Free generator · Runs in your browser

Fan grill generator Guard any fan.

Make a grill or finger guard for any square fan from 25 to 140 mm: honeycomb, rings, turbine, slots or your name cut out. The open area updates as you go. Add a filter holder or a spacer, or adapt one fan size to another.

  • Private by designNothing leaves this device
  • Eight patternsFrom honeycomb to your name
  • No supportsPrints flat
  • Ready to sliceHoles from fan drawings

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Fan

Make

The frame’s outside width. Measure across the fan if you are not sure.

Adapter
25 mm

It grows if needed so the taper stays at 45° or steeper, which prints without supports.

Hole spacing

Measure between the centres of two holes on the same side.

Pattern

The adapter has an open hole the size of the smaller fan, with no grill.

8.0 mm

From the middle of one hole to the next. Smaller cells keep out smaller fingers and cables, and block a little more air.

0 °
24 mm
7

Each number shuffles the cells into a new layout.

4

Fewer fit on small fans: each needs a bar and a 2.5 mm gap.

8
25 %

Covers the motor hub, which moves no air. As a share of the opening.

45 °

Rings and the centre disc print on the bed, with the spokes across them: the bed side faces out, like a wire guard.

Cut out
Typeface
Shape
24 mm

It shrinks if it would not fit the fan circle.

Strength

1.6 mm

The thinnest bar. It never goes below two nozzle widths, so every bar is at least two lines wide.

2.4 mm
Outer edge
0.8 mm

Filter holders keep a square edge for their walls.

Screws

The adapter takes the screws suggested for each size: clearance holes for the larger fan, pilot holes for the smaller one.

The screw’s thread diameter plus about 0.3 mm.

Screw heads

Extras

3.0 mm

Measure your filter sheet lightly squeezed, as it will sit under the frame.

A separate ring that holds the grill away from the fan or a surface. You need longer screws.

10 mm

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a fan grill

    Pick your fan’s size and a pattern. The generator places the mounting holes from published fan drawings, opens the pattern as wide as the frame allows, and keeps every bar at least two nozzle widths wide. The open area updates as you change it, so you can see how much air gets through.

    1. Pick the fan size, or measure the hole spacing if your fan is unusual.
    2. Choose a pattern and its cell size. Smaller cells keep out smaller fingers and stray cables.
    3. Set the screws: plain, countersunk or counterbored holes.
    4. Add extras: a filter holder, a spacer, or an adapter to a different fan size.
    5. Download and print flat, with no supports.

    Fan sizes

    Fan sizes and mounting holes

    FanHole spacingHole in the fanSuggested screw
    25 mm20 mm2.8 mmM2.5
    30 mm24 mm3.2 mmM3
    40 mm32 mm3.5 mmM3
    50 mm40 mm4.3 mmM4
    60 mm50 mm4.5 mmM4
    70 mm61.5 mm4.3 mmM4
    80 mm71.5 mm4.5 mmM4
    92 mm82.5 mm4.5 mmM4
    120 mm105 mm4.5 mmM4
    140 mm124.5 mm4.3 mmM4

    Spacing is centre to centre between two holes on one side, as drawn in the fan makers’ datasheets (see Sources). Makers differ a little. One 70 mm fan drawing gives 61.5 mm, while a common reference table gives 60 mm. For 140 mm fans, some drawings give 124.5 mm and others 125 mm. If your fan is different, choose Measured and type in what you measure.

    Patterns

    Patterns and airflow

    PatternTypical open areaGood for
    Rings and spokes60–80%Most air, like a classic wire guard
    Turbine55–80%The same with curved spokes
    Wire finger guard60–80%Rings on the outside, spokes behind
    Slotsabout 70%A clean look on cases
    Honeycombabout 64%Even strength in every direction
    Square gridabout 64%Fine mesh for small fans
    Cellsabout 64%An organic look
    Name or picturevariesA name or logo, with automatic bridges

    The open area is the share of the fan circle left open. The figures above are for the default settings and change with bar width and cell size. Thinner bars and bigger cells let more air through, but leave bigger gaps.

    Screws

    Screws and holes

    ScrewClearance holeCountersunk headCounterbore
    M2.52.9 mm4.7 mm5.5 mm × 2.5 mm deep
    M33.4 mm5.5 mm6.5 mm × 3 mm deep
    M44.5 mm8.4 mm8.5 mm × 4 mm deep

    Clearance holes are the medium series from ISO 273. Countersinks fit the largest countersunk head allowed by ISO 7046-2. Counterbores fit socket head cap screws (ISO 4762). On thin frames the counterbore is shallower than the head, so the head stands proud. Pick a low-head screw, or a plain hole.

    Small fans (25–40 mm) usually take M2.5 or M3 screws. Case fans usually come with self-tapping screws about 10 mm long. Their thread size is not published, so measure one and choose Measured screw, or use M4 screws and nuts through the fan’s 4.3–4.5 mm holes.

    Extras

    Filter holder, spacer and adapter

    • Filter holder: four low walls on the grill hold a cut sheet of filter, and a thin frame snaps in on top under small beads. The countersunk screws sit flush under the filter, and the frame’s corners stay clear of the screw heads.
    • Spacer: a separate ring that holds the grill away from the fan or a surface. Use screws longer by the spacer’s depth.
    • Adapter: a plate with both fans’ holes. The larger fan bolts through clearance holes. The smaller fan’s screws cut their own thread in pilot holes. The tapered duct narrows at 45° or steeper and prints standing up, with no supports.

    Printing

    Printing tips

    • Orientation: print as laid out, screw-head side up. The wire finger guard prints with its rings on the bed.
    • Bars: each bar is at least two nozzle widths, so the slicer can fill it with two lines. Check that thin wall detection is on.
    • Material: PETG or ABS/ASA near warm parts. PLA can soften near hot ends and in hot cases.
    • Snap beads and duct: print a test first. Fit depends on your printer and filament.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A 140 mm grill needs a bed at least 140 mm square. The clip frame and spacer go on the same plate if there is room, or on another one.

    Will it fit my fan?

    The holes follow published fan drawings for each size. Makers differ by a fraction of a millimetre, so measure your fan’s hole spacing if a grill must line up exactly, and use Measured spacing.

    Is it a safety guard?

    It keeps fingers, cables and pets away from slow PC and printer fans. It is not tested to any safety standard, so do not rely on it for fast or powerful fans, or where a standard applies.

    Can I sell grills I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. A picture you cut out must be yours to use.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Computer fan: fan sizes and screw hole spacing Wikipedia
    2. AFB 25 × 25 × 10 mm series datasheet Delta Electronics
    3. ASB 30 × 30 × 10 mm series datasheet Delta Electronics
    4. FFB 40 × 40 × 28 mm series datasheet Delta Electronics
    5. AFB 50 × 50 × 15 mm series datasheet Delta Electronics
    6. AFB 60 × 60 × 20 mm series datasheet Delta Electronics
    7. AFB 70 × 70 × 20 mm series datasheet Delta Electronics
    8. AFB 80 × 80 × 25.4 mm series datasheet Delta Electronics
    9. AFB 92 × 92 × 25.4 mm series datasheet Delta Electronics
    10. AFB1212HHE-F00 specification for approval Delta Electronics
    11. F14 series 2D drawing ARCTIC
    12. IS 1821:1987 Dimensions for clearance holes for bolts and screws (identical with ISO 273) Bureau of Indian Standards
    13. ISO 7046-2:2011 Countersunk flat head screws, cross recess (preview) ISO, via iTeh Standards
    14. ISO 4762:1997 Hexagon socket head cap screws (preview) ISO, via iTeh Standards
    15. Counterbore drill bits: size chart AIMS Industrial
    16. Tapping sizes Optimas
    17. Everything you need to know about the screws used on the PC Hardware Secrets