Free generator · Runs in your browser

Pop-it fidget generator Any shape, every bubble.

Turn a shape, a letter or your own picture into a 3D printed pop-it: a grid of bubbles clipped to the outline, printed all in TPU or as a rigid frame with a TPU gasket, with rainbow rows and a key-chain loop.

  • Private by designPictures stay on this device
  • Any outlineShapes, letters or your art
  • Sourced bubble wallsPresets per TPU hardness
  • Ready to sliceEach colour its own 3MF part

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Shape

Make

Five single bubbles in a row with 0.5 mm, 0.62 mm, 0.8 mm, 1 mm, 1.2 mm walls, marked with one to five dots. Print it in your TPU and keep the wall that pops best.

A built-in shape, one bold letter, or your own picture or SVG.

One character. Bold, wide letters fit the most bubbles.

Typeface

Off fills gaps inside the outline.

120 mm

The longer side of the outline. A key-chain loop adds to it.

1.0 mm

Rounds sharp points and tight inside corners, which tear first in TPU.

5.0 mm
2.4 mm

TPU stretches, so give the loop a thicker wall than a rigid charm.

Build

How it is made

One TPU print: the bubbles sit on a thin membrane joined to a taller rim around the edge.

Two PLA or PETG frame halves with a hole for each bubble, and a flat TPU gasket with the bubbles, clamped between them. Pins on the bottom half go through the top half.

1.5 mm

The flat sheet the bubbles sit on. The Instructables guide used 1.5 mm.

1.5 mm
4.0 mm

A taller rim keeps the pop-it from curling.

A low ring a little outside each bubble. It catches the bubble as it pops and makes the pop snappier.

2.0 mm
1.0 mm
3.5 mm

Small holes between the bubbles make the sheet softer. Try it if your pop-it feels stiff.

1.6 mm
1.2 mm

The frame halves close 0.2 mm tighter than this, so they grip the gasket.

2.4 mm
5.0 mm

The solid band around the edge that holds the pins.

0.40 mm

Added all round each bubble, so it can pop through the frame.

2.4 mm
0.15 mm

Too loose: lower it and add a drop of glue. Too tight: raise it.

Preview

Bubbles

Grid
14.0 mm

Across the base of each bubble. The Instructables guide used 14 mm.

7.0 mm

Half the diameter gives a round half-sphere bubble.

Sets the bubble wall to the published value for that hardness. Print the test strip to fine-tune it.

0.80 mm

Thinner pops more easily but tears sooner. Under 0.8 mm is less than two lines from a 0.4 mm nozzle.

2.0 mm

Between neighbouring support rings, or bubbles without rings.

2.5 mm

Clear space between the edge and the nearest bubble. Grows to clear the rim or frame border.

Colours

Each row of bubbles is its own part, for a multi-material printer.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    Make a pop-it from any shape

    Pick an outline: a built-in shape, one letter, or your own picture. The generator lays a grid of bubbles over it, keeps every whole bubble that fits a margin inside the edge, and builds a pop-it you can print in flexible TPU. Everything runs on your device.

    1. Print the wall test strip first. Five bubbles with five wall thicknesses show which one pops best with your TPU.
    2. Pick the shape and size. Bold, chunky shapes fit the most bubbles.
    3. Choose how to build it: all in TPU in one print, or a rigid frame with a TPU gasket.
    4. Set the bubbles: diameter, height and the wall from your test.
    5. Print slowly and with no supports, then press each bubble through once to set it.

    Two ways to build it

    All TPU, or a frame and gasket

    FeatureAll TPUFrame and gasket
    PartsOne TPU printTwo PLA or PETG frame halves and one TPU gasket
    PrinterAny printer that prints TPUAny printer; TPU only for the gasket
    FeelFloppy and squishy, like a shop-bought oneStiff and flat, the bubbles pop inside a rigid frame
    Rainbow rowsEach row is a coloured part of the one printEach row is a coloured part of the gasket
    AssemblyNoneLay the gasket on the bottom half, press the top half over the pins, add a drop of glue if loose

    Some makers print the gasket inside the frame on a multi-material printer, or drop a pre-printed gasket in at a pause. This generator keeps the frame and gasket as separate parts, so any printer can make them.

    Sizes

    Starting sizes, and where they come from

    SettingDefaultSource
    Bubble14 mm across, 7 mm tallThe Instructables guide’s half-sphere bubble
    Bubble wall, 85A–90A TPU0.8 mmThe TPU pop-it model on MakerWorld
    Bubble wall, 95A HF TPU0.62 mmThe same MakerWorld model
    Membrane1.5 mmThe Instructables guide (three first layers)
    Rim1.5 mm wide, 4 mm tallThe Instructables guide
    Support ring2 mm outside the bubble, 1 mm wide, 3.5 mm tallThe Instructables guide (18 mm inside, 20 mm outside)

    The Instructables author made the wall twice the nozzle width (1 mm on a 0.5 mm nozzle) and found thinner walls printed stringy or tore. Filaments differ, so treat these as a start and use the test strip.

    Printing

    Printing TPU pop-its

    • Slow down. Flexible filament is usually printed around 20 mm/s, and 30–40 mm/s at most, or it tangles and clogs.
    • Keep it dry. TPU takes in moisture, which makes thin walls stringy and weak.
    • Less retraction: start with it low or off.
    • No supports. Each bubble prints as a hollow dome; its top is a short overhang that small TPU domes manage.
    • First layer: the bubbles stand on the bed, so a clean, well-stuck first layer matters most.
    • Check the slicer preview: walls under 0.8 mm can come out as one line or with gaps on a 0.4 mm nozzle.

    Be honest with yourself about the pop. Printed pop-its are firmer and less poppy than moulded silicone ones. The Instructables author found thinner, moulded-style walls failed or ripped, but still got a satisfying, audible pop.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits, and your picture never leaves this device.

    Will it fit my printer?

    Choose your printer below the preview. If it is too big, lower the size. With the frame and gasket, the three parts spread over as many plates as needed.

    Can I sell pop-its I print?

    The designs you make are yours, and the typefaces are open-licensed, which allows making physical products. Your own picture is the part to check: only use art you drew, bought a licence for or have permission to use. Pop-its are toys with small parts, so check toy-safety rules before selling them for children.

    Which TPU should I use?

    Softer TPU (85A–90A) pops most easily; harder 95A is easier to print. The Instructables author had the best results with an 85A filament. Print the test strip in the filament you have.

    Why does my pop-it barely pop?

    The wall is too thick for your filament, or the bubble is too flat. Try the next thinner wall from the test strip, a taller bubble, or support rings.

    Is it safe for small children?

    No. Pop-its with a key-chain loop, and the parts of the frame version, are small parts and a choking hazard for children under 3.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. 3D Printed Pop Its Instructables
    2. TPU Fidget Pop it Toys (wall thickness per TPU hardness, test model) MakerWorld
    3. Pop Fidget (multi-material design): a TPU gasket in a rigid frame Printables
    4. Flexible materials (print speed, retraction, drying) Prusa Research
    5. Insert pause or custom G-code at layer Prusa Research
    6. Small parts for toys and children’s products U.S. Consumer Product Safety Commission
    7. SIL Open Font License SIL International