    Printing

    Printing tips

    • Orientation: print as laid out, flat on the bed, with no supports.
    • First layer: elephant’s foot can join the slider to the frame. The bottom edges are chamfered to help; lower the first-layer flow if it still sticks.
    • Pause for magnets: in your slicer, add a pause at the first layer above the height shown in the advice, which closes the pockets.
    • Freeing it: push the slider firmly end to end a few times.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Where do I get the magnets?

    Any shop that sells neodymium disc magnets. Buy the size you picked here: the pockets are sized for it with a 0.2 mm allowance.

    The slider is stuck. What now?

    Push it firmly from end to end to break the first-layer bond. If it won’t move, raise the clearance by 0.05 mm, or run the tolerance test to find your printer’s number.

    Is it safe for children?

    No, not for young children. Swallowed neodymium magnets can stick together inside the body and cause serious injury. Glue the magnets in well, and keep the slider away from small children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-09. Community posts are one maker's experience, not a specification.