Free generator · Runs in your browser

Trinket tray generator Rings, keys, soap and notes.

Make a trinket or key tray, a ring dish with a ring cone, a soap dish with drains and a spout, a sticky-note holder or a valet tray with a phone slot, in a shape you pick or the outline of your own picture.

  • Private by designPictures stay on this device
  • Nine outlinesOr the shape of your picture
  • No supportsFillets and rims print as they are
  • Ready to sliceEach colour its own 3MF object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Tray type

80 %

Of the rim height above the floor. Lower dividers make small things easier to pick out.

2.0 mm

A cone stands at the roomiest point of the floor, for rings to slide onto.

22 mm

Wider than your biggest ring’s inside diameter.

11 mm

Narrower than your smallest ring.

42 mm

Water drips straight through, so the dish stands over the sink or on its own tray.

3.0 mm
Raised supports
2.0 mm

Holds the soap up off the wet floor so it dries.

A gap in the rim and a short lip that lets water run off.

22 mm
Note size

Measure your pad: sizes vary by brand and range.

1.00 mm

On each side, so the pad drops in and lifts out easily.

The outline is a rounded rectangle sized to the pad. Turn on the finger notch below to reach the last notes.

Two leaning walls at the back hold a phone upright; the rest of the tray takes keys, a wallet and a watch.

Measure at the thickest point, including the camera bump if it sits in the slot.

1.00 mm
14 mm

How tall the leaning walls are.

12 °

Up to 20°, so the walls print without supports.

Shape

Sticky-note holders always use a rectangle sized to the pad.

130 mm

Across a round tray; your own outline keeps its proportions inside the width and depth.

95 mm
6.0 mm

Rounds the corners and points of the outline: a rectangle’s corners, a heart’s tip, a cat’s ears.

Walls and floor

18 mm

From the bed to the top of the rim.

2.4 mm

1.2 mm or more is three lines from a 0.4 mm nozzle; 2.4 mm feels solid.

3.0 mm

Grows by itself when pad recesses and an inlay need more.

5.0 mm

A rounded inside corner, so small things slide out easily.

A soft, rounded edge along the top of the wall instead of a flat one.

A rounded dip in the front rim (the back on a soap dish with a spout).

30 mm
8 mm

Measure your self-adhesive pads. The recess is 0.4 mm wider.

0.5 mm

So the tray rests on the pads, not the plastic.

Floor design

One or two short lines. Initials make the boldest monograms.

45 %

Of the open floor, before it shrinks to fit the width.

Typeface
9.0 mm
1.2 mm

At least 0.8 mm (two lines from a 0.4 mm nozzle).

3

Each number scatters the dots differently.

Text and pattern style
1.2 mm

Your artwork, posterised into 2–4 colours and inlaid flush in the floor. Needs a multi-material printer.

3

Not counting the background, which is removed.

70 %
1.0 mm

For engraved and flush designs and the picture inlay.

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a trinket tray

    Pick what the tray is for and an outline, set the size and the walls, then add a name, a pattern or a picture to the floor. The generator rounds the inside corner where the floor meets the wall, so rings and coins slide out, and lays it all out ready to print flat.

    1. Pick the tray type: a trinket tray, ring dish, soap dish, sticky-note holder or valet tray.
    2. Pick the outline, or upload a picture or SVG and use its shape.
    3. Set the size and walls: height, rim, floor, fillet, notch and pad recesses.
    4. Decorate the floor with text, a pattern or a picture inlay.
    5. Download and print floor down, with no supports.

    Tray types

    Five trays from one generator

    TypeWhat it addsMeasure
    Trinket or key trayOne open tray, or 2–4 compartmentsNothing
    Ring dishA smooth ring cone at the roomiest pointYour smallest and biggest ring
    Soap dishDrain slots, raised ribs or a grid, and a drip spoutYour soap bar, so the tray is bigger
    Sticky-note holderA pocket sized to the pad and a finger notchYour pad, if it is not 76 × 76 mm
    Valet trayTwo leaning walls that hold a phone upright, and compartmentsYour phone in its case

    Sizes

    Sizes that work

    SettingDefaultNotes
    Rim thickness2.4 mm1.2 mm is the thinnest sturdy rim with a 0.4 mm nozzle
    Floor3 mmThicker automatically with pad recesses and inlays
    Fillet5 mmBigger is easier to sweep out; keep it small for sticky notes
    Sticky notes76 × 76 mmThe common square pad, 3 × 3 in
    Pad recessesMeasure your padsDiameter and thickness of your own self-adhesive pads
    Phone slotMeasure your phoneThickness in its case, plus clearance

    Printing

    Printing tips

    • No supports: the fillet and rounded rim are built up in thin steps, the ring cone tapers, and the phone walls lean at most 20°.
    • Two colours on one nozzle: with a raised design, a colour change at the floor height gives a two-tone tray (the walls change colour too).
    • Flush inlays and pictures need a multi-material printer; each colour is its own object in the 3MF.
    • Bathroom use: PETG copes with warm, wet places better than PLA.
    • Pads: stick self-adhesive rubber or felt pads into the recesses after printing.

    Safety

    Small parts and food

    Trays hold small things such as rings, coins and keys: keep them away from children under 3. A printed tray is not food-safe: use it for trinkets, not for food.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits, and your pictures never leave this device.

    Will it fit my printer?

    Choose your printer below the preview to check. If the tray is too big, lower the width or depth.

    Can I sell trays I print?

    The tray designs you make are yours, and the patterns are drawn by the generator. The typefaces are open-licensed, which allows making physical products. Only upload outlines and pictures you have the rights to use.

    Can I use my own shape?

    Yes. Choose Your own outline and add a picture or SVG: the biggest shape is traced, its holes filled and its edges smoothed.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Post-it Notes, 3 in × 3 in (76 mm × 76 mm) 3M
    2. Color change Prusa Research
    3. PETG Prusa Research
    4. Modeling with 3D printing in mind Prusa Research
    5. SIL Open Font License SIL International