Free generator · Runs in your browser

Three-letter cube generator Three views, one block.

Make a block that shows one letter from the front, another from the side and a third from above. Use initials, numbers, shapes or your own pictures, check that every shadow is complete, then download a file with its own plinth.

  • Private by designNothing leaves this device
  • Shadow checkShows how complete each view is
  • Best rotationFinds the way round that works
  • Ready to sliceSTL or two-colour 3MF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Design

What to make

One cube shows three shapes. A name row puts one cube under each letter of two or three words. A lantern is a hollow box with the shapes cut out, to stand over a battery tea light.

Front view

Front view shows

One character. Capitals and numbers fill the cube best.

Side view

Side view shows

Seen from the left side.

Top view

Top view shows

Seen from above.

Only for uploaded images: turn on if the shape is the light part.

Up to 6 letters or numbers. Use words of the same length.

Reads from the left side.

From above

Square leaves the top free, which gives the two words their best chance.

Three words in one row is the hardest case: check the shadows.

Letters

Typeface

Bold, blocky letters work best. Each letter must leave enough solid for the other two.

Letter shape

The three shapes only agree when each one spans its whole face, so stretching gives far more complete shadows. Very narrow letters such as I widen by up to 1.8 times.

0.0 mm

Thickens every stroke by this much on each side. Thicker letters share more solid.

2.0 mm

Thinner walls let more light through light-coloured filament.

Check and rotate

Tests every way round that still reads correctly and keeps the one with the most complete shadows.

Mirrors the front shape inside the block.

Mirrors the side shape inside the block.

Turn the top shape
Pieces that would float

Some combinations leave a piece hanging in mid-air, such as the dot of an i. A post shows as a fine line; leaving the piece out makes a gap in the shadow.

Size

30 mm

Each letter is this tall and wide. Pick your printer below the preview to check it fits.

4 mm

The row runs diagonally, so each word reads left to right from its own side.

Plinth

A lantern has no plinth: it stands over the light on its own walls.

Plinth

A round plinth sits well on a turntable. For a name row, Round follows the row closely and Square is a full square with room for a caption.

3.0 mm
5 mm

A name, a date or a few words on the plinth, in front of the cube.

Caption and marks
4.5 mm

Two small arrows point to where you stand for the front and side views; a dot marks the view from above.

A flat loop at the back, for cubes of about 15 to 25 mm.

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How a three-letter cube works

    Picture a solid cube. Push the first letter straight through it from the front, the second from the side and the third from above, and keep only the plastic that all three leave behind. What is left looks like the first letter from the front, the second from the side and the third from the top. This kind of block is often called a trip-let.

    1. Pick three shapes. A letter, a number, a built-in shape or your own black-and-white picture for each view.
    2. Check the shadows. The readout shows how complete each view is. Press Try best rotation if one falls short.
    3. Choose the size and plinth, and add a caption if you like.
    4. Download and print. Use the Front, Side and Top buttons above the preview to see each view first.

    Not every set of three works. Each part of a letter needs solid behind it, and the other two letters may have cut that solid away. The generator measures this for you: 100% means the shadow is whole, and anything less tells you which face has gaps.

    Options

    Settings at a glance

    SettingWhat it doesStarting point
    One cubeThree shapes in one block.Three capital letters
    Name rowOne cube per letter of two or three same-length words, set in a diagonal row so each word reads left to right from its own side.Two words, up to 6 letters
    LanternA hollow, floorless box with the shapes cut through the front, one side and the top. Loose middles are held by narrow bars.2 mm wall
    Stretch to fillWidens each shape to span its whole face, which the illusion needs.On
    Try best rotationTests reading the front from the back, the side from the right and the top in four turns, and keeps the best.Press once after choosing letters
    Pieces that would floatHolds them with a 1 to 1.6 mm post, or leaves them out.Thin posts
    PlinthRound, square or none, with a raised or engraved caption and view marks.Round, 3 mm thick
    Keyring loopA flat loop with a 5 mm hole at the back.Off

    Shapes that fill their square combine best: B, D, E, H, M, N, 8 and 0 are easy; thin or open shapes such as I, J, L, T, 1 and 7 leave less solid for the others.

    Printing

    Printing tips

    • Orientation: print a cube standing on its plinth, and a lantern upside down with its top on the bed.
    • Supports: most cubes have undersides that hang over air. The studio reports the share of the surface that overhangs by more than 45°. Tree or organic supports snap off cleanly; let them start on the model as well as the bed.
    • Posts: a floating piece is held by a thin post. It is part of the model, so it needs no slicer setting.
    • Two colours on one nozzle: add a colour change at the plinth thickness, where the cube starts.
    • Detail: 0.12 to 0.16 mm layers and three walls keep letter edges crisp. Cubes under 20 mm have thin parts that break easily.
    • Lantern light: use a battery or LED tea light only. Never use a candle with printed plastic.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits. Everything is built on your device.

    Will it fit my printer?

    Choose your printer below the preview. A single 30 mm cube fits any printer. A name row runs diagonally, which uses the bed’s longest direction; lower the cube edge or the gap if it is too big.

    Why is one of my letters incomplete?

    The three letters share one block, so each can only keep solid that the other two also keep. If a shadow is under 100%, press Try best rotation, pick a bolder typeface, raise the stroke weight, or change one letter. Thin letters such as I and L are the hardest to combine.

    Can I use my own picture?

    Yes. Choose Image for a view and upload a solid black shape on a white background. Simple, chunky silhouettes work best. Only use pictures you have the right to use.

    Can I sell cubes I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Names, words and pictures you print are your responsibility.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-13. Community posts are one maker's experience, not a specification.

    1. Gödel, Escher, Bach (the “trip-let” blocks on its cover) Wikipedia
    2. Organic supports Prusa Research
    3. Color change Prusa Research
    4. SIL Open Font License SIL International