Free generator · Runs in your browser

Display riser and collectible shelf generator Sized to your shelf.

Make tiered risers, wall cubby shelves, model car bays, minifigure stands and named plinths, sized to your measured shelf and collection, with LED channels, a dust-cover slot and modules that fit your printer.

  • Private by designNothing leaves this device
  • Five kindsRisers, shelves, bays, stands
  • No supportsEverything prints as laid out
  • Ready to sliceModules join with pegs

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Make

Make

Steps that lift the back rows so every figure on a shelf can be seen.

A grid of boxes that hangs on the wall, one figure in each.

Wall bays for small die-cast cars, such as 1:64 scale. Measure your cars: sizes differ between makers.

Tiered rows with studs that fit the common 8 mm stud building-brick system, or plain pegs.

A stand for one figure, with its name on the front.

Size

4
300 mm

The riser’s width. Anything wider than your printer is split into modules that join with pegs.

Step depth
200 mm

Shared equally between the steps.

60 mm

Front to back. Your figure’s base plus a little room.

30 mm

How much higher each row stands than the one in front.

In mm, separated by commas: 30 x 60, 40 x 60, 50 x 70.

60 mm

Only used to estimate how many figures fit.

3
4

Starting sizes only: measure your figure, or its box if you keep it boxed.

70 mm
90 mm
70 mm

Measure your longest, widest and tallest car.

75 mm
30 mm
30 mm

A 3 mm lip so cars don’t roll out.

4.0 mm

Added to every measured size, so things slide in easily.

2.4 mm
4.0 mm

At least 5.8 mm with keyholes.

3
6
4

Each stud is 8 mm. 4 studs leaves room for arms and accessories.

3
12 mm

0 for a flat plate.

Shape
60 mm

Measure the figure’s base and add a margin.

22 mm

Options

Body
Back
2.4 mm

A channel just under each step’s front edge, so a strip there lights the step below.

10.0 mm

Measure the strip itself, not the reel.

2.5 mm

Including the LEDs.

Use a battery or USB LED strip: never mains wiring in a printed part. The channels run out at the riser’s sides for the wire.

Mounting

Head sizes from DIN 7997. For other screws, choose Measured.

A slot across the front, open at the top, so a clear sheet slides down into it.

Measure your sheet with calipers: sold thicknesses vary.

0.4 mm

Added to the sheet thickness.

Figure feet
0.00 mm

Studs are 4.9 mm. Too tight? Lower it a little; too loose? Raise it.

3.0 mm
2.0 mm
9 mm
Typeface

A base with a printed pin: the plinth spins on it. No ball bearings needed.

Colours

Colour
Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a display riser or shelf

    Bought risers and shelves come in fixed sizes. Here you measure your shelf and your figures, and the generator sizes every step, cubby or bay to them, then splits anything too big for your printer into modules that join with pegs.

    1. Pick what to make: a riser, a wall shelf, car bays, a minifigure display or a plinth.
    2. Measure: the shelf width and depth, or your figure, box or car. The numbers shown are starting values, not standard sizes.
    3. Choose options: hollow or solid, LED channels, keyholes or a French cleat, a dust-cover slot.
    4. Pick your printer below the preview, then download and print as laid out.

    Sizes

    What each size means

    MakeYou measureWhat we make
    Tiered riserShelf width and depth, step heightSteps exactly the height and depth you enter
    Wall shelfFigure or box width, height, depthEach cubby that size plus the clearance
    Car displayCar length, width, heightEach bay that size plus the clearance
    Minifigure displayNothing: studs are fixed4.9 mm studs, 1.8 mm tall, on an 8 mm pitch
    PlinthThe figure’s baseA plinth the width you set
    Dust coverSheet thicknessA slot the sheet’s thickness plus the clearance
    LED channelStrip width and thicknessA channel 0.6 mm taller and 0.4 mm deeper than the strip

    Joining pegs are 4 mm square and 9.4 mm long, in 4.3 mm pockets 5 mm deep. The French cleat is a 30 mm strip, 8 mm thick, with a 45° bevel.

    Printing

    Printing and hanging tips

    • Risers print standing up. Hollow risers have treads that bridge between walls; for very deep steps, print one test step first.
    • Shelves print flat on their back with the cubbies open upwards: no supports.
    • Pegs: push them into one module, add a drop of glue if you want it permanent, and press the next module on.
    • Keyholes: leave the screw heads about 2 mm off the wall and hang the shelf down onto them.
    • French cleat: screw the wall cleat level with the bevel up and facing the wall, glue the shelf cleat near the top of the back with its bevel facing down, and the spacer at the bottom.
    • Dust cover: cut each sheet to the size in the advice, and slide it in from the top before stacking modules.
    • Load: we don’t give load ratings. Use wall plugs suited to your wall and test the shelf before you fill it.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Risers, shelves and minifigure displays wider than the bed are split into modules that join with pegs. A riser deeper than the bed needs fewer or shallower steps.

    Will the studs fit my bricks and figures?

    The studs use published measurements of the common 8 mm stud system. Printers differ, so print a small display first and use the stud size adjustment if the fit is too tight or loose. Studs and pegs are small parts: not for children under 3.

    Can I sell displays I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Don’t use other companies’ names or logos on what you sell, and we make no claims about load or safety.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Dimensions: general considerations (stud sizes) Robert Cailliau
    2. DIN 7997: cross-recessed countersunk head wood screws, dimensions fasten.it
    3. French cleat Wikipedia
    4. 1:64 scale (box scale) Wikipedia
    5. Modeling with 3D printing in mind Prusa Research
    6. SIL Open Font License SIL International