Free generator · Runs in your browser

Hose and vacuum adapter generator Any two hoses, one adapter.

Join a vacuum, dust port, garden hose or aquarium tubing to anything else: measure both ends, choose a straight reducer, elbow, Y-splitter, barb, stepped adapter, rectangular port or cap, and download a part that prints standing up.

  • Private by designNothing leaves this device
  • Seven typesReducers to Y-splitters
  • No supportsPrints standing up
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Adapter

Adapter
90 °
1.50

A wider bend flows better and catches less dust.

Print as

Two halves split at the middle of the bend, so each stands on its own end and leans no more than 45°. A spigot and socket line them up for gluing.

30 °

The outlets bend out and back up, so both point the same way, side by side.

Measure first. Every size here comes from your own calipers, not a brand’s catalogue. The bottom end prints on the bed; the top end points up.

Bottom end

Measure the rectangular port across its mouth, outside if the adapter goes over it, inside if it goes in.

Garden hose thread is the ¾ in, 11½ threads-per-inch thread on taps and hoses; its size is fixed.

Calipers across the part this end meets: the inside of a hose or socket, or the outside of a port or pipe. For a soft hose, wrap a paper strip round it and divide the length by 3.14.

This end goes
1.50 °

Many push-on vacuum fittings are slightly tapered. Measure the part near its tip and further back: taper ≈ (difference ÷ 2 ÷ distance) × 57°. Leave at 0 for straight pipe.

Small ridges on the fitting surface that bite into soft hose.

A flange (or, on an end that goes over a port, an inner lip) that stops the hose at the right depth.

A shallow groove under the hose where a worm-drive clamp sits.

A boss with a pilot hole: a screw through it locks the adapter onto the port.

30 mm

How far it slides in or over. Threads use 8–16 mm of it.

Top end

Both outlets use these settings.

A cap or plug has one end, closed at the bottom. Fitting inside makes a plug; fitting over makes a cap.

5
12 mm
The steps go

One stepped end fits several sizes. Saw it off at the step that fits, so the smaller steps don’t choke the airflow.

Calipers across the part this end meets: the inside of a hose or socket, or the outside of a port or pipe. For a soft hose, wrap a paper strip round it and divide the length by 3.14.

This end goes
1.50 °

Many push-on vacuum fittings are slightly tapered. Measure the part near its tip and further back: taper ≈ (difference ÷ 2 ÷ distance) × 57°. Leave at 0 for straight pipe.

Small ridges on the fitting surface that bite into soft hose.

A flange (or, on an end that goes over a port, an inner lip) that stops the hose at the right depth.

A shallow groove under the hose where a worm-drive clamp sits.

A boss with a pilot hole: a screw through it locks the adapter onto the port.

30 mm

How far it slides in or over. Threads use 8–16 mm of it.

Walls and details

2.4 mm

2–3 mm suits most vacuum and dust adapters.

0.30 mm

Added to a socket, taken off a spigot. Use 0 or below for a press fit into soft hose; raise it if prints come out tight.

30 °

Where the sizes change. 45° is the steepest that prints without support.

4 mm
0.4 mm
3.0 mm
3.0 mm
9.0 mm

Measure your clamp’s band and add a little.

The pilot hole is the tap-drill size, so the screw cuts its own thread.

3
1.0 mm

How far each ridge stands above the tubing’s inside diameter. Soft tubing takes taller ridges.

Colour and view

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a hose adapter that fits

    Measure the two things you want to join, pick an adapter type, and set each end to go inside or over what it meets. The generator sizes the ends from your numbers, joins them with a smooth cone, and checks the result prints standing up.

    1. Measure both parts with calipers, near where the adapter will meet them.
    2. Pick the type: straight, elbow, Y-splitter, barb, stepped, rectangular port or cap.
    3. Set each end: inside or over, its length, and a taper if the part is tapered.
    4. Add what holds it: grip ridges, a stop collar, a clamp groove or a set screw.
    5. Print a short test and adjust the fit clearance before printing the full part.

    Measuring

    Measure your hose

    • Into a hose or socket: measure the inside diameter at its mouth. Set the end to go inside.
    • Over a port or pipe: measure the outside diameter, about one fitting length back from its tip. Set the end to go over.
    • Soft or ribbed hose: calipers squash it. Wrap a strip of paper round the outside, mark the overlap, and divide the length by 3.14 to get the diameter.
    • Tapered fittings: measure near the tip and again 20 mm further back. Half the difference, divided by 20 and multiplied by 57, is the taper in degrees.
    • Rectangular ports: measure width, height and the corner radius at the mouth.

    Hose and accessory sizes are not standardised between makers, so this page gives no “standard” sizes. A patent for a vacuum adapter, for example, describes friction-fit tapers of under 5° on a 1¼ in hose end; your parts may differ.

    Options

    Adapter types and options

    OptionWhat it makesPrints
    Straight reducerTwo round ends of any sizes, joined by a coneUpright, no supports
    Elbow15° to 90°, with a smooth bend radiusTwo glued halves (no supports), or one piece: no supports up to 45°
    Y-splitterOne inlet, two outlets side by sideUpright, no supports
    Hose barbRidged spigot for soft tubing, sized to its inside diameterUpright, barb end down
    Stepped universalA stepped cone that fits several sizes; cut to sizeUpright, no supports
    Rectangular portA measured rectangle (sander, saw) to a round hoseUpright, no supports
    Cap or plugCloses a port or a hoseClosed end down
    Garden hose thread¾ in, 11½ threads per inch, male or femaleUpright; thread flanks print best slowly
    Grip ridges, stop collar, clamp groove, set screwWays to hold the fitShaped to avoid overhangs

    Printing

    Printing tips

    • Material: PETG handles heat and knocks better than PLA, so use it near motors, in a hot workshop or on tools that get dropped.
    • Airtight walls: set at least 3–4 walls (perimeters) so the adapter does not leak; a slightly higher extrusion multiplier helps too.
    • No supports: parts print standing up. Inside cones and collars stay at 45° or steeper; a set-screw hole has a short bridge over it.
    • Elbows: two halves each lean at most 45°. Glue the spigot into the socket with plastic glue or epoxy and press them together.
    • Fit: too tight? Sand the fitting surface with 240-grit paper or raise the clearance. Too loose? Lower the clearance or wrap a turn of tape.
    • Garden hose threads seal on the rubber washer, not the thread: keep the washer and tighten by hand.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview to check it fits the build volume. Long adapters can be made shorter by lowering each end’s length.

    Can I sell adapters I print?

    The designs you make here are yours. They are generic adapters sized from your own measurements; this page does not claim they fit any brand’s products, so check fit and function before selling.

    Why does my adapter not fit?

    Printers vary by a few tenths of a millimetre. Print one end at a short length first, then raise or lower the fit clearance.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Pivot adaptor attachment for vacuum cleaners (US 6,581,974 B1) Google Patents
    2. Thread dimensions: nominal dimensions of standard threads (GHT ¾ in: 1.0625 in, 11½ TPI) JME Ellsworth / Dixon
    3. Barb connectors in depth: design and function ISM
    4. List of drill and tap sizes Wikipedia
    5. Watertight prints Prusa Research
    6. PETG Prusa Research
    7. Modeling with 3D printing in mind Prusa Research