Free generator · Runs in your browser

Marble run generator Drop it, watch it roll.

Make a modular marble run sized to your marbles: chutes, curves, U-turns, a funnel, a spiral, a zigzag and a splitter on tower posts, as single pieces or a whole set laid out on your printer’s plates.

  • Private by designNothing leaves this device
  • Eleven piecesOn one snap-together grid
  • No supportsEvery piece prints upright
  • Ready to sliceEach piece type its own colour

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Set or piece

Make
Layout
150 mm

Where the start hopper sits. A taller tower fits more pieces.

8

Between the start hopper and the finish cup. If the tower is too short for them all, the set uses as many as fit.

2
2 cells

How far each run goes before it turns back.

A fixed Y: each marble goes left or right by chance. It is not a flip switch.

2 cells
Turns
Turns
3
2 cells
2

Set the start hopper (or any piece) on the peg on top of the core: it pours into the top turn.

35 °

A wider grid pitch gives a wider funnel.

1 cells
6 steps

In tower steps (set below). Posts stack: each one’s peg fits the bottom of the next.

4 cells
3 cells

Marble and track

Marbles vary, so measure yours with calipers, or line up five and divide. Small glass marbles are often near 16 mm and big ones near 25 mm. Use your largest marble.

2.0 mm

The channel is the marble plus this on each side. More room suits marbles that are not quite round.

5.0 °

Steeper is faster. Below about 3° a marble can stop in the curves.

40 mm

The size of one grid cell. It goes up by itself if your marble needs more room to turn.

10 mm

Posts come in whole steps. Smaller steps waste less height between pieces.

Joints

Pieces fix to posts with

A square peg on each post and on the base plate; each piece has a socket under every cell. Square pegs stop pieces turning.

Each piece slides down over the top of its post. Pieces then always stand on a post at least one step tall.

0.20 mm

Gap on each side of the peg. Print one post and one piece first: raise this if they are too tight.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a marble run

    Every piece sits on a square grid. Tower posts stand on the base plate’s pegs, and each piece has a socket under every cell it covers, so it drops onto the posts below it. The track is an open U channel sized to your marbles.

    1. Measure a marble and type in its diameter.
    2. Build a set: choose a layout, a tower height and how many pieces. The generator finds a path from the start hopper to the finish cup, always downhill, and works out every post height.
    3. Or make one piece to extend a run you already have.
    4. Test first: print one post and one chute, check the peg fit and that the marble rolls freely, then print the rest.

    Pieces

    The pieces

    PieceCellsWhat it does
    Straight chute1 to 4 in a rowFalls at the slope you set
    90° curve1Turns left or right
    U-turn1 × 2Sends the marble back the way it came, one row over
    Funnel drop1The marble rolls into a cone, drops through the middle and rolls out of a tunnel underneath
    Spiral2 × 2One to three turns round a core; the start hopper sits on top
    Zigzag ramp2 to 4 by 2 to 5Back and forth in one piece
    Splitter (Y)1Sends each marble left or right by chance
    Start hopper1 or 2Holds a queue of marbles and feeds them in
    Finish cup1Catches the marbles
    Tower post1Stacks to any height in whole steps
    Base plateAnyPegs on every cell

    Sizes

    Marble sizes and channels

    Marbles are not one standard size: they range from about 5 mm to 35 mm across, and even one bag can vary. Measure the biggest one you will use.

    MarbleChannel (2 mm room each side)Smallest grid pitch
    14 mm18 mm34 mm
    16 mm20 mm37 mm
    22 mm26 mm47 mm
    25 mm29 mm52 mm

    The walls stand about two thirds of the marble’s height. The spiral’s pitch grows with the marble so there is always room under the turn above.

    Printing

    Printing tips

    • No supports: every piece prints standing on its slab, as laid out. The sockets and the funnel’s tunnel roof are short flat bridges, which printers handle without support.
    • The spiral has a 45° slope under each turn, onto the core. It runs at about 17°, so marbles go fast.
    • Layer lines: print chutes with fine layers (0.15 to 0.2 mm) for a quieter, smoother roll.
    • Fit: if pegs are tight, raise the joint clearance by 0.05 mm and print one post to check.
    • Plates: base plates sit side by side; posts and pieces across the joins keep them in line. Stand the run on a board or tape the plates underneath.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A set is laid out on as many plates as it needs, and tall towers are split into posts that stack.

    Can I sell sets I print?

    The designs you make are yours. Marbles and small parts are a choking hazard, so check the toy-safety rules where you sell (in the US, marbles and small balls need a choking warning) before selling to families.

    Is it safe for small children?

    No marble run with marbles is safe for children under 3: every marble, and any ball 44.4 mm (1.75 in) across or smaller, is a choking hazard. Big 25 mm marbles are easier for small hands, but they are still small balls. Always supervise play.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-11. Community posts are one maker's experience, not a specification.

    1. Marble (toy) Wikipedia
    2. 16 CFR 1500.19: misbranded toys and children’s articles (small balls and marbles) Legal Information Institute, Cornell Law School
    3. Small parts for toys and children’s products US Consumer Product Safety Commission
    4. Modeling with 3D printing in mind Prusa Research
    5. Support structures: overhang angles and bridging Polymaker Wiki