Free generator · Runs in your browser

Cable drag chain generator Sized to your cables.

Measure your cables and make a drag chain for a 3D printer, CNC machine or robot: links sized to the bundle, a bend radius they can’t bend tighter than, lids, separators, end brackets and the right length for your travel.

  • Private by designNothing leaves this device
  • Snap or print in placeLids and separators too
  • No supportsLaid out to print as is
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Cables

Lay the cables side by side as they will run and measure across them with calipers or a ruler.

Measure the thickest point of the bundle, usually where the thickest cable sits.

2.0 mm

Added to the width and to the height. Cables should lie loosely in the chain, never squeezed.

The bend radius is set by the thickest cable.

Bend radius
10.0 ×

10 × is the common rule for cables that flex all the time. If your cable’s datasheet gives a smaller moving bend radius, you can use that.

Measured to the middle of the links. Check your cable’s datasheet for its smallest bend radius in motion.

Links

2.0 mm

Each side plate and the crossbars. Thicker walls are stiffer; the pitch grows with the link size.

0.30 mm

The gap round each pin and between the side plates. 0.3 mm suits most printers; print-in-place chains may need a little more.

Joints

Links print apart. Press each link’s pins into the next link’s holes until they click.

Links print already joined, in runs that fit your bed. Snap the runs together end to end.

Top

Each link gets a lid that clicks into grooves in its sides, so you can open it to add a cable.

0

Walls that keep cables apart in equal compartments, so they can’t tangle or rub.

Length

Length from

Fix the still end at the middle of the travel. The chain is half the travel, plus π × the bend radius, plus two links.

20

Ends

Flat: screws into the surface the chain lies on. Upright: screws into a wall across the end of the chain.

Wood screw heads from DIN 7997 sit in countersinks; machine screws get plain clearance holes.

Preview

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a drag chain that fits

    A drag chain guides the cables to a moving part, such as a printer’s print head or a CNC gantry, so they bend in one smooth loop instead of snagging or kinking. Here you measure your own cables, and the links, the bend radius and the length are worked out for you.

    1. Measure the cable bundle and the thickest cable.
    2. Choose the joints: snap-together links, or a print-in-place chain.
    3. Enter the travel, or a number of links.
    4. Pick the end brackets and screws, then download and print as laid out.

    Sizes

    What you set, and what it makes

    You setIt makes
    Bundle width and heightInside of each link = bundle + room
    Wall thicknessSide plates and crossbars; outside = inside + about 4 walls
    Link heightPitch (link length) and pin size, worked out from it
    Thickest cableBend radius = cable × multiple (10 × by default)
    TravelNumber of links (whole links, rounded up)
    ClearanceGap round each pin and between the plates

    Inner sizes are only as good as your measurement: cables should lie loosely in the links, never squeezed or twisted.

    Bend radius

    Why the bend radius matters

    Cables that flex all day wear out fast if they bend too tightly. A cable carrier maker’s design guide quotes the NFPA 79 rule: a carrier should give each cable a bend radius of at least 10 times its diameter, set by the thickest cable or hose in it. Cables built for constant flexing may be rated for less: their datasheet gives the figure.

    Each link’s front plate ends in a slanted edge that meets the next link when the joint reaches the angle of your bend radius, so the chain can’t bend tighter. Bent the other way, it stops a few degrees past straight, so a long chain doesn’t sag. Very small radii are raised to the tightest the links allow; the readout shows both.

    Length

    How long the chain is

    With the still end fixed at the middle of the travel, a maker’s selection guide gives the chain length as half the travel plus a bend add-on, with the add-on equal to π × the bend radius plus two links. We round up to whole links. Example: 300 mm of travel at a 50 mm radius with 23 mm links needs 150 + 157 + 46 = 353 mm, so 16 links (368 mm).

    If the still end can’t sit at the middle, add the distance it is off-centre, or add links and test before cutting the cables to length.

    Fixings

    End bracket screw holes

    ScrewHead (DIN 7997)HoleCountersink
    3 mm countersunk wood screw5.6 mm3.5 mm6.2 mm
    4 mm countersunk wood screw7.5 mm4.5 mm8.1 mm
    5 mm countersunk wood screw9.2 mm5.5 mm9.8 mm
    6 mm countersunk wood screw11 mm6.5 mm11.6 mm
    3.5 mm countersunk wood screw6.5 mm4.0 mm7.1 mm
    4.5 mm countersunk wood screw8.3 mm5.0 mm8.9 mm
    M3 machine screw (through hole)—3.4 mmnone
    M4 machine screw (through hole)—4.5 mmnone

    Wood screw heads are the nominal DIN 7997 sizes; the hole is 0.5 mm bigger than the thread and the countersink 0.6 mm bigger than the head. M3 and M4 holes are the ISO 273 medium series. The flat bracket screws into the surface under the chain; the upright one into a wall across its end, with the heads on the chain side.

    Printing

    Materials and printing tips

    • PETG for chains that move a lot: it bends further before it breaks than PLA, so pins and snap lids last longer. PLA is fine for a light printer chain away from heat.
    • As laid out, no supports: links print standing up. Pin holes are teardrops, pointed at the top, and the lid grooves are 45°, so nothing needs supports.
    • Print-in-place: print one short run first. If the joints are fused, raise the clearance by 0.05–0.1 mm; elephant’s foot on the first layers is the usual cause. Bend each joint gently to free it.
    • Snap-together: press the pins into the next link’s holes from the side; the outer plates spring open and click shut.
    • Small parts: tiny links and lids are small enough to swallow. Not for children under 3.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Links, lids and brackets fill as many plates as needed, and print-in-place chains are cut into runs that fit the bed.

    How much will it carry?

    We don’t give load or lifetime ratings. A printed chain guides light cables on hobby machines; it is not a replacement for a rated carrier on industrial machines. Test it on your machine before you rely on it.

    Why did my bend radius change?

    The links can only stop at angles their shape allows. A radius tighter than that is raised so a wall stays round each pin; a very wide one is cut so the links still have a gap when the chain lies straight. Taller links allow a wider radius.

    Can I sell what I print?

    The designs you make are yours. We make no claims about load, wear or safety, so test anything you sell and don’t promise more than you have tested.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. e-chain designing: calculation of the chain length igus
    2. e-chain designing: terms and abbreviations (K = R·π + 2T) igus
    3. How to select the bend radius of a cable carrier (NFPA 79: 10 × cable diameter) igus
    4. DIN 7997: cross-recessed countersunk head wood screws, dimensions fasten.it
    5. Tapping and clearance hole sizes (ISO 273 series) Optimas
    6. PETG Prusa Research
    7. Elephant foot compensation Prusa Research