Free generator · Runs in your browser

Spool holder generator Sized to the spool you measure.

Make a filament spool holder: a roller stand for one or two spools, a wall arm, adapters for your printer’s holder, a spinning desktop hub or sides for a refill. Bearing seats, bolt lengths and screw holes are worked out for you.

  • Private by designNothing leaves this device
  • Five holdersRollers to refill sides
  • No supportsEvery part prints flat
  • Ready to sliceSTL and 3MF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Holder

Make

The spool rests on two rollers, so any spool width or hole size works.

Spools side by side
30 mm

Must be wider than the bearing inside it: at least 26 mm for 608 bearings.

Rollers sit 2 mm off the floor and the end plates are trimmed, so the stand fits in a storage tub.

A plate screwed to a wall, shelf side or cabinet, with a bolt sticking out and a hub that spins on it.

The spool lies flat on a hub that spins on an upright bolt, and filament pulls off the top.

Two rings that fill a spool’s big centre hole, so it fits the holder your printer already has.

For refills sold without a spool, wound on a cardboard core: two sides press into the core’s ends. Measure the core; refill cores differ between makers.

82.0 mm

Measure across the inside of the cardboard tube, in two directions, and use the average.

60 mm
0.20 mm

How much smaller the plug is than the core. Lower for a tighter press; cardboard gives a little.

Your spool

Measure your spool with a ruler or calipers: there is no single standard size. Many 1 kg spools are about 200 mm across, 50–70 mm wide, with a 51–58 mm hole.

200 mm

Across the flanges. For refill sides, this is how big the sides are made.

65 mm

Outside of one flange to the outside of the other.

52.0 mm

For refill sides, the hole you want in the middle.

1.0 mm

How much smaller the hub is than the hole, so the spool slides on.

Bearings

Spins on
0.10 mm

Added to the bearing’s outside diameter. Lower for a tighter press fit.

No bearings to buy, but more friction: the part turns on the bolt or rod itself.

Axle
30.0 mm

Measure the rod or tube the spool hangs on.

0.50 mm

Added to the axle or holder diameter. More turns easier but wobbles.

Refill sides have no bearings: the finished spool goes on any holder.

Extras

A small guide that holds the end of a tube, so filament feeds smoothly.

4.0 mm

4 mm is common for 1.75 mm filament.

0.15 mm

Added to the tube size. Printed holes come out slightly small.

Guide fixing

Colours and view

Preview

Downloads are always laid out flat for printing, each part its own object.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a spool holder

    Pick the kind of holder, measure your spool and choose bearings or a printed bushing. The generator sizes every pocket, hub and plate from your numbers, lists the bolts and bearings to buy, and lays the parts out flat to print with no supports.

    1. Choose a holder: a roller stand, a wall arm, adapters for your printer’s holder, a spinning desktop hub or sides for a refill.
    2. Measure your spool: across the flanges, its width and its centre hole.
    3. Choose what it spins on: 608 or 625 bearings, or a printed bushing.
    4. Download, print and assemble with the hardware listed under the preview.

    Holders

    Which holder?

    HolderHow the spool turnsGood forHardware
    Roller standRests on two rollers; any width or holeShelves, desks and dry boxes; one or two spools2 rods, 4 nuts, 4 or 8 bearings
    Wall armOn a hub that spins on a boltWalls, shelf sides, cabinets1 bolt and nut, 2 bearings, 2 screws
    Hub adaptersFills the spool’s hole to fit your holderPrinters with a holder that’s too thin for the spoolOptional 2 bearings
    Spinning desktop hubLies flat, turns on a hubDesks; filament pulls off the top1 bolt and nut, 2 bearings
    Refill spool sidesMakes a spool of a refill’s cardboard coreRefills sold without a spoolNone

    Sizes

    Spool, bearing and bolt sizes

    Spools are not standard. Many 1 kg spools are about 200 mm across and 50–70 mm wide, with a centre hole of 51–58 mm, but makers differ, and cardboard spools differ again. So every spool size here is a measurement you enter.

    PartSizeWhere it comes from
    608 bearing8 × 22 × 7 mm (bore × outside × width)Bearing maker’s data sheet; the common skateboard bearing
    608 seat lip and spacersLip stops inside 20.5 mm; spacers 10.2–11.8 mm acrossThe data sheet’s mating-part sizes: spacers touch only the inner ring
    625 bearing5 × 16 × 5 mmBearing dimension table
    M8 bolt and nutHead 13 mm across flats, 5.3 mm tall; nut 6.8 mm; washer 16 × 1.6 mmISO 4017, ISO 4032, ISO 7089
    M5 bolt and nutHead 8 mm, 3.5 mm tall; nut 4.7 mm; washer 10 × 1 mmISO 4017, ISO 4032, ISO 7089
    PTFE tube4 mm outside, 2 mm inside is common for 1.75 mm filamentTube seller’s listing; measure yours
    ScrewHoleCountersink
    4 mm wood screw4.5 mm8.3 mm at 90°
    5 mm wood screw5.5 mm10.0 mm at 90°
    M4 machine screw4.5 mm7.9 mm at 90°
    3 mm wood screw3.4 mm6.3 mm at 90°

    Bearing seats are the bearing’s outside diameter plus Seat fit (0.1 mm by default), because printed holes usually come out a little small. Check your bearings with calipers: they can differ slightly.

    Options

    Bearings or a printed bushing?

    • Ball bearings turn with almost no effort, so the extruder doesn’t have to tug the spool round. 608 bearings are cheap and easy to find.
    • A printed bushing needs no bearings: the roller or hub turns on the rod itself, with a little clearance. It has noticeably more friction and wears with use. It works best on a smooth rod or the plain part of a bolt, with a little dry PTFE lube, and is fine for light use.

    Printing

    Printing and assembly tips

    • No supports: plates and bases print flat, rollers and hubs stand on end. The lower bearing pocket has a 45° ceiling, and the tube guide’s hole is a teardrop.
    • Bearings: press them in square with a vice, or a bolt with two washers. If one is loose, lower Seat fit by 0.05 mm.
    • Don’t over-tighten: on the wall arm and desktop hub, tighten the nut until the hub stops wobbling. A locking nut stays put.
    • Dry boxes: the low-profile roller stand sits the rollers 2 mm off the floor. PETG copes with a warm box better than PLA.
    • Strength: 3 walls and 20–30% infill. Screw wall plates into a stud or use wall plugs.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. The parts are laid out on its bed, over more than one plate if needed. Refill sides are as big as your spool, so a 200 mm side needs a bed at least that big.

    Will it fit my spool?

    It fits the sizes you measure. The roller stand is the most forgiving: the readout shows the range of spool sizes it holds, and width and hole size don’t matter.

    Can I sell holders I print?

    The designs you make are yours. Bearings, bolts and tubes are standard parts; no claims beyond that. A spool holder comes with no load rating, so check it holds your spools before relying on it.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. 608 high precision ball bearing data sheet (dimensions and mating-part sizes) GMN Bearing USA
    2. Ball bearing dimension table (608, 625) igus
    3. 3D printer filament: filament diameter and spool dimensions Snapmaker
    4. Filament spool RepRap wiki
    5. Bowden / PTFE tube, 4 mm OD 2 mm ID West3D
    6. DIN EN ISO 4017 hexagon head screws fasten.it
    7. DIN EN ISO 4032 hexagon nuts fasten.it
    8. DIN EN ISO 7089 plain washers fasten.it
    9. Metric countersunk machine screws, DIN 965 dimensions Westfield Fasteners
    10. Chipboard screw dimensions Kangaroo
    11. Tapping and clearance hole sizes (ISO 273 series) Optimas